An investigation of recast behavior in laser ablation of 4H-silicon carbide wafer
Source abstract
Abstract
Abstract 4H-silicon carbide (SiC) is a suitable semiconductor material for high-speed power devices but also a typical difficult-to-process and hard-brittle material. Laser ablation is an efficient approach to process SiC. However, recast layer is an inevitable thermal damage during laser ablation. The present study experimentally and numerically investigated the recast behavior in laser ablation of 4H–SiC. The recast humps are with height of 1.4–3.3 μm and width of 12–22 μm, consist of SiC, Si, and SiO2, where 15.08 wt% of oxygen is detected. Microcracks and pore clusters are observed on the recast humps under SEM. Recoil pressure and surface tension in the molten pool dominate the process of recast hump formation. The recoil pressure of Si vapor is 2.27 MPa at 5000 K, as high as 22 times of atmospheric pressure. The simulation results show that the fluid in the middle flows around while the surrounding fluid flows upwards. The upward flow is almost laminar while the flow at the bottom of the molten pool is turbulent entertaining air and forming bubbles. The vaporization-induced keyhole in the molten pool becomes deeper and the sidewall becomes more inclined over time, accompanying with the “growing” of the recast hump. There are mainly three reasons causing the increase of recast height and recast width with the increased average laser power: (a) increase of recoil pressure; (b) increase of temperature gradient in the molten pool, enhancing the Marangoni convection; and (c) enlarging the molten pool and leading to more materials melting. With the decrease of the laser scanning speed, more liquid molten material is evaporated in the molten pool instead of being ejected outward to form recast humps. The increase of the laser pulse frequency decreases the peak laser intensity and hence results in the decrease of the recoil pressure. Besides, it also leads to the weakening of the heating ability of laser and lessening of the liquid molten material that could be ejected.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Laser-induced spectroscopy and plasma · Laser Material Processing Techniques · Diamond and Carbon-based Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Large-band-gap SiC, III-V nitride, and II-VI ZnSe-based semiconductor device technologies10.1063/1.358463 ↗
2. Impact of silicon carbide semiconductor technology in photovoltaic energy system10.1016/j.rser.2015.10.161 ↗
3. Physics of group IV elements and III-V compounds
4. Harris · 1995
5. Laser micro machining of 3C-SiC single crystals10.1016/j.mee.2006.01.064 ↗
6. Laser ablation and laser-hybrid ablation processes: a review10.1080/10426914.2015.1048359 ↗
7. Experimental investigation on laser micromilling of SiC microchannels
8. Excimer laser ablation of single crystal 4H-SiC and 6H-SiC wafers10.1007/s10853-010-4920-7 ↗
9. UV nanosecond laser machining and characterization for SiC MEMS sensor application10.1016/j.snb.2018.01.139 ↗
10. Ablation threshold measurements and surface modifications of 193 nm laser irradiated 4H-SiC10.1016/j.cplett.2018.09.057 ↗
11. Investigation on the laser ablation of SiC ceramics using micro‐Raman mapping technique10.1007/s40145-016-0197-x ↗
12. A study of near-infrared nanosecond laser ablation of silicon carbide10.1016/j.ijheatmasstransfer.2013.06.050 ↗
13. Laser ablation of 6H-SiC single crystals and spectral characterization
14. Laser-induced surface drilling of silicon carbide10.1016/S0169-4332(01)00330-0 ↗
15. Surface quality evaluation of single crystal 4H-SiC wafer machined by hybrid laser-waterjet: comparing with laser machining10.1016/j.mssp.2018.12.037 ↗
16. Laser micromachining of silicon in air and ice layer10.1016/j.jmapro.2018.10.008 ↗
17. Improving cutting quality by analysis of microstructure characteristics and solidification behaviour of recast layer formation on laser cut ceramic10.1016/j.jeurceramsoc.2012.03.020 ↗
18. Modelling the influence of laser drilled recast layer thickness on the fatigue performance of CMSX-410.1016/j.promfg.2018.10.173 ↗
19. Prediction modelling of recast layer and circularity for laser drilling of polyethylene terephthalate (PETG) thermoplastic10.1016/j.proeng.2017.04.086 ↗
20. Evolution of surface topography in one-dimensional laser machining of structural alumina10.1016/j.jeurceramsoc.2012.06.015 ↗
21. One-dimensional multipulse laser machining of structural alumina: evolution of surface topography10.1007/s00170-012-4709-8 ↗
22. Laser machining of structural alumina: influence of moving laser beam on the evolution of surface topography10.1111/ijac.12223 ↗
23. The role of recoil pressure in energy balance during laser materials processing10.1088/0022-3727/30/18/008 ↗
24. Effect of surface tension on melt pool dynamics during laser pulse interaction10.1088/0022-3727/39/3/025 ↗
25. Numerical simulation of melt hydrodynamics induced hole blockage in Quasi-CW fi ber laser micro-drilling of TiAl6V410.1016/j.jmatprotec.2018.06.038 ↗
26. An analytical model for the prediction of temperature distribution and evolution in hybrid laser-waterjet micro-machining10.1016/j.precisioneng.2016.07.002 ↗
27. Heating and material removal process in hybrid laser-waterjet ablation of silicon substrates10.1016/j.ijmachtools.2013.12.003 ↗
28. Nanostructures on SiC surface created by laser microablation10.1016/j.apsusc.2007.08.048 ↗
29. Computational approach to photonic drilling of silicon carbide10.1007/s00170-009-2004-0 ↗
30. Vaporization of metal absorbing laser radiation
31. Surface tension of liquid silicon10.1007/s11236-005-0043-2 ↗
32. Explosive change in crater properties during high power nanosecond laser ablation of silicon10.1063/1.373865 ↗
33. Multiphysics theoretical evaluation of thermal stresses in laser machined structural alumina10.1007/s40516-014-0004-x ↗