Numerical analysis of electron and hole transport layer engineering in MASnBr₃-based perovskite solar cells via SCAPS-1D simulation
Source abstract
Abstract
Lead-free perovskite solar cells represent a sustainable alternative toward toxic lead-based devices. However, the performance of lead-free perovskites has often been challenged due to interfacial losses and instability. Therefore, in this manuscript, SCAPS-1D simulation is conducted in a high-performance lead-free device configuration of FTO/IGZO/MASnBr 3 /CBTS/Ni to gain insight into the role of transport layers and defect control on photovoltaic behavior. An amorphous IGZO electron transport layer is adopted to enable efficient charge extraction with superior optical transparency, while Cu 2 BaSnS 4 acts as an environmentally benign hole transport layer, offering good valence-band alignment with MASnBr 3 . By means of absorber thickness, defect density, and interface recombination velocity parametric optimization, the simulation study revealed that reduction of defect density below 1 × 10 16 cm −3 and optimization of the absorber at ∼900 nm not only enhanced the charge separation but also suppressed nonradiative recombination. The highest PCE of 32.18%, with Voc = 1.1216 V, Jsc = 32.23 mA cm −2 , and fill factor = 89.02%, was realized from this optimized configuration. The synergistic adoption of IGZO and CBTS has thus been addressed, which promotes carrier extraction and stability, hence representing this heterostructure as a promising pathway toward efficient, thermally stable, and nontoxic lead-free perovskite photovoltaics.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Perovskite Materials and Applications · Chalcogenide Semiconductor Thin Films · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. Perovskite solar cells: Progress, challenges, and future avenues to clean energy10.1016/j.solener.2024.113205 ↗
2. Revolutionizing light capture: a comprehensive review of back-contact perovskite solar cell architectures10.1016/j.mattod.2025.08.017 ↗
3. Band gap tuning of perovskite solar cells for enhancing the efficiency and stability: issues and prospects10.1039/D4RA01640H ↗
4. Stability and reliability of perovskite containing solar cells and modules: degradation mechanisms and mitigation strategies10.1039/D4EE01898B ↗
5. Effect of graded double perovskite for boosting up the photovoltaic output parameters of solar cell: a numerical modelling using SCAPS-1D10.21272/jnep.15(6).06002 ↗
6. Mitigating lead toxicity in halide perovskite solar cells: strategies for sustainable development10.3390/inorganics13040123 ↗
7. The toxicity of lead and lead-free perovskite precursors and nanocrystals to human cells and aquatic organisms
8. Functional layers in efficient and stable inverted tin-based perovskite solar cells10.1016/j.joule.2023.08.002 ↗
9. Perovskite solar cells: a review of the latest advances in materials, fabrication techniques, and stability enhancement strategies10.3390/mi15020192 ↗
10. Instability of tin iodide perovskites: bulk p-doping versus surface tin oxidation10.1021/acsenergylett.0c01174 ↗
11. Strategies to improve performance and stability for tin-based perovskite solar cells10.1021/acsenergylett.9b01179 ↗
12. C. Frasca, P. Alippi, R. Schwiddessen, K. Prashanthan, G. Nasti, S. Zuo, M. Okash Ur Rehman, M.H. Aldamasy, N.T. Putri Hartono, A. Musiienko, A. Abate, Mitigation of self-p-doping and off-centering effect in tin perovskite via strontium doping, ACS Energy Lett. 10 (2025) 526–533. doi:https://doi.org/10.1021/acsenergylett.4c02974.10.1021/acsenergylett.4c02974 ↗
