journal article·2025-03

Enhancing Ni/Cr/n-GaN schottky junction performance using a novel Bi2O3 insulating layer for advanced optoelectronic device applications

V. Manjunath, M. Vani, N.V. Srihari, Penchalaneni Josthna, P. Rosaiah, N. Nanda Kumar Reddy, K. Munirathnam, Salh Alhammadi, Siva Kumar Koppala, Srinivas Reddy Golkonda, G. Vinod, J. Laxman Naik, Vasudeva Reddy Minnam Reddy, Woo Kyoung Kim, Mohammad Rezaul Karim

Publisher page

Abstract

Bismuth oxide (Bi 2O 3) insulator layer was used to prepare a Ni/Cr/Bi 2O 3/n-GaN Metal-insulator-semiconductor (MIS)-type junction. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), current–voltage (I-V), and capacitance–voltage (C-V) techniques were used to examine the junctions structural, chemical, and electrical properties. XRD, and SEM findings indicated that the Bi 2O 3 films exhibited a high-quality interface between metals and n-GaN substrate. The XPS depth profile shows a list of elements within the prepared MIS junction. Ni, Cr, Ga, O, N, Ti, Bi, and Al are among the elements in this junction. The significant concentration of these elements stands out notably in both the interfacial layer and the metal electrodes on n-GaN substrate. Remarkably, the prepared MIS junction exhibited superior rectifying behavior coupled with reduced reverse leakage current when compared with the Ni/Cr/n-GaN Metal-Semiconductor (MS) junction. The calculations demonstrated that the MIS junction exhibits a higher barrier height (1.18 eV) and ideality factor (1.32) compared to the MS junction, which has a barrier height of 0.84 eV and an ideality factor of 1.15. These results indicate that the Bi 2O 3 insulating layer significantly modifies the electrical properties of the prepared junction. Utilizing various methodologies, including Cheung’s, Norde functions, Ψ S-V, and Hernandez plots, barrier heights, ideality factor and series resistance were estimated and found to be consistent with each other. The Bi 2O 3 interlayer has demonstrated its effectiveness as a high-quality insulating material, making it an excellent candidate for the fabrication of GaN-based MIS junctions. Its presence enhances the device’s electrical properties, providing superior insulation and optimizing interface performance for advanced optoelectronic applications.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: GaN-based semiconductor devices and materials · Semiconductor materials and devices · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (76)

Show source-provided references
1. Metal-insulator-semiconductor capacitors with bismuth oxide as insulator10.1063/1.329294 ↗
2. Bismuth-based photocatalytic semiconductors: Introduction, challenges and possible approaches10.1016/j.molcata.2016.07.030 ↗
3. Metal-semimetal Schottky diode relying on quantum confinement10.1016/j.mee.2018.03.022 ↗
4. Effect of biologically synthesized iron-oxide nanoparticles insulating layer on current-voltage characteristics of Ni/Cr/Ni/n-GaN Schottky junction10.1016/j.mseb.2023.116908 ↗
5. Fabrication and Characterization of the Heterojunction Diode from Ternary Ni1-xCoxO Thin Films on n-Si Substrates by Sol-Gel Method, Brazilian
6. Enhancing of Al/Sn-HfO2/n-Si (MIS)Schottky barrier diode performance through the incorporation of Sn ions on high dielectric HfO2 thin films formedby spray pyrolysis10.1007/s10904-021-01997-0 ↗
