journal article·2025-12Open access

Growth and characterization of orthorhombic cesium lead tri-iodide perovskite thin-films by sequential physical vapor deposition for solar cells

Sizwe Sibiya, Mmantsae Diale

Abstract

• Sequential physical vapor deposition of CsPbI 3 has been demonstrated. • Films exhibited large average crystallites and uniform surface coverage with polycrystalline grains. • Devices delivered PCEs correlating to the density of trap states. This study used the sequential physical vapor deposition (SPVD) technique to grow poly-crystalline yellow phase cesium lead triiodide (γ-CsPbI 3 ). The effect of CsI thickness on structural, optical, morphological, and electrical properties of γ-CsPbI 3 was investigated. Crystallographic parameters of γ-CsPbI 3 as-deposited and 100 °C annealed pure-phase were determined using X-ray diffraction (XRD). Computed lattice constants were a = 4.88, b = 9.96, and c = 16.5 Å, with an average crystallite size increasing from 170 − 243 nm, and micro-strain decreasing with an increase of cesium iodide (CsI) thickness from 200 to 500 nm. Field-emission scanning electron microscopy (FE-SEM) images showed uniform surface coverage with polycrystalline grains. Average grain size increased from 168 to 235 nm with increasing CsI thickness, resulting in large, pinhole-free, and tightly packed grains. Furthermore, atomic force microscopy (AFM) surface analysis demonstrated a reduction in surface roughness from 44.0 to 38.3 nm as CsI thickness increased from 200 to 500 nm. The ultraviolet–visible (UV–Vis) spectra showed an increase in bandgap from 2.24 to 2.38 eV for as-deposited and a decrease from 2.37 to 2.05 eV for annealed films as the thickness of CsI increased. Current–voltage (J-V) measurements revealed a correlation between the trap-filled limit voltage (V TFL ) and defect density. For electron-only devices with film thicknesses of 300, 400, 500, and 600 nm, the trap state densities were found to be 1.40 × 10 15 , 1.95 × 10 15 , 2.12 × 10 15 , and 2.39 × 10 15 cm −3 , respectively. The corresponding electron mobilities were 2.34 × 10 1 , 6.30 × 10 1 , 4.72 × 10 2 , and 1.07 × 10 2 cm 2 /V·s. Additionally, perovskite solar cells (PSCs) fabricated under ambient air conditions revealed an improvement in power conversion efficiency (PCE) from 2.0 to 4.93 % for the FTO/c-TiO 2 /CsPbI 3 /Au architecture. This work suggests a way of improving precursor’s reaction using SPVD by controlling the film thickness, reducing defect density through SPVD, and therefore highlighting film thickness optimization in perovskites.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Perovskite Materials and Applications · Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. Organometallic halide perovskites: sharp optical absorption edge and its relation to photovoltaic performance10.1021/jz500279b ↗
2. Impact of small phonon energies on the charge-carrier lifetimes in metal-halide perovskites10.1021/acs.jpclett.7b03414 ↗
3. Infrared dielectric screening determines the low exciton binding energy of metal-halide perovskites10.1021/acs.jpclett.7b03286 ↗
4. Tunable wide‐bandgap monohalide perovskites10.1002/adom.202000423 ↗
5. Enhancing electron diffusion length in narrow-bandgap perovskites for efficient monolithic perovskite tandem solar cells10.1038/s41467-019-12513-x ↗
6. Interphases, interfaces, and surfaces of active materials in rechargeable batteries and perovskite solar cells10.1002/adma.201905245 ↗
7. Challenges and opportunities for CsPbBr3 perovskites in low-and high-energy radiation detection10.1021/acsenergylett.1c00007 ↗
8. Volatile organic compound gas sensors based on methylammonium lead iodide perovskite operating at room temperature10.1039/C9RA10703G ↗
9. Efficient perovskite solar cells via improved carrier management10.1038/s41586-021-03285-w ↗
10. Stability and performance enhancement of perovskite solar cells: a review10.3390/en16104031 ↗
11. Enhancement in lifespan of halide perovskite solar cells10.1039/C8EE02852D ↗
12. Surface degradation mechanism on CH3NH3PbBr3 hybrid perovskite single crystal by a grazing E-beam irradiation10.3390/nano10071253 ↗
13. Effect of relative humidity during the preparation of perovskite solar cells: performance and stability10.1016/j.solener.2020.02.052 ↗
14. High‐quality Ruddlesden–Popper perovskite film formation for high‐performance perovskite solar cells10.1002/adma.202002582 ↗
15. A silicon-on-insulator slab for topological valley transport10.1038/s41467-019-08881-z ↗
16. Structural and doping effects in the half-metallic double perovskite A 2 CrWO 6 (A= Sr, Ba, and Ca)10.1103/PhysRevB.68.144431 ↗