13. L. McGovern, M.H. Futscher, L.A. Muscarella, B. Ehrler, Understanding the stability of MAPbBr3 versus MAPbI3: Suppression of methylammonium migration and reduction of Halide migration, J. Phys. Chem. Lett. 11 (2020) 7127–7132. doi:https://doi.org/10.1021/acs.jpclett.0c01822.10.1021/acs.jpclett.0c01822 ↗
14. M. Shah, I. Ahmad, J. Ullah, K. Hayat, M. Munawar, M. Mushtaq, A. Shah, S.K. Shah, First-Principles insights and SCAPS-1D simulations for optimizing MASnBr3-based perovskite solar cells, Comput. Mater. Sci. 250 (2025) 113699. doi:https://doi.org/10.1016/j.commatsci.2025.113699.10.1016/j.commatsci.2025.113699 ↗
15. M. Haneef, S. Tahir, H.A. Mahmoud, A. Ali, A. Ashfaq, Optimizing Lead-free MASnBr3 Perovskite Solar Cells for High-Efficiency and Long-Term Stability Using Graphene and Advanced Interface Layers, ACS Omega 9 (2024) 7053–7060. doi:https://doi.org/10.1021/acsomega.3c08981.10.1021/acsomega.3c08981 ↗
16. K. Dris, M. Benhaliliba, Study and optimization of a new perovskite solar cell structure based on the two absorber materials Cs2TiBr6 and MASnBr3 using SCAPS 1D, Period. Polytech. Chem. Eng. 68 (2024) 348–363. doi:https://doi.org/10.3311/ppch.36825.10.3311/PPch.36825 ↗
17. M. Ghaleb, A. Arrar, A. Hadji Chikh, H. Bendjilali, O. Zerrouki, I-MASnBr3/CZTGS Heterojunction Solar Cell Layer Optimization Investigated Using Scaps-1D Software Exhibited Excellent Performance at 50%, Annals of West University of Timisoara - Physics 66 (2024) 191–214. doi:https://doi.org/10.2478/awutp-2024-0012.10.2478/awutp-2024-0012 ↗
18. Md.M. Hasan, Mst.A. Siddika, Md.F. Ali, Md.R.I. Sheikh, A. Al Mamun, M.J. Hossen, Next-generation lead-free solar cells with MASnBr3/ZnSnN2 dual absorbers for high efficiency, Front. Mater. Volume 12–2025 (2025). https://doi.org/10.3389/fmats.2025.1652733.10.3389/fmats.2025.1652733 ↗
19. Efficient planar perovskite solar cells with ZnO electron transport layer10.3390/coatings12121981 ↗
20. IGZO-based electronic device application: advancements in gas sensor, logic circuit, biosensor, neuromorphic device, and photodetector technologies10.3390/mi16020118 ↗
21. Role of interface engineering in amorphous InGaZnO ETL for non-fullerene organic solar cells
22. Probing the reactivity of ZnO with perovskite precursors10.1021/acsami.4c01945 ↗
23. Highly stable perovskite light-emitting diodes10.1016/j.matt.2023.11.022 ↗
24. Thermal stability-enhanced and high-efficiency planar perovskite solar cells with interface passivation10.1021/acsami.7b10994 ↗
25. Investigation of the performance of perovskite solar cells with ZnO-covered PC61BM electron transport layer10.3390/ma16145061 ↗
26. Self-assembled monolayers for perovskite solar cells
27. Improving the stability of inverted perovskite solar cells towards commercialization10.1038/s43246-022-00291-x ↗
28. The damaging effects of the acidity in PEDOT: PSS on semiconductor device performance and solutions based on non-acidic alternatives10.1039/C9MH01978B ↗
29. Enhanced water resistance of PEDOT: PSS through crosslinking agent incorporation for efficient and stable organic solar cells10.1007/s40843-024-3273-2 ↗
30. Simultaneously enhancing the efficiency and stability of perovskite solar cells by using P3HT/PEDOT: PSS as a double hole transport layer10.3390/nano14181476 ↗
31. Fabrication of efficient and stable planar perovskite solar cell using copper oxide as hole transport material10.1016/j.jallcom.2022.166285 ↗
32. Solution-processed CuOx as an efficient hole-extraction layer for inverted planar heterojunction perovskite solar cells10.1016/j.cclet.2016.06.021 ↗
33. Solution-processed CuOx as an efficient hole-extraction layer for inverted planar heterojunction perovskite solar cells10.1016/j.cclet.2016.06.021 ↗
34. Colloidal synthesis, optical properties, and hole transport layer applications of Cu2BaSnS4 (CBTS) nanocrystals10.1021/acsaem.9b00473 ↗