7. K. Zhang, M.Y. Cao, Y.H. Chen, L.Y. Yang, C. Wang, X.H. Ma, Y. Hao, Fabrication and characterization of V-gate AlGaN/GaN high-electron-mobility transistors, Chinese Phys. B 22 (2013), 057304. doi:10.1088/1674-1056/22/5/057304.10.1088/1674-1056/22/5/057304 ↗
8. DC and RF characteristics of AlGaN/GaN HEMT and MOS-HEMT
9. Extraction of AlGaN/GaN heterostructure Schottky diode barrier heights from forward current-voltage characteristics
10. Digital integrated circuits on an E-Mode GaN power HEMT platform10.1109/LED.2017.2725908 ↗
11. Electrical properties of Au/Bi0.5Na0.5TiO3-BaTiO3/n-GaN metal-insulator-semiconductor (MIS) structure10.1088/0268-1242/29/7/075001 ↗
12. Effect of a graphene interlayer on the electrical properties of an AlGaN/GaN schottky diode10.1166/jnn.2016.13141 ↗
13. Materials Science in Semiconductor Processing Effect of copper phthalocyanine (CuPc) interlayer on the electrical characteristics of Au / n-GaN Schottky rectifier10.1016/j.mssp.2014.10.047 ↗
14. Janardhanam · Superlattices and Microstructures Schottky Contacts to n-Type GaN · 2018 · 120 · 50810.1016/j.spmi.2018.06.019 ↗
15. Structural, Chemical and Electrical Properties of Au/La2O3/n-GaN MIS Junction with a High-k Lanthanum Oxide Insulating Layer10.1007/s11664-019-07193-8 ↗
16. TCAD simulation capabilities towards gate leakage current analysis of advanced AlGaN/GaN HEMT devices10.1016/j.microrel.2017.07.049 ↗
17. Analysis of the temperature-dependent current-voltage characteristics and the barrier-height inhomogeneities of Au/GaN Schottky diodes10.1002/pssa.201228237 ↗
18. Platinum/porous GaN nanonetwork metal-semiconductor Schottky diode for room temperature hydrogen sensor10.1016/j.sna.2014.01.014 ↗
19. Effects of Annealing on Electrical Characteristics and Current Transport Mechanisms of the Y/p-GaN Schottky Diode10.1007/s11664-016-4490-9 ↗
20. Exploration of microstructural, chemical states and electrical features of the Au/Er2O3/n-GaN MIS diode with a Er2O3 interlayer
21. Incorporation of Ba2+ ions on the properties of MoO3 thin films and fabrication of positive photo-response Cu/Ba–MoO3/p-Si structured diodes10.1016/j.spmi.2019.106197 ↗
22. A review on Bi2O3 nanomaterial for photocatalytic and antibacterial applications10.1016/j.chphi.2024.100517 ↗
23. Bi2O3 doped indium tin oxide thin films fabricated via liquid metal printing10.1016/j.jallcom.2023.173077 ↗
24. Synthesis of Bi2O3 nanocones over large areas by magnetron sputtering10.1016/j.surfcoat.2015.01.072 ↗
25. Enhanced Performance of β-Bi2O3 by In-Situ Photo-Conversion to Bi2O3-BiO2-x Composite Photoanode for Solar Water Splitting10.1149/2.0721607jes ↗
26. The effect of PVA (Bi2O3-doped) interfacial layer and series resistance on electrical characteristics of Au/n-Si (110) Schottky barrier diodes (SBDs)10.1016/j.cap.2011.08.012 ↗
27. Z-scheme carbon-bridged Bi2O3/TiO2 nanotube arrays to boost photoelectrochemical detection performance10.1016/j.apcatb.2019.01.077 ↗
28. Investigation of the effect of different Bi2O3–x:PVA (x = Sm, Sn, Mo) thin insulator interface-layer materials on diode parameters10.1007/s10854-020-03343-5 ↗
29. Synthesis of Bi2O3/TiO2 nanostructured films for photocatalytic applications10.1016/j.ceramint.2018.09.040 ↗
30. Current research status of interface of ceramic-metal laminated composite material for armor protection
31. Interface-charge induced giant electrocaloric effect in lead free ferroelectric thin-film bilayers10.1021/acs.nanolett.9b04727 ↗
