Simulation methodology development of warpage estimation for epoxy molding compound under considerations of stress relaxation characteristics and curing conditions applied in semiconductor packaging
Source abstract
Abstract
The thermal mismatch between different components has been a serious issue in the reliability of electronic products. The effect of epoxy molding compound (EMC) on the warpage of electronic package should be considered. The finite element method (FEM) is widely adopted to predict the warpage induced by the molding process. However, no previous studies focused on the warpage during the molding process and post process. In this study, several material characteristics of the EMC, such as cure reaction, cure shrinkage, and viscoelasticity, are measured. This study analyzes the corresponding mathematical model completely and substitutes the above properties into the FEM while the process conditions are considered through measurement. A process-oriented simulation methodology is proposed, and the estimated warpage results show that the simulation methodology with stress relaxation of EMC is in good agreement with the experimental value. The characteristics of stress relaxation behavior undergoing the molding process are discussed through the evolution of warpage. The warpage is different from the two process steps at room temperature due to the stress relaxation. This study demonstrates how the conditions of the post molding cure (PMC) process affect the warpage. The warpage can decrease with the extension of PMC time but the degree of reduction has a limit.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Epoxy Resin Curing Processes · 3D IC and TSV technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Experimental verification and optimization analysis of warpage for panel-level fan-out package10.1109/TCPMT.2017.2726084 ↗
2. Compensation method for die shift caused by flow drag force in wafer-level molding process10.3390/mi7060095 ↗
3. Numerical and experimental studies of fabrication-induced thermal residual stresses in microelectronic packages10.1109/TCPMT.2021.3070893 ↗
4. Effect of boron nitride nanosheets on properties of a commercial epoxy molding compound used in fan-out wafer-level packaging10.1109/TCPMT.2020.2966714 ↗
5. Effect of epoxy mold compound and package dimensions on the thermomechanical properties of a fan-out package10.1007/s10854-020-03243-8 ↗
6. Study of a compression-molding process for ultraviolet light-emitting diode exposure systems via finite-element analysis10.3390/s17061392 ↗
7. FE simulation model for warpage evaluation of glass interposer substrate packages10.1109/TCPMT.2021.3065647 ↗
8. Warpage modeling of ultra-thin packages based on chemical shrinkage and cure-dependent viscoelasticity of molded underfill10.1109/TDMR.2019.2956646 ↗
9. Mechanism of warpage orientation rotation due to viscoelastic polymer substrates during thermal processing10.1016/j.microrel.2017.04.021 ↗
10. Characterization of linear viscoelastic behavior of epoxy molding compound subjected to uniaxial compression and hydrostatic pressure10.1109/TCPMT.2018.2856249 ↗
11. Warpage simulation for the reconstituted wafer used in fan-out wafer level packaging10.1016/j.microrel.2017.11.008 ↗
12. Viscoelastic warpage modeling of fan-out wafer-level packaging during wafer-level mold cure process10.1109/TCPMT.2020.2992041 ↗
13. Warpage characterization of molded wafer for fan-out wafer-level packaging10.1115/1.4044625 ↗
14. “Warpage and thermal characterization of fan-out wafer-level packaging,”10.1109/TCPMT.2017.2715185 ↗
15. Kinetics and thermal characterization of thermoset cure10.1002/pen.760130110 ↗
16. Study of P-V-T-C relation of EMC10.1115/1.1498266 ↗
17. Wiechert · 1889
18. Ferry · 1980
19. The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids10.1021/ja01619a008 ↗
20. The evolution of the viscoelastic retardation spectrum during the development of an epoxy resin network10.1002/polb.1991.090290104 ↗
21. “Prediction of the glass transition temperature of polymers: a model based on the principle of corresponding states,”10.1002/polb.1987.090250914 ↗
22. Observations of gelation and vitrification of a thermosetting resin during the evolution of polymerization shrinkage10.1002/marc.200500333 ↗
23. A rheological investigation of a high temperature organic gel used for water shut-off treatments10.1016/j.petrol.2007.02.010 ↗
24. Evaluation of polyacrylamide gels with accelerator ammonium salts for water shutoff in ultralow temperature reservoirs: gelation performance and application recommendations10.1016/j.petlm.2015.12.003 ↗
25. Cure kinetics modeling and cure shrinkage behavior of a thermosetting composite
26. Warpage modeling and characterization of the viscoelastic relaxation for cured molding process in fan-out packages
27. Characterization of chemical cure shrinkage of epoxy molding compound with application to warpage analysis10.1115/1.3068321 ↗
28. Warpage modeling and characterization of the cure-dependent chemical shrinkage and viscoelastic relaxation for cured molding process