Effect of cure shrinkage of epoxy molding compound on warpage behavior of semiconductor package
Source abstract
Abstract
Cure shrinkage of the epoxy molding compound (EMC) for semiconductor package during molding process, was precisely measured using a fiber Bragg grating (FBG) sensor by measuring a Bragg wavelength (BW) shift. A dielectric sensor was simultaneously used to monitor the curing process of the EMC and define its gelation point. The relationship between internal strain development of the EMC and its degree of cure was investigated by correlating two measured values (The internal strain from the FBG sensor and the degree of cure from the dielectrometry). The viscoelastic properties of the EMC were also measured by a three-point bending stress relaxation test. Finally, the warpage of EMC-aluminum bi-layer strip was measured with digital image correlation (DIC) method and compared with the result from the finite element analysis. As a result, it was confirmed that the cure shrinkage of the EMC should be considered as an important factor in predicting warpage behavior of the semiconductor.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Nanofabrication and Lithography Techniques · Epoxy Resin Curing Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. Using IoT technology for computer-integrated manufacturing systems in the semiconductor industry10.1016/j.asoc.2020.106065 ↗
2. Remeasurement dispatching rule for semiconductor EDS process
3. A fast modular semiconductor-based Marx generator for driving dynamic loads10.1109/TPS.2018.2876503 ↗
4. Study of the impact of curing condition on flexural strength of a very thin semiconductor package10.9734/jerr/2021/v20i517311 ↗
5. Material properties sensitivity analysis based on thermomechanical analysis on warpage for ball grid array semiconductor packaging
6. Review on the effects of process parameters on strength, shrinkage, and warpage of injection molding plastic component10.1080/03602559.2015.1132466 ↗
7. Measurement of elastic properties of epoxy molding compound by single cylindrical configuration with embedded fiber Bragg grating sensor10.1007/s11340-016-0215-5 ↗
8. Prediction of shrinkage and warpage in consideration of residual stress in integrated simulation of injection molding10.1016/S0263-8223(00)00045-3 ↗
9. Warpage prediction and experiments of fan-out waferlevel package during encapsulation process10.1109/TCPMT.2012.2228005 ↗
10. E.M. Graycochea Jr, F.R.I. Gomez, R.S. Rodriguez, Warpage Mitigation through Diebond Process Improvement with Enhanced Leadframe Configuration.
11. Effects of material properties on warpage in fused deposition modeling parts10.1007/s00170-017-1340-8 ↗
12. Warpage induced in bi-material specimens: coefficient of thermal expansion, chemical shrinkage and viscoelastic modulus evolution during cure10.1016/j.compositesa.2005.05.012 ↗
13. Warpage prediction methodology of extremely thin package
14. A novel integrated warpage prediction model based on characterization of viscoelasticity in time domain and chemical shrinkage for molded underfill
15. On curing-induced residual stresses after molding processes: mold shrinkage, chemical shrinkage or both?
16. An integrated warpage prediction model based on chemical shrinkage and viscoelasticity for molded underfill
17. Volumetric effective cure shrinkage measurement of dual curable adhesives by fiber Bragg grating sensor10.1007/s10853-020-04716-1 ↗
18. Characterization of effective chemical shrinkage and modulus evolution during polymerization
19. Numerical investigation and experimental validation of residual stresses building up in microelectronics packaging10.1016/j.microrel.2016.03.015 ↗
20. Generalized hybrid modeling to determine chemical shrinkage and modulus evolutions at arbitrary temperatures10.1007/s11340-013-9752-3 ↗
21. Simultaneous measurement of effective chemical shrinkage and modulus evolutions during polymerization10.1007/s11340-010-9410-y ↗
22. Thermo-optical modeling of polymer fiber Bragg grating illuminated by light emitting diode10.1016/j.ijheatmasstransfer.2007.06.038 ↗
23. Dual-configuration fiber Bragg grating sensor technique to measure coefficients of thermal expansion and hygroscopic swelling10.1007/s11340-013-9804-8 ↗
24. Integrated measurement technique for curing process-dependent mechanical properties of polymeric materials using fiber bragg grating10.1007/s11340-007-9067-3 ↗
25. Numerical modeling to evaluate the performance of FBG-based strain sensors
26. Formation and properties of thermosetting and high Tg polymeric materials10.1002/pen.760262012 ↗
27. Dielectric monitoring of cure in a commercial carbon-fibre composite10.1016/0266-3538(95)00007-0 ↗
28. Lee · 2014 · vol. 156
29. Experimental investigation of span length for flexural test of fiber reinforced polymer composite laminates10.1016/j.jmrt.2017.06.010 ↗
30. Stress relaxation test of molding compound for MEMS packaging
31. Stress relaxation in plastic molding compounds
32. Relationship between isothermal and dynamic cure of thermosets via the isoconversion representation10.1002/pen.11191 ↗
33. Brostow · 2013
34. Effect of colloidal fillers on the cross-linking of a UV-curable polymer: gel point rheology and the winter− chambon criterion10.1021/ma010281a ↗
35. The effects of silica-based fillers on the properties of epoxy molding compounds10.3390/ma12111811 ↗
36. Measurement method and apparatus for monitoring the kinetics of polymerization and crosslinking reactions by microwave dielectrometry10.1002/app.1990.070410327 ↗
37. Measurement of the degree of cure of carbon fiber epoxy composite materials10.1177/002199839603001302 ↗
38. Measurement of the degree of cure of glass fiber–epoxy composites using dielectrometry10.1016/S0924-0136(01)00657-4 ↗
39. Reduction of fabricational thermal residual stress of the hybrid co-cured structure using a dielectrometry10.1016/j.compscitech.2006.05.002 ↗
40. Brostow · 2014 · 191
41. Characterization of the rheological properties of a fast-curing epoxy-molding compound10.1122/1.550809 ↗
42. Integrated flow analysis during filling and post‐filling stage of thermoset molding
43. Dusek · 1988
44. C. Kim, S.P. Phansalkar, H.S. Lee, B. Han, Measurement of effective cure shrinkage of epoxy‐based molding compound by fiber Bragg grating sensor using two‐stage curing process, J. Appl. Polym. Sci. 51620.
45. Long-term stress relaxation prediction for elastomers using the time–temperature superposition method10.1016/j.matdes.2006.03.009 ↗
46. Chae · 2009 · 435
47. Characterization of viscoelastic behaviour of a molding compound with application to delamination analysis in IC packages
48. Experimental methodology for low temperature vibration investigations on electronic modules
49. Study of influence of mechanical property of temporary bonding adhesive on warpage of FO-WLP
50. Xia · 2014
51. Effective thermo-mechanical properties of aluminum–alumina composites using numerical approach10.1016/j.compositesb.2013.10.052 ↗
52. Cure kinetics characterization and monitoring of an epoxy resin using DSC, Raman spectroscopy, and DEA10.1016/j.compositesa.2013.01.021 ↗
53. Hu · 2009