journal article·2019-04Open access

Surface quality evaluation of single crystal 4H-SiC wafer machined by hybrid laser-waterjet: Comparing with laser machining

Shaochuan Feng, Chuanzhen Huang, Jun Wang, Zhixin Jia

Abstract

Single crystal silicon carbide (SiC), as a 3rd generation semiconductor material, has a wide application range and development prospect, especially in some key fields such as defense and aerospace industries. It's a typical difficult-to-machine and hard-brittle material due to its high hardness and brittleness . A hybrid laser-waterjet micromachining technology was employed to implement near damage-free and high-efficient micromachining of single crystal SiC. The workpiece material is heated by laser to a temperature near but below its melting point. The material is under an extremely “softened” but still solid status. A waterjet is applied off-axially to expel the heating-softened material and cool the material to eliminate thermal damage. It combines the advantages of laser processing with those of waterjet cutting. Moreover, it's a green machining approach, which is pollution-free and recyclable. In the present study, the surface quality of single crystal 4H-SiC machined by the hybrid laser-waterjet is evaluated and compared with that machined by laser. Among the wafers respectively machined by laser, under-water laser, waterjet-assisted laser and the hybrid laser-waterjet, the one machined by the hybrid laser-waterjet is with the best surface quality. Its cut boundaries between the machined area and the unmachined area are clear, the cut edges are straight, also the cut sides are clean. On the contrary, there is severe thermal damage along the cut edges and cut sides of laser machining . The microgrooves obtained from the hybrid laser-waterjet micromachining are with V-shaped cross-sections and the transition between the cut edge and the unmachined surface is flat and smooth. The cross-section profile of the microgroove machined by laser is M-shaped and there are obvious humps along the two sides of the microgroove. The microgroove bottom is almost at the same height with the unmachined surface. Besides, there are HAZs with a width of 50–100 µm and scaly recast layers on the sides of the cut machined by laser. In contrast, there is no recast layer and HAZ on the cut side of the hybrid laser-waterjet micromachining. The texture of the cut sidewall is clear and with the typical features of the material removed under the plastic mode. The EDS results show that the oxidation behavior happens during both the hybrid laser-waterjet micromachining and laser machining . However, the content of silicon dioxide generated in the hybrid laser-waterjet micromachining process (the oxygen content is about 5%) is obviously lower than that generated in laser machining (the oxygen content is more than 30%).
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Diamond and Carbon-based Materials Research · Advanced Machining and Optimization Techniques · Laser Material Processing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Silicon carbide as a new MEMS technology10.1016/S0924-4247(99)00335-0 ↗
2. Status of silicon carbide (SiC) as a wide-bandgap semiconductor for high-temperature applications: a review10.1016/0038-1101(96)00045-7 ↗
3. Towards a unified view of polytypism in silicon carbide
4. Wetting behavior of water on silicon carbide polar surfaces10.1039/C6CP04686J ↗
5. Recent advances in 4H-SiC epitaxy for high-voltage power devices10.1016/j.mssp.2017.11.003 ↗
6. Large-band-gap SiC, III-V nitride, and II-VI ZnSe-based semiconductor device technologies10.1063/1.358463 ↗
7. Impact of silicon carbide semiconductor technology in photovoltaic energy system10.1016/j.rser.2015.10.161 ↗
8. Physics of group IV elements and III-V compounds
9. A.K. Agarwal, An overview of SiC power devices, in: Proceedings of the 2010 International Conference on Power Control and Embedded System, 2010, pp. 1–4. doi:10.1109/ICPCES.2010.5698670.10.1109/ICPCES.2010.5698670 ↗
10. 4H-SiC power devices for use in power electronic motor control10.1016/S0038-1101(98)00212-3 ↗
11. SiC power devices for high voltage applications10.1016/S0921-5107(98)00528-5 ↗
12. M. Ostling, R. Ghandi, C.-M. Zetterling, SiC power devices – present status, applications and future perspective, in: Proceedings of the 2011 IEEE 23rd International Symposium on Power Semiconductor Devices ICs (ISPSD), 2011, pp. 10–15. doi:10.1109/ISPSD.2011.5890778.10.1109/ISPSD.2011.5890778 ↗
13. Temperature-dependent infrared optical properties of 3C-, 4H- and 6H-SiC10.1016/j.physb.2018.02.023 ↗
14. Advanced processing for mobility improvement in 4H-SiC MOSFETs: a review10.1016/j.mssp.2017.10.030 ↗
15. Silicon carbide MEMS for harsh environments10.1109/5.704265 ↗
16. Temperature dependence of Fowler-Nordheim current in 6H- and 4H-SiC MOS capacitors10.1109/55.644081 ↗
17. UV nanosecond laser machining and characterization for SiC MEMS sensor application10.1016/j.sna.2018.04.029 ↗
18. Experimental investigations of CO2 laser cut quality: a review
19. Laser beam machining – a review10.1016/j.ijmachtools.2007.10.017 ↗
20. Laser machining of structural ceramics – a review10.1016/j.jeurceramsoc.2008.11.010 ↗
21. Characteristics of spatter formation under the effects of different laser parameters during laser drilling10.1016/S0924-0136(01)00910-4 ↗
22. Effects of assist gas on the physical characteristics of spatter during laser percussion drilling of NIMONIC 263 alloy10.1016/S0169-4332(99)00427-4 ↗
23. Laser-induced surface drilling of silicon carbide10.1016/S0169-4332(01)00330-0 ↗
24. Laser micro machining of 3C-SiC single crystals10.1016/j.mee.2006.01.064 ↗
25. Laser ablation of titanium alloy under a thin and flowing water layer10.1016/j.ijmachtools.2014.10.013 ↗
26. Laser ablation at solid–liquid interfaces: an approach from optical emission spectra10.1063/1.481465 ↗
27. Laser ablation of solid substrates in a water-confined environment10.1063/1.1400086 ↗
28. Water-assisted laser thermal shock machining of alumina10.1016/j.ijmachtools.2007.04.003 ↗
29. Underwater-laser drilling of aluminum10.1007/s00170-013-5141-4 ↗
30. Investigation of underwater laser drilling for brittle substrates10.1016/j.jmatprotec.2008.06.057 ↗
31. B. Richerzhagen, M. Kutsuna, H. Okada, T. Ikeda, 2003. Waterjet-guided laser processing, in: I. Miyamoto, K.F. Kobayashi, K. Sugioka, R. Poprawe, H. Helvajian (Eds.), Proceedings of the SPIE, Osaka, pp. 91–94. doi:10.1117/12.486514.10.1117/12.486514 ↗
32. Design and validation of a hybrid laser/water-jet machining system for brittle materials10.2351/1.2900554 ↗
33. Kalyanasundaram · 2009
34. An investigation of hybrid laser – waterjet ablation of silicon substrates10.1016/j.ijmachtools.2012.01.002 ↗
35. Material removal of single crystal 4H-SiC wafers in hybrid laser-waterjet micromachining process10.1016/j.mssp.2018.03.035 ↗
36. Investigation and modelling of hybrid laser-waterjet micromachining of single crystal SiC wafers using response surface methodology10.1016/j.mssp.2017.05.029 ↗
37. Çengel · 2014
38. Nanostructures on SiC surface created by laser microablation10.1016/j.apsusc.2007.08.048 ↗