journal article·2022-02

Effect and mechanism of oxidant on alkaline chemical mechanical polishing of gallium nitride thin films

Yebo Zhu, Xinhuan Niu, Ziyang Hou, Yinchan Zhang, Yunhui Shi, Ru Wang

Publisher page

Abstract

Abstract As a wide band gap semiconductor, gallium nitride (GaN) is widely used in kinds of electronic devices. With the improvement of device accuracy, the requirements for GaN surface processing efficiency and quality are getting higher and higher. However, due to the high hardness and high chemical stability of GaN, the processing is very difficult. Chemical mechanical polishing (CMP) is one of the high-precision processing method. The slurry plays a vital role in the GaN CMP process, especially the oxidant. As common oxidants, hydrogen peroxide (H2O2) and potassium persulfate (K2S2O8) are widely used, but their efficiency on typical GaN CMP still need to be promoted. A novel oxidant potassium peroxomonosulfate sulfate (2KHSO5·KHSO4·K2SO4) known as Oxone was also used to promote polishing efficiency and achieve a balance between efficiency and surface roughness (Sq). In order to explore the influence trend and mechanism of these three oxidants on polishing efficiency under different pH conditions and the same pH conditions after optimization on GaN CMP, a series of polishing, electrochemical and related test experiments as X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) were carried out. The results indicated that the CMP efficiency of these oxidants extremely affected by the pH values and their concentrations in alkaline slurry. The best pH values for CMP efficiency are 10, 10 and 8 for Oxone, H2O2 and K2S2O8, respectively. In addition, comparing the chemical characteristics of H2O2 and K2S2O8 with Oxone, mixed oxidants of H2O2 and K2S2O8 with different proportions were used and the results indicated that the mixed oxidant of H2O2 and K2S2O8 had better CMP efficiency than either H2O2 or K2S2O8. Sorting from largest to smallest, the polishing efficiency was Oxone, mixed oxidant, K2S2O8 and H2O2 while the surface roughness was K2S2O8, mixed oxidant, Oxone and H2O2. Considering typical CMP efficiency and average surface roughness, when Oxone concentration was 0.5 wt% at pH 10, the material removal rate of 247.92 nm/h and surface roughness of 0.547 nm was obtained simultaneously. Such results have important industrial application value for GaN CMP.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Semiconductor materials and devices · Advanced Surface Polishing Techniques · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. The fundamental surface science of wurtzite gallium nitride10.1016/j.surfrep.2017.05.001 ↗
2. Chemical mechanical polishing of gallium nitride with colloidal silica10.1149/2.024112jes ↗
3. Investigation on the surface characterization of Ga-faced GaN after chemical-mechanical polishing10.1016/j.apsusc.2015.02.107 ↗
4. A survey of Gallium Nitride HEMT for RF and high power applications10.1016/j.spmi.2017.05.042 ↗
5. Formation of combined partially recessed and multiple fluorinated-dielectric layers gate structures for high threshold voltage GaN-based HEMT power devices10.1016/j.sse.2015.09.006 ↗
6. Evaluation of subsurface damage in GaN substrate induced by mechanical polishing with diamond abrasives10.1016/j.apsusc.2013.12.005 ↗
7. Effect of polishing parameters on chemical mechanical planarization of c-plane (0 0 0 1) gallium nitride surface using SiO2 and Al2O3 abrasives10.1149/2.0181407jss ↗
8. Application of chemical mechanical polishing to the fabrication of VLSI circuit interconnections10.1149/1.2085872 ↗
9. Atomically smooth gallium nitride surface prepared by chemical-mechanical polishing with different abrasives10.1177/1350650114535383 ↗
10. Atomically smooth gallium nitride surface prepared by chemical-mechanical polishing with S2O82−-Fe2+ based slurry10.1016/j.triboint.2016.09.037 ↗
11. Effect of surfactant and electrolyte on surface modification of c-plane GaN substrate using chemical mechanical planarization (CMP) process10.1016/j.colsurfa.2016.02.035 ↗
12. Effect of surfactant based abrasive free slurry on CMP polishing rate and planarization of semi-polar (11‒22) GaN surface10.1149/2.0171905jss ↗
13. Effect of photocatalytic oxidation technology on GaN CMP10.1016/j.apsusc.2015.11.062 ↗
14. Photoelectrochemical mechanical polishing method for n-type gallium nitride10.1016/j.cirp.2019.04.121 ↗
15. Photoelectrochemically combined mechanical polishing of n-type gallium nitride wafer by using metal nanoparticles as photocathodes10.1007/s00170-018-03279-5 ↗
16. The use of potassium peroxidisulphate and Oxone® as oxidizers for the chemical mechanical polishing of silicon wafers10.1016/j.wear.2013.03.030 ↗
17. Chemical mechanical planarization of ruthenium with oxone as oxidizer10.1149/2.005203esl ↗
18. Chemical mechanical planarization of germanium using oxone((R)) based silica slurries10.1016/j.wear.2016.11.030 ↗
19. Heat-activated persulfate oxidation of atrazine: implications for remediation of groundwater contaminated by herbicides10.1016/j.cej.2014.10.097 ↗
20. Activation of persulfate (PS) and peroxymonosulfate (PMS) and application for the degradation of emerging contaminants10.1016/j.cej.2017.11.059 ↗
21. Activation of peroxymonosulfate by base: implications for the degradation of organic pollutants10.1016/j.chemosphere.2016.02.089 ↗
22. Activation of peroxymonosulfate by benzoquinone: a novel nonradical oxidation process10.1021/acs.est.5b03595 ↗
23. Improvement in chemical mechanical polishing of 4H-SiC wafer by activating persulfate through the synergistic effect of UV and TiO210.1016/j.jmatprotec.2021.117150 ↗
24. Tribo-corrosion of materials: interplay between chemical, electrochemical, and mechanical reactivity of surfaces10.1016/j.wear.2006.03.027 ↗
25. An XPS study of GaN thin films on GaAs10.1002/sia.740160116 ↗
26. Investigation of HCl-based surface treatment for GaN devices10.1063/1.4941210 ↗
27. PL and XPS study of radiation damage created by various slow highly charged heavy ions on GaN epitaxial layers10.1016/j.nimb.2011.08.001 ↗
28. Angular dependent XPS study of surface band bending on Ga polar n-GaN10.1016/j.apsusc.2018.01.196 ↗