Ba0.7Sr0.3TiO3 powders with B2O3 additive prepared by the sol–gel method for use as microwave material
Source abstract
Abstract
Ferroelectric films based on barium strontium titanates have been widely investigated in microwave devices, such as tunable filters and phase shifters. Recent trends include integration of ferroelectric layers into multilayer dielectric modules by a tape casting procedure. The sintering temperature of BST prepared by the conventional oxide mixing method is, however, very high (1350°C), and only platinum or refractory metals can be used for conductors and electrodes in the co-sintering process of tapes. Decrease of the sintering temperature of BST below 1000°C would result in good compatibility of the ferroelectric layers with embedded electrodes made of highly conductive metals, such as silver. The effects of B 2O 3 addition and powder properties on the sintering behavior and the dielectric properties were investigated. The sol–gel method was used to prepare all powders because of its high purity and homogeneity control and its ability to produce fine powders. The BET results showed that all powders had high specific surface areas, but in dilatometric studies, only boron addition produced the desired shrinkage and dense microstructure at low temperatures (<1000°C). This was also verified in sintered microstructures. The XRD showed an appearing of two secondary phases caused by boron addition. This decreased permittivity and thus set a limit on boron addition.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Ferroelectric and Piezoelectric Materials · Microwave Dielectric Ceramics Synthesis · Acoustic Wave Resonator Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. Planar microwave integrated phase-shifter design with high purity ferroelectric material10.1109/22.588610 ↗
2. Tombak A, Ayguavives FT, Maria JP. Low voltage tunable barium strontium titanate thin film capacitors for RF and microwave applications. IEEE MTT-S Dig 2000;(3):1345–48.10.1109/MWSYM.2000.861790 ↗
3. HTS/ferroelectric thin films for tunable microwave components10.1109/77.403270 ↗
4. Realization of high tunability barium strontium titanate thin films by RF magnetron sputtering10.1063/1.125272 ↗
5. Monolithic Ka-band phase shifter using voltage tunable BaSrTiO3 parallel plate capacitors10.1109/75.842071 ↗
6. Ceramic and glass-ceramic packaging in the 1990s10.1111/j.1151-2916.1991.tb04320.x ↗
7. Effects of B2O3 addition on the dielectric and ferroelectric properties of Ba0.7Sr0.3TiO3 ceramics10.1111/j.1151-2916.2000.tb01345.x ↗
8. Wang FY. Treatise on material science, technology, vol. 9, ceramic fabrication processes. New York: Academic Press, 1976.10.1016/B978-0-12-341809-8.50005-X ↗
9. Effects of heating rate on the sintering behavior and the dielectric properties of Ba0.7Sr0.3TiO3 ceramics prepared by boron-containing liquid-phase sintering10.1111/j.1151-2916.2000.tb01675.x ↗
10. Ferroelectric phase transition and maximum dielectric permittivity of displacement type ferroelectrics (BaxSr1−xTiO3)10.1063/1.1317243 ↗
11. Dielectric temperature characteristics of cerium-modified barium titanate based ceramics with core-shell grain structure10.1111/j.1151-2916.1997.tb02797.x ↗
12. Structure and electrical properties of boron-added (Ba,Sr)TiO3 thin films fabricated by the sol–gel method10.1016/S0040-6090(98)00560-4 ↗