journal article·2019-03

The effect of cut depth and distribution for abrasives on wafer surface morphology in diamond wire sawing of PV polycrystalline silicon

Xinying Li, Yufei Gao, Peiqi Ge, Lei Zhang, Wenbo Bi

Publisher page

Abstract

Abstract Due to the existence of an acid etch resistant thin amorphous silicon layer over the smooth grooves of the diamond wire sawing polycrystalline silicon wafer surface, the anti-reflection effect is usually not ideal using the mature acidic texturization. The amorphous silicon layer will be produced on the machined surface by material ductile removal. Therefore, during the process of cutting photovoltaic polycrystalline silicon wafers, the material removed in the brittle way is expected and the surface topography of the wafers formed with the brittle fracture is better for the texture fabricating. In this paper, a mathematical model considering the influences of process parameters and wire saw parameters was developed based on indentation fracture mechanics. The variations of cutting groove profile formed by different material removal modes were also included. The effect of abrasives distributed on the wire saw on material removal and surface formation of polysilicon was analyzed. The results showed that most of abrasives removed material with ductile removal mode, however, the volume of the material removed by abrasive in ductile mode is less than 10% of the total removal volume. Brittle fracture removal mode was still the major way of material removal in diamond wire sawing. With the same ratio of the feed rate and wire speed, the faster feed rate and wire speed will not only improve the cutting efficiency, but also is easier to obtain a brittle fracture surface. There is a critical angle θc for the distribution of abrasives on the wire saw surface. Only when the position angle of the abrasive removing material in brittle mode is less than θc, the brittle fracture can be formed on the wafers surface.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research · Force Microscopy Techniques and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Research progress on solar cell
2. S.K. Deb, Chapter 584 – recent developments in high-efficiency PV cells, in: Proceedings of the World Renewable Energy Congress VI, 2000, pp. 2658–2663.10.1016/B978-008043865-8/50584-5 ↗
3. Effect of growth rate and wafering on residual stress of diamond wire sawn silicon wafers
4. A comprehensive study on slicing processes optimization of silicon ingot for photovoltaic applications10.1016/j.solener.2017.12.040 ↗
5. Diamond wire sawing of solar silicon wafers: a sustainable manufacturing alternative to loose abrasive slurry sawing
6. A. Holt, A. Thøgersen, C. Rohr, J.I. Bye, G. Helgesen, Ø. Nordseth, S.A. Jensen, L. Norheim, Ø. Nielsen, Surface structure of mono-crystalline silicon wafers produced by diamond wire sawing and by standard slurry sawing before and after etching in alkaline solutions, in: Proceedings of the Photovoltaic Specialists Conference: 2010, pp. 003501–003504.10.1109/PVSC.2010.5614103 ↗
7. Characterization of polycrystalline silicon wafers for solar cells sliced with novel fixed‐abrasive wire10.1002/pip.923 ↗
8. Controllable nano-texturing of diamond wire sawing polysilicon wafers through low-cost copper catalyzed chemical etching10.1016/j.matlet.2018.03.092 ↗
9. Experiment study on electroplated diamond wire saw slicing single-crystal silicon10.1016/j.mssp.2016.08.003 ↗
10. Y. Gao, Y. Chen, P. Ge, L. Zhang, W. Bi, Study on the subsurface microcrack damage depth in electroplated diamond wire saw slicing SiC crystal, Ceram. Int. 〈https://doi.org/10.1016/j.ceramint.2018.09.088〉.10.1016/j.ceramint.2018.09.088 ↗
11. A review on surface texturing technology for multicrystalline silicon
12. Textural development of SiC and diamond wire sawed sc-silicon wafer10.1016/j.egypro.2012.07.072 ↗
13. Vapor etching method for diamond wire sawn multicrystalline silicon wafers
14. Research of the cutting marks on diamond wire cut multicrystalline silicon wafers and the method to remove them
15. A. Bidiville, K. Wasmer, R. Kraft, C. Ballif, Diamond wire-sawn silicon wafers from the lab to the cell production, in: Eu Pv-Sec, 2009.
16. Generation of diamond wire sliced wafer surface based on the distribution of diamond grits10.1007/s12541-014-0401-2 ↗
17. Depth of cut for single abrasive and cutting force in resin bonded diamond wire sawing10.1007/s00170-016-8896-6 ↗
18. Prediction of sawing force for single-crystal silicon carbide with fixed abrasive diamond wire saw10.1016/j.mssp.2017.01.014 ↗
19. Analytical force modeling of fixed abrasive diamond wire saw machining with application to SiC monocrystal Wafer processing10.1115/1.4034792 ↗
20. The chemo-mechanical effect of cutting fluid on material removal in diamond scribing of silicon10.1063/1.4991536 ↗
21. Ductile mode behavior of silicon during scribing by spherical abrasive particles10.1016/j.procir.2016.02.341 ↗
22. Studies of the ductile mode of cutting brittle materials (A review)10.3103/S1063457613050018 ↗
23. Effect of wear of diamond wire on surface morphology, roughness and subsurface damage of silicon wafers10.1016/j.wear.2016.07.009 ↗
24. Crystallographic orientation identification in multicrystalline silicon wafers using NIR transmission intensity10.1007/s11664-017-5982-y ↗
25. Ductile behaviour in single-point diamond-turning of single-crystal silicon10.1016/S0924-0136(02)00124-3 ↗
26. Investigation on critical crack-free cutting depth for single crystal silicon slicing with fixed abrasive wire saw based on the scratching machining experiments10.1016/j.mssp.2017.10.027 ↗
27. Distribution of diamond grains in fixed abrasive wire sawing process10.1007/s00170-014-5782-y ↗
28. Elastic/plastic indentation damage in ceramics: the lateral crack system
29. Study on cutting force model in ultrasonic vibration assisted side grinding of zirconia ceramics10.1016/j.ijmachtools.2016.01.004 ↗
30. Investigation of subsurface damage depth of single crystal silicon in electroplated wire saw Slicing10.4028/www.scientific.net/KEM.416.306 ↗
31. Depth of cut per abrasive in fixed diamond wire sawing10.1007/s00170-015-7089-z ↗
32. Effect of grit shape and crystal structure on damage in diamond wire scribing of silicon10.1111/jace.14732 ↗
33. Wear of diamond in scribing of multi-crystalline silicon10.1063/1.5037106 ↗
34. Three-dimensional shape modeling of diamond abrasive grains measured by a scanning laser microscope10.4028/www.scientific.net/KEM.238-239.131 ↗