Influence of single diamond wire sawing of photovoltaic monocrystalline silicon on the feed force, surface roughness and micro-crack depth
Source abstract
Abstract
To gain an in-depth understanding of the influence of diamond wire sawing of monocrystalline silicon on the feed force and wafer quality, experiments with a single diamond wire in the form of a loop were performed. The cutting parameters of wire cutting speed, feed rate and wire tension were varied. The feed force was monitored and surface roughness of the specimen was measured. The micro-crack depth was determined using an image processing. The results show that cutting conditions of higher feed rate and higher wire tension increased the feed force by 78% and 20%, respectively, since for chip removal these conditions is required a higher force per grain. On increasing the wire cutting speed, the feed force reduced by 66% due to a decrease in penetration depth of the grains. Based on an analytical model, it was evidenced that volume of material removed per wire length has a significant effect on feed force. The variation of the feed rate and wire cutting speed had a greater effect on surface roughness R a and R q, with a minor effect on R z. With a higher feed rate the micro-crack depth increased, whereas it was reduced on increasing the wire cutting speed. A strong correlation between sawn surface and subsurface damage was found, indicating that the micro-crack depth is around 1.37 times higher than R z value. The combination of a lower feed rate and lower wire tension with higher wire cutting speed resulted in lower feed force, smoother surface and shallower micro-crack depth.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research · Tunneling and Rock Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Wire sawing technology: a state-of-the-art review10.1016/j.precisioneng.2015.08.008 ↗
2. Wafering of silicon10.1016/bs.semsem.2015.02.003 ↗
3. Experimental investigation of the sawn surface of monocrystalline silicon cut by endless diamond wire sawing10.1590/1980-5373-mr-2020-0013 ↗
4. Effect of cutting parameters on surface integrity of monocrystalline silicon sawn with an endless diamond wire saw10.1016/j.solener.2020.07.018 ↗
5. Mechanical strength of silicon wafers cut by loose abrasive slurry and fixed abrasive diamond wire sawing10.1002/adem.201100263 ↗
6. Fracture strength of silicon wafers sawn by fixed diamond wire saw10.1016/j.solener.2017.08.063 ↗
7. Formation of subsurface cracks in silicon wafers by grinding10.1016/j.npe.2018.09.003 ↗
8. Ductile-regime grinding: a new technology for machining brittle materials10.1115/1.2899676 ↗
9. Klocke · 2008
10. Indentation fracture: principles and applications10.1007/BF00823224 ↗
11. Characterization of electroplated diamond wires and the resulting workpiece quality in silicon sawing10.1016/j.jmatprotec.2019.116390 ↗
12. Evaluation of fixed abrasive diamond wire sawing induced subsurface damage of solar silicon wafers10.1016/j.jmatprotec.2019.116267 ↗
13. Slicing mechanism of multi-wire sawing using electroplated diamond wire
14. Experimental investigation on the machining characteristics of single-crystal SiC sawing with the fixed diamond wire10.1007/s00170-015-7250-8 ↗
15. Experimental study on reciprocating electroplated diamond wire saws cutting SiC wafer10.4028/www.scientific.net/KEM.450.296 ↗
16. Fixed abrasive diamond wire saw slicing of single-crystal silicon carbide wafers10.1081/AMP-120029960 ↗
17. Multi-wire sawing of sapphire crystals with reciprocating motion of electroplated diamond wires10.1016/j.cirp.2013.03.122 ↗
18. Investigation on diamond wire break-in and its effects on cutting performance in multi-wire sawing10.1007/s00170-015-7984-3 ↗
19. Determination of cutting parameters for silicon wafer with a Diamond Wire Saw using an artificial neural network10.1016/j.solener.2017.04.022 ↗
20. Endless diamond wire saw for monocrystalline silicon cutting
21. de Souza · 2019
22. Montgomery · 2014
23. 2002 · vol 14 · 1
24. Experimental investigation of the machining characteristics in diamond wire sawing of unidirectional CFRP10.1007/s00170-021-07146-8 ↗
25. Depth of cut for single abrasive and cutting force in resin bonded diamond wire sawing10.1007/s00170-016-8896-6 ↗
26. Prediction of sawing force for single-crystal silicon carbide with fi xed abrasive diamond wire saw10.1016/j.mssp.2017.01.014 ↗
27. A macroscopic mechanical model of the wire sawing process10.1016/j.ijmachtools.2011.05.005 ↗
28. Experimental and simulational investigation of wire bow deflection in single wire saw10.1007/s00170-018-2919-4 ↗
29. Tönshoff · 2013
30. Malkin · 2008
31. Marinescu · 2015
32. Effect of crystal plane orientation on the friction-induced nanofabrication on monocrystalline silicon10.1186/1556-276X-8-137 ↗
33. Subsurface damage in some single crystalline optical materials10.1364/AO.44.002241 ↗
34. Optical glass fabrication technology 2: relationship between surface roughness and subsurface damage10.1364/AO.26.004677 ↗
35. Analytical modeling of grinding-induced subsurface damage in monocrystalline silicon10.1016/j.matdes.2017.05.068 ↗
36. Effect of wear of diamond wire on surface morphology, roughness and subsurface damage of silicon wafers10.1016/j.wear.2016.07.009 ↗
37. Relationship between subsurface damage and surface roughness of optical materials in grinding and lapping processes10.1016/j.jmatprotec.2007.11.118 ↗
38. Influence of diamond wire sawing parameters on subsurface microcracks formation in monocrystalline silicon wafer