32. Interface-driven multiferroicity in Cubic BaTiO3-SrTiO3nanocomposites10.1021/acsnano.2c07215 ↗
33. V. Manjunath, Chaitanya Kumar Kunapalli, M. Vani, R. Jaya Madhuri, Sameh Abdallah Ragab, Mohammad Rezaul Karim, N. Nanda Kumar Reddy, K. Munirathnam, P.R. Sekhar Reddy, Himagirish Kumar Siddarapu, Tae J. Ko, Nunna Guru Prakash, P. Rosaiah, Effects of Zn doped MoO3 nanocomposite interlayer on electrical and surface chemical state properties of Ni/Cr/n-GaN Schottky junction, Materials Science and Engineering B 308 (2024)117602. doi: 10.1016/j.mseb.2024.117602.10.1016/j.mseb.2024.117602 ↗
34. (Al, Cu), Co‑doped ZnS nanoparticles: structural, chemical, optical, and photocatalytic properties
35. Statistical analysis of current–voltage characteristics in Au/Ta2O5/n-GaN Schottky barrier heterojunction using different methods10.1007/s00339-020-04173-2 ↗
36. Electrical and frequency-dependent properties of Au/Sm2O3/n-GaN MIS junction with a high-k rare-earth Sm2O3 as interlayer
37. Influence of single and double interlayers on the electrical and current transport mechanism of Mo/n-Si Schottky diode and its microstructural and chemical properties10.1007/s00339-023-06664-4 ↗
38. Analysis of the chemical states and microstructural, electrical, and carrier transport properties of the Ni/HfO2/Ga2O3/n-GaN MOS junction10.1007/s10854-023-10149-8 ↗
39. α-Bi2O3 photoanode in DSSC and study of the electrode-electrolyte interface10.1039/C5RA12760B ↗
40. Synthesis, characterization and photocatalytic activity of α-Bi2O3 nanoparticles10.1016/j.jtusci.2015.01.009 ↗
41. Controlled preparation of β-Bi2O3/Mg–Al mixed metal oxides composites with enhanced visible light photocatalytic performance10.1007/s11164-020-04237-1 ↗
42. An investigation on phase formations and microstructures of Ni-rich Ni-Ti shape memory alloy thin films10.1007/s11661-010-0497-7 ↗
43. Investigation on the effect of process parameter on physical properties of RF-sputtered Mo–Ni thin films as a back contact thin-film solar cell10.1007/s10854-021-07040-9 ↗
44. Structural and optical properties of ZnO and Ni:ZnO thin films: the trace of post-annealing10.1007/s10854-020-05092-x ↗
45. Chemical Visualization of a GaN p-n junction by XPS10.1038/srep14091 ↗
46. XPS Study in BiFeO3 Surface Modified by Argon Etching10.3390/ma15124285 ↗
47. Microstructural, electrical and carrier transport properties of Au/NiO/n-GaN heterojunction with a nickel oxide interlayer10.1039/C6RA23476C ↗
48. Reduction and removal of chromium VI in water by powdered activated carbon
49. β-Ta and α-Cr thin films deposited by high power impulse magnetron sputtering and direct current magnetron sputtering in hydrogen containing plasmas10.1016/j.physb.2013.11.038 ↗
50. Investigation of N Type Metal TiAlC by Thermal Atomic Layer Deposition Using TiCl4 and TEA as Precursors10.1149/2.0291605jss ↗
51. A. Obrosov, R. Gulyaev, M. Ratzke, A.A. Volinsky, S. Bolz, M. Naveed, S. Weiß, XPS and AFM investigations of Ti-Al-N coatings fabricated using DC magnetron sputtering at various nitrogen flow rates and deposition temperatures, Metals (basel). 7 (2017) 52, doi:10.3390/met7020052.10.3390/met7020052 ↗
52. Investigation of surface treatments for nonalloyed ohmic contact formation in Ti/Al contacts to n-type GaN10.1063/1.1332827 ↗
53. Investigation of Surface Segregation in Fe-Cr-Si Alloys by XPS10.1007/s11661-020-05758-5 ↗
