Reduced amount of contamination particle generated by CF4/Ar/O2 plasma corrosion of Y2O3 materials: Influence of defluorination process
Source abstract
Abstract
Y 2O 3 coatings during atmospheric plasma spray (APS) processes are used to suppress the corrosion of internal process chamber parts for semiconductor plasma etching. Highly corrosive fluorine-based plasma corrodes the surface, causing contamination particle and process drift, which are the main causes of yield reduction. In this paper, defluorination is proposed to reduce the amount of contamination particle generation by removing the YO xF y layer on the surface of APS-Y 2O 3 material after plasma etching. After exposure to CF 4/Ar/O 2 plasma, chemical–mechanical polishing occurred using KOH, surfactant, and piranha solutions, respectively. The highest and lowest defluorination efficiencies were obtained with the piranha and surfactant solutions, respectively. The results were validated by field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. In particular, the piranha solution generated the lowest amount of contamination particles and lowest amount of etching. In contrast, the thickness reduction due to the defluorination process resulted in the highest breakdown voltage among the surfactant solutions, thereby prompting optimization studies. Finally, the mechanisms of the plasma etching and defluorination processes were derived, and a new method for controlling the amount of contamination particle generation was presented.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Diamond and Carbon-based Materials Research · Plasma Diagnostics and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Factor design for the oxide etching process to reduce edge particle contamination in capacitively coupled plasma etching equipment10.3390/app12115684 ↗
2. Particle contamination characterization in a helicon plasma etching tool10.1116/1.580161 ↗
3. Reduction of particle contamination in an actual plasma etching process
4. Reduction of particle contamination in plasma-etching equipment by dehydration of chamber wall, Jpn10.1143/JJAP.47.3630 ↗
5. Yield enhancement through defect reduction for post wet silicon nitride etch applications
6. Particle reduction and control in plasma etching equipment10.1109/TSM.2005.858464 ↗
7. Particle control in dielectric etch chamber10.1109/TSM.2005.863224 ↗
8. The grand challenges of plasma etching: a manufacturing perspective10.1088/0022-3727/47/27/273001 ↗
9. Inline defect control for automotive memory devices in IC manufacturing, ASMC (Advanced Semicond
10. Improvement of corrosion properties of plasma in an aluminum alloy 6061-T6 by phytic acid anodization temperature10.1016/j.jmrt.2020.12.086 ↗
11. Improvement of plasma resistance of anodic aluminum-oxide film in sulfuric acid containing cerium(IV) ion10.3390/coatings10020103 ↗
12. Surface chemical changes of aluminum during NF3-based plasma processing used for in situ chamber cleaning10.1116/1.1633566 ↗
13. Full wafer particle defect characterization
14. Yttrium oxyfluoride coatings deposited by suspension plasma spraying using coaxial feeding10.3390/coatings10050481 ↗
15. Effect of processing parameters and powder size on microstructures and mechanical properties of Y2O3 coatings fabricated by suspension plasma spray10.4191/kcers.2015.52.6.395 ↗
16. Contamination particle behavior of aerosol deposited Y2O3 and YF3 coatings under NF3 plasma10.3390/coatings9050310 ↗
17. Surface analysis of chamber coating materials exposed to CF4/O2 plasma10.3390/coatings11010105 ↗
18. Processing map to control the erosion of Y2O3 in fluorine based etching plasmas10.1111/jace.18334 ↗
19. Phase composition, structural, and plasma erosion properties of ceramic coating prepared by suspension plasma spraying10.1111/ijac.13011 ↗
20. Plasma-resistance evaluation of yttrium oxyfluoride coating prepared by aerosol deposition method10.1111/ijac.13880 ↗
21. Microstructural evolution and mechanical properties of atmospheric plasma sprayed Y2O3 coating with state of in-flight particle10.1016/j.ceramint.2020.09.246 ↗
22. Comparison of erosion behavior and particle contamination in mass-production CF4/O2 plasma chambers using Y2O3 and YF3 protective coatings10.3390/nano7070183 ↗
23. The effect of powder particle size on the corrosion behavior of atmospheric plasma spray-Y2O3 coating: unraveling the corrosion mechanism by fluorine-based plasma10.1016/j.apsusc.2022.154958 ↗
24. Continuous plasma etch process with waferless chamber clean optimization for defect reduction by eliminating center injector shading
25. Simulated covered wafer auto clean (cwac) to eliminate first wafer effect and improve process capability
26. Improved reliability of breakdown voltage measurement of yttrium oxide coatings by plasma spray10.1016/j.ceramint.2019.07.238 ↗
27. Flame-synthesized Y2O3:Tb3+ nanocrystals as spectral converting materials10.1007/s11051-018-4347-7 ↗
28. Flame synthesized Y2O3;Tb3+–Yb3+ phosphors as spectral convertors for solar cells.pdf10.1007/s11164-018-3270-y ↗
29. Microstructure characterization and nanomechanics of cold-sprayed pure Al and Al-Al2O3 composite coatings10.1016/j.surfcoat.2013.05.009 ↗
30. Granule spray process for fabrication of adherent, low thermal conductivity ceramic coatings10.1016/j.ceramint.2021.03.105 ↗
31. Room temperature impact consolidation (RTIC) of fine ceramic powder by aerosol deposition method and applications to microdevices10.1007/s11666-008-9163-7 ↗
32. An overview of the Aerosol Deposition method: process fundamentals and new trends in materials applications
33. Contamination particles and plasma etching behavior of atmospheric plasma sprayed Y2O3 and YF3 coatings under NF3 plasma
34. A study on plasma corrosion resistance and cleaning process of yttrium-based materials using atmospheric
35. CF4 decomposition in a low-pressure ICP: influence of applied power and O2 content10.1088/0022-3727/47/35/355205 ↗
36. Gas ratio effects on the Si etch rate and profile uniformity in an inductively coupled Ar/CF4 plasma
37. 2000
38. Plasma etching behavior of yof coating deposited by suspension plasma spraying in inductively coupled chf3/ar plasma10.3390/coatings10111023 ↗
39. Atomistic insights into milling mechanisms in an Fe-Y2O 3 model alloy10.1007/s00339-013-7877-y ↗
40. Preparation and characterization of sprayed-yttrium oxyfluoride corrosion protective coating for plasma process chambers10.3390/coatings8100373 ↗
41. Plasma etching behavior of SF6 plasma Pre-treatment sputter-deposited yttrium oxide films
42. Water assisted atomic layer deposition of yttrium oxide using tris(N, N ′-diisopropyl-2-dimethylamido-guanidinato) yttrium(iii): process development, film characterization and functional properties10.1039/C7RA13417G ↗
43. Sonochemical green synthesis of yttrium oxide (Y2O3) nanoparticles as a novel heterogeneous catalyst for the construction of biologically interesting 1,3-Thiazolidin-4-ones10.1007/s10562-017-2168-4 ↗
44. High critical current density of YBa2Cu3O7-x superconducting films prepared through a DUV-assisted solution deposition process
45. Elucidation of the decomposition reactions of low-fluorine YBa2Cu3O7-x precursors during film pyrolysis10.1016/j.jaap.2020.104777 ↗
46. Mechanochemical routes to functionalized graphene nanofillers tuned for lightweight carbon/hydrocarbon composites10.1002/mame.201800496 ↗
47. Role of fluorocarbon film formation in the etching of silicon, silicon dioxide, silicon nitride, and amorphous hydrogenated silicon carbide10.1116/1.1626642 ↗