17. CsPb0. 9Sn0. 1IBr2 based all-inorganic perovskite solar cells with exceptional efficiency and stability10.1021/jacs.7b07949 ↗
18. Optimizing excited charge dynamics in layered halide perovskites through compositional engineering10.1021/acs.nanolett.5c01223 ↗
19. Chlorine doping for black γ-CsPbI3 solar cells with stabilized efficiency beyond 16%10.1016/j.nanoen.2019.01.034 ↗
20. Prospects for commercialization of CsPbIBr2‐based all‐inorganic perovskite solar cells: fabrication, stability, and engineering strategies10.1002/adfm.202503508 ↗
21. Influence of phase transition on stability of perovskite solar cells under thermal cycling conditions10.1016/j.solener.2019.06.025 ↗
22. Scaling behavior of moisture-induced grain degradation in polycrystalline hybrid perovskite thin films10.1039/C6EE02941H ↗
23. Simultaneous evolution of uniaxially oriented grains and ultralow-density grain-boundary network in CH3NH3PbI3 perovskite thin films mediated by precursor phase metastability10.1021/acsenergylett.7b00980 ↗
24. The role of grain boundaries in perovskite solar cells10.1002/aenm.201901489 ↗
25. Advancements in configuration structures and fabrication techniques for achieving stability in perovskite solar cells: a comprehensive review10.1007/s43207-024-00401-0 ↗
26. Exceeding 23% efficiency for 3D/3D bilayer Perovskite heterojunction MAPbI3/FAPbI3‐based hybrid perovskite solar cells with enhanced stability10.1002/adfm.202408721 ↗
27. Effects of hydroiodic acid concentration on the properties of CsPbI3 perovskite solar cells10.1021/acsomega.8b01589 ↗
28. Unlocking all-perovskite tandem solar cells to∼ 30% efficiency: a simulation and optimization approach with MPA2FPh-BT-BA as a hole selective contact10.1007/s12596-025-02449-5 ↗
29. Over 24% efficient MA-free CsxFA1− xPbX3 perovskite solar cells10.1016/j.joule.2022.05.002 ↗
30. Enhanced the efficiency of TMs (Co and Ag) doped lead based mixed halides perovskite solar cells through the conduction band gap engineering10.1016/j.jics.2025.101618 ↗
31. Caesium for perovskite solar cells: an overview10.1002/chem.201801096 ↗
32. Co-evaporation of CH3NH3PbI3: how growth conditions impact phase purity, photostriction, and intrinsic stability10.1021/acsami.0c19038 ↗
33. All-evaporated, all-inorganic CsPbI3 Perovskite-based devices for broad-band photodetector and solar cell applications10.1021/acsaelm.1c00252 ↗
34. Impact of dynamic co-evaporation schemes on the growth of methylammonium lead iodide absorbers for inverted solar cells10.1038/s41598-022-23132-w ↗
35. Precise control of PbI2 excess into grain boundary for efficacious charge extraction in off-stoichiometric perovskite solar cells10.1016/j.electacta.2020.135697 ↗
36. Pb clustering and PbI2 nanofragmentation during methylammonium lead iodide perovskite degradation10.1038/s41467-019-09909-0 ↗
37. Intrinsic defects on α, γ and δ-CsPbI 3 (001) surfaces and implications for the α/γ to δ phase transition10.1039/D3CP00285C ↗
38. Extremely low trap-state energy level perovskite solar cells passivated using NH 2-POSS with improved efficiency and stability10.1039/C7TA11345E ↗
39. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray debye-scherrer spectrum10.1080/14786435608238074 ↗
40. Effect of dislocation density on the epitaxial growth of silver10.1063/1.1709890 ↗
41. Understanding the role of cesium and rubidium additives in perovskite solar cells: trap states, charge transport, and recombination
42. Selective stabilization and photophysical properties of metastable perovskite polymorphs of CsPbI3 in thin films10.1021/acs.chemmater.7b02948 ↗
43. Annealing effects on CsPbI3-based planar heterojunction perovskite solar cells formed by vacuum deposition method10.7567/JJAP.56.04CS11 ↗
44. Halide perovskite photovoltaics: background, status, and future prospects10.1021/acs.chemrev.8b00539 ↗
45. Energetics, structures, and phase transitions of cubic and orthorhombic cesium lead iodide (CsPbI3) polymorphs10.1021/jacs.9b05924 ↗
46. Band gap tuning via lattice contraction and octahedral tilting in perovskite materials for photovoltaics10.1021/jacs.7b04981 ↗
47. Resolving the physical origin of octahedral tilting in halide perovskites10.1021/acs.chemmater.6b00968 ↗
48. Beach-chair-shaped energy band alignment for high-performance β-CsPbI3 solar cells
49. Characterization of sequential physical vapor deposited methylammonium lead tri-iodide perovskite thin films10.1016/j.vacuum.2020.109727 ↗
50. Sequential physical vapor deposited methylammonium lead tri-iodide perovskites on FTO and ITO modified zinc oxide nanorods for perovskite solar cells10.1016/j.physb.2021.413462 ↗