54. Rhoderick · Metal-Semiconductor Contacts Second Edition · 1988 · 124
55. Electrical properties and current transport mechanisms of the Au/n-GaN Schottky structure with solution- processed high-k BaTiO3 interlayer10.1007/s11664-014-3177-3 ↗
56. Extraction of Schottky diode parameters from forward current-voltage characteristics10.1063/1.97359 ↗
57. A modified forward I-V plot for Schottky diodes with high series resistance10.1063/1.325607 ↗
58. A new technique for the determination of barrier height of Schottky barrier diodes10.1016/0038-1101(94)00167-E ↗
59. Barrier height determination in homogeneous nonideal Schottky contacts10.1088/0022-3727/34/8/305 ↗
60. Extraction of Schottky diode parameters from forward current-voltage characteristics10.1063/1.97359 ↗
61. Enhanced photocatalytic activity of novel α-Bi2O3@g-C3N4 composites for the degradation of endocrine-disrupting benzophenone-3 in water under visible light10.1186/s42834-022-00129-8 ↗
62. Fabrication of La-Doped Bi2O3 Nanoparticles with Oxygen Vacancies for Improving Photocatalytic Activity10.1007/s10562-019-02970-w ↗
63. Rapid thermal annealing influences on microstructure and electrical properties of Mo/ZrO2/n-Si/Al MISM junction with a high-k ZrO2 insulating layer10.1016/j.physb.2022.414423 ↗
64. Doping rate, Interface states and Polarization Effects on Dielectric Properties, Electric Modulus, and AC Conductivity in PCBM/NiO:ZnO/p-Si Structures in Wide Frequency Range10.1007/s12633-021-01640-0 ↗
65. Tuğluoğlu, Fabrication of a New Hybrid Coronene/n-Si Structure by Using Spin Coating Technique and its Photoresponse and Admittance Spectroscopy Studies10.1007/s12633-019-00233-2 ↗
66. Complex dielectric, complex electric modulus, and electrical conductivity in Al/(Graphene-PVA)/p-Si (metal-polymer-semiconductor) structures10.1016/j.jpcs.2020.109740 ↗
67. Investigation of the interface state characteristics of the Al/Al2O3/Ge/p-Si heterostructure over a wide frequency range by capacitance and conductance measurements10.1016/j.mssp.2023.107951 ↗
68. On the impact of pure PVC and (PVC: Ti) interlayer on the conduction mechanisms and physical parameters of classic metal-semiconductor (MS) Schottky diodes (SDs)
69. Potential barrier modification and interface states formation in metal-oxide-metal tunnel junctions10.1103/PhysRevB.80.125413 ↗
70. Studies of tunnel MOS diodes I. Interface effects in silicon Schottky diodes, J. Phys. D
71. A comparison of electrical characteristics of the Au/n-Si Schottky diodes with (ZnCdS:GO(1:1) and (ZnCdS:GO(1:0.5) doped PVP interlayer using current–voltage (I–V) and impedance–voltage (Z–V) measurements
72. Examination on the current conduction mechanisms of Au/n-Si diodes with ZnO–PVP and ZnO/Ag2WO4–PVP interfacial layers10.1007/s10971-023-06177-9 ↗
73. The interface states and series resistance effects on the forward and reverse bias I–V, C–V and G/ω-V characteristics of Al–TiW–Pd2Si/n-Si Schottky barrier diodes10.1016/j.jallcom.2010.04.210 ↗
74. Electrical properties of hybrid phthalocyanines thin films using gold and lead electrodes10.1140/epjb/e2005-00352-7 ↗
75. Electrical properties of Au/polyvinylidene fluoride/n-InP Schottky diode with polymer interlayer10.1016/j.tsf.2014.01.036 ↗
76. Effects of Rapid Thermal Annealing on the Structural, Optical, and Electrical Properties of Au/CuPc/n-Si (MPS)-type Schottky Barrier Diodes10.1007/s00339-021-04945-4 ↗