35. M. Haneef, S. Tahir, H.A. Mahmoud, A. Ali, A. Ashfaq, Optimizing Lead-free MASnBr3 Perovskite Solar Cells for High-Efficiency and Long-Term Stability Using Graphene and Advanced Interface Layers, ACS Omega 9 (2024) 7053–7060. doi:https://doi.org/10.1021/acsomega.3c08981.10.1021/acsomega.3c08981 ↗
36. SCAPS-1D device simulation of highly efficient perovskite solar cells using diverse charge transport layers10.1007/s11664-023-10681-7 ↗
37. Simulation and optimization of 30.17% high performance n-type TCO-free inverted perovskite solar cell using inorganic transport materials10.1038/s41598-024-62882-7 ↗
38. Modelling polycrystalline semiconductor solar cells10.1016/S0040-6090(99)00825-1 ↗
39. Simulation and optimization of lead-free CH3NH3SnI3 perovskite solar cells using SCAPS-1D10.1016/j.rio.2025.100823 ↗
40. Optimization of lead-free perovskite solar cells in normal-structure with WO3 and water-free PEDOT: PSS composite for hole transport layer by SCAPS-1D simulation10.1016/j.optmat.2021.111432 ↗
41. L. You, X. Zhang, Q. Ma, W. Zhu, J. Wu, Optimization of electron transport layer-free cs2TiBr6/MASnBr3 laminated structure perovskite solar cells by SCAPS-1D simulation, Phys. Status Solidi (a) 220 (2023). doi:https://doi.org/10.1002/pssa.202300071.10.1002/pssa.202300071 ↗
42. M. Ghaleb, A. Arrar, Z. Touaa, Optimization and Performance Analysis of a TiO2/i-CH3NH3SnBr3/CsPbI3/Al(BSF) Heterojunction Perovskite Solar Cell for Enhanced Efficiency, ACS Omega 8 (2023) 37011–37022. doi:https://doi.org/10.1021/acsomega.3c03891.10.1021/acsomega.3c03891 ↗
43. Numerical optimization and efficiency analysis of sn-based perovskite-on-silicon tandem solar cells with various TCO materials using SCAPS-1D simulation10.1063/5.0217477 ↗
44. Advances in lead-free perovskite solar cell design via SCAPS-1D simulations10.1039/D5SU00526D ↗
45. G.M. Mustafa, B. Younas, S. Saba, Z.M. Elqahtani, N. Alwadai, S. Aftab, Numerical simulation to optimize power conversion efficiency of an FTO/GO/Cs2AgBiBr6/Cu2O solar cell, RSC Adv. 14 (2024) 18957–18969. doi:https://doi.org/10.1039/D4RA01559B.10.1039/D4RA01559B ↗
46. An extensive study on multiple ETL and HTL layers to design and simulation of high-performance lead-free CsSnCl3-based perovskite solar cells10.1038/s41598-023-28506-2 ↗
47. M. Haneef, S. Tahir, H.A. Mahmoud, A. Ali, A. Ashfaq, Optimizing Lead-free MASnBr3 Perovskite Solar Cells for High-Efficiency and Long-Term Stability Using Graphene and Advanced Interface Layers, ACS Omega 9 (2024) 7053–7060. doi:https://doi.org/10.1021/acsomega.3c08981.10.1021/acsomega.3c08981 ↗
48. Defect study and modelling of SnX3-based perovskite solar cells with SCAPS-1D10.3390/nano11051218 ↗
49. Investigating the impact of MASNBR 3 absorbent layer thickness on FTO/TiO 2/MASnBr 3/CuI perovskite solar cells characteristics10.15251/DJNB.2024.192.707 ↗
50. K. M V, C. Anjali, K. Sudheer, Device simulation and optimization of HTL-free perovskite solar cell with CH 3 NH 3 SnBr 3 as the absorber layer using solar cell capacitance simulator software, J. Ovonic Res. (2024), 20 (2), 245–254. doi:10.15251/JOR.2024.202.245.10.15251/JOR.2024.202.245 ↗
51. Hasan · 2025
52. Deep insights into the coupled optoelectronic and photovoltaic analysis of Lead-free CsSnI₃ perovskite-based solar cell using DFT calculations and SCAPS-1D simulations10.1021/acsomega.3c00306 ↗
53. M.K. Hossain, D.P. Samajdar, R.C. Das, A.A. Arnab, M.F. Rahman, M.H.K Rubel, M.R. Islam, H. Bencherif, R. Pandey, J. Madan, M.K. Mohammed, Design and simulation of Cs₂BiAgI₆ double perovskite solar cells with different electron transport layers for efficiency enhancement. Energy Fuel (2023), 37 (5), 3957–3979.10.1021/acs.energyfuels.3c00181 ↗