The mechanical effect of soft pad on copper chemical mechanical polishing
Source abstract
Abstract
Smaller transistor size challenges traditional chemical mechanical polishing (CMP) in semiconductor fabrication. Novel consumables and in-depth mechanism research can support defect mitigation and improve yield. This study focused on soft pad polishing of copper film from the perspective of mechanical effects. To reduce the defects, a soft pad is replacing the hard pad in the barrier layer polishing and over-polishing steps of copper CMP. When the contact behavior of pad asperity and wafer was in the elastic-plastic regime, the exponential influence factors of pressure, abrasive concentration, and sliding velocity on the material removal rate (MRR) were around 0.64, 0.22, and 0.64, respectively. Stick-slip friction with squeal noise scratched the copper film at the beginning and end of the CMP process. The pad conditioning removed polishing residues but deflected the pad asperity. Proper conditioning frequency is necessary to optimize the polishing process.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Metal and Thin Film Mechanics · Adhesion, Friction, and Surface Interactions
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Damascene copper electroplating for chip interconnections10.1147/rd.425.0567 ↗
2. Gbondo-Tugbawa · 2002 · 34
3. Circuit design challenges at the 14nm technology node
4. Nano-scale scratching in chemical-mechanical polishing10.1016/j.cirp.2008.03.098 ↗
5. Effects of BEOL copper CMP process on TDDB for direct polishing ultra-low k dielectric cu interconnects at 28nm technology node and beyond
6. Microreplicated conditioners for Cu barrier chemical-mechanical planarization (CMP)10.1149/2.0011511jss ↗
7. W CMP process integration: consumables evaluation-electrical results and end point detection10.1016/S0167-9317(97)00132-9 ↗
8. Engineering surface texture of pads for improving CMP performance of Sub-10 nm nodes10.1149/2162-8777/abbcb5 ↗
9. Soft chemical mechanical polishing pad for oxide CMP applications10.1149/2162-8777/abdc40 ↗
10. Modeling of chemical-mechanical polishing with soft pads10.1007/s003390050766 ↗
11. Pad effects on material-removal rate in chemical-mechanical planarization10.1007/s11664-002-0038-2 ↗
12. A new nonlinear-micro-contact model for single particle in the chemical-mechanical polishing with soft pad10.1016/j.jmatprotec.2006.10.030 ↗
13. Improvements in stribeck curves for copper and tungsten chemical mechanical planarization on soft pads10.1149/2.0241705jss ↗
14. Huang · 2018 · 1
15. CMP defect reduction and mitigation: practices and future trends
16. Semi-empirical material removal model with modified real contact area for CMP10.1007/s12541-019-00161-6 ↗
17. A chemical mechanical polishing model incorporating both the chemical and mechanical effects10.1016/j.tsf.2003.09.060 ↗
18. Contact of nominally flat surfaces10.1098/rspa.1966.0242 ↗
19. Investigation of abrasive behavior between pad asperity and oxide thin film in chemical mechanical planarization10.1016/j.mssp.2021.106280 ↗
20. Investigation of copper removal mechanisms during CMP10.1149/1.1787497 ↗
21. The effect of pad-asperity curvature on material removal rate in chemical-mechanical polishing10.1016/j.procir.2014.03.014 ↗
22. Chemical-mechanical wear of monocrystalline silicon by a single pad asperity10.1016/j.ijmachtools.2017.05.001 ↗
23. Post Cu CMP cleaning of polyurethane pad debris10.1149/2.006401jss ↗
24. Influence of slurry components on uniformity in copper chemical mechanical planarization10.1016/j.mee.2007.12.044 ↗
25. Influence of slurry components on copper CMP performance in alkaline slurry10.1016/j.mee.2017.10.002 ↗
26. Investigation of thermal effects in copper chemical mechanical polishing10.1016/j.precisioneng.2021.08.022 ↗
27. A mechanical model for erosion in copper chemical-mechanical polishing
28. Study on abnormally accelerated oxidation of tungsten plugs during tungsten chemical mechanical polishing in semiconductor manufacturing10.1149/2162-8777/abe6f7 ↗
29. CMP challenges for advanced technology nodes10.1557/adv.2017.366 ↗
30. Tribological attributes of post-CMP brush scrubbing10.1149/1.1753586 ↗
31. Chemical mechanical polishing of Al and SiO2 thin films: the role of consumables10.1149/1.1392688 ↗
32. Choi · 2003 · 767
33. Jiang · 2007 · 991
34. Investigations of the pad trajectory effect on the asymmetric profile and arc-shaped scratches in chemical mechanical polishing10.1149/2162-8777/ac14db ↗
35. W.B. Horne, R.C. Dreher, Phenomena of Pneumatic Tire Hydroplaning, National Aeronautics and Space Administration1963.
36. Centrifugal and hydroplaning phenomena in high-speed polishing10.1016/j.cirp.2019.04.018 ↗
37. How do grooves on friction interface affect tribological and vibration and squeal noise performance10.1016/j.triboint.2016.12.043 ↗
38. Effect of surface roughness on friction-induced noise: exploring the generation of squeal at sliding friction interface10.1016/j.wear.2018.02.005 ↗
39. Effect of stick-slip on the scratch performance of polypropylene10.1016/j.triboint.2015.06.024 ↗
40. Nano-scale stick-slip friction model for the chatter scratch generated by chemical mechanical polishing process10.1166/jnn.2012.6389 ↗
41. Friction and thermal phenomena in chemical mechanical polishing10.1016/S0924-0136(02)00820-8 ↗
42. Characterization and modeling of dynamic thermal behavior in CMP10.1149/1.1560642 ↗
43. Pad conditioning for poromeric materials
44. Shape memory polyurethane foams10.3144/expresspolymlett.2012.7 ↗
45. Analysis of correlation between pad temperature and asperity angle in chemical mechanical planarization10.3390/app11041507 ↗
46. Transient copper removal rate phenomena with implications for polishing mechanisms10.1016/B978-0-12-821791-7.00007-1 ↗