journal article·2024-12Open access

Study on the enhancement of device performance by the action of carbonohydrazide at the buried bottom interface of inverted mesoporous perovskite solar cells

Ju Lei, Feiping Lu, Yongjun Wei, Xinqi Ai, Weijun Ling

Abstract

The interface of perovskite solar cells (PSCs) significantly influences their efficiency and stability. Researchers tend to pay more attention to the upper surface of the perovskite absorber layer and conduct relatively less research on the bottom buried interface, mainly because the bottom of the perovskite film is challenging to peel off, which increases the difficulty of the characterization of the observation and analysis. Defects at the bottom interface make it more challenging to optimize the treatment than the upper surface. For inverted PSCs, the interface located in direct contact between the light absorption layer of perovskite and the hole transport layer is the buried interface. The buried interface is the direct interface for transporting charge carriers of PSCs and is also the center of non-radiative compound enrichment. The defect density is higher than the defect density of perovskite film crystal. Due to the DMSO initially left in the commonly used perovskite precursor solution during the film formation process, evaporation during the annealing and crystallization process creates vacancy holes at the bottom of the perovskite layer film. These holes and crystal boundaries tend to produce many non-radiative recombinations. These holes are also the sites of photodecomposition, leading to reduced efficiency and stability in PSCs, ultimately impacting the overall performance of PSCs. The work adds an Al 2 O 3 mesoporous layer on top of the hole transport layer (HTL), which reduces the direct contact area between PTAA and perovskite film. In the perovskite precursor solution, we incorporate a solid additive called Carbonohydrazide (CBH), this substance replaces some of the DMSO and fills in the voids at the bottom of the perovskite film that is left when the DMSO evaporates. This process helps to reduce non-radiative recombination and photodegradation caused by the voids at the bottom of the perovskite, leading to an improvement in the efficiency and stability of the cell. The optimization of the buried bottom interface has improved the cell’s average efficiency from 17.6 % to 19.7 %, an 11.9 % increase. The aperture area of the devices in this work is 0.048 cm 2 , and the photoelectric conversion efficiency of our device still reaches 80.64 % of the initial efficiency after 600 h of continuous heating in a glove box with a nitrogen atmosphere, maintaining a test temperature of 60 °C.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Perovskite Materials and Applications · Conducting polymers and applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Green economy and waste management: an inevitable plan for materials science10.1016/j.pnsc.2022.01.001 ↗
2. Energy revolution: From a fossil energy era to a new energy era10.1016/j.ngib.2016.02.001 ↗
3. Photothermal chemistry based on solar energy: from synergistic effects to practical applications
4. Highly efficient conversion of solar energy by the photoelectric converter and a thermoelectric converter10.4236/jamp.2018.63047 ↗
5. Photoelectrolysis of water: Solar hydrogen–achievements and perspectives10.1364/OE.18.00A147 ↗
6. Photovoltaic materials: Present efficiencies and future challenges10.1126/science.aad4424 ↗
7. Passivation of interfaces in thin film solar cells: Understanding the effects of a nanostructured rear point contact layer10.1002/admi.201701101 ↗
8. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells10.1021/ja809598r ↗
9. Highly efficient and stable perovskite solar cells via a multifunctional hole transporting material10.1016/j.joule.2024.02.019 ↗
10. Decomposition and cell failure mechanisms in lead halide perovskite solar cells10.1021/acs.inorgchem.6b01307 ↗
11. Stabilizing perovskite-substrate interfaces for high-performance perovskite modules10.1126/science.abi6323 ↗
12. Lead-chelating hole-transport layers for efficient and stable perovskite minimodules10.1126/science.ade9463 ↗
13. Mapping the space charge carrier dynamics in plasmon-based perovskite solar cells10.1039/C9TA02852H ↗
14. M.J. Brites, M.A. Barreiros, V. Corregidor, L.C. Alves, J. V. Pinto, M.J. Mendes, E. Fortunato, R. Martins, J.o. Mascarenhas, Ultrafast low-temperature crystallization of solar cell graded formamidinium-cesium mixed-cation lead mixed-halide perovskites using a reproducible microwave-based process, ACS Appl. Energy Mater. 2(3) (2019) 1844-1853. doi: 10.1021/acsaem.8b02005.10.1021/acsaem.8b02005 ↗
15. Constructing a stable and efficient buried heterojunction via halogen bonding for inverted perovskite solar cells10.1002/aenm.202203250 ↗
16. Orientated crystallization of FA-based perovskite via hydrogen-bonded polymer network for efficient and stable solar cells
17. Molecular bridge on buried interface for efficient and stable perovskite solar cells10.1002/anie.202304568 ↗
18. Engineering the buried interface in perovskite solar cells via lattice-matched electron transport layer10.1038/s41566-023-01247-4 ↗
19. Surface-tension release in PTAA-based inverted perovskite solar cells10.1016/j.orgel.2021.106378 ↗
20. Quantitative 1H NMR spectroscopy10.1016/j.trac.2012.02.007 ↗
21. Photoluminescence Enhancement in Formamidinium Lead Iodide Thin Films10.1002/adfm.201600715 ↗
22. Tailoring passivation molecular structures for extremely small open-circuit voltage loss in perovskite solar cells10.1021/jacs.8b13091 ↗
23. Dynamics of charged excitons and biexcitons in CsPbBr 3 perovskite nanocrystals revealed by femtosecond transient-absorption and single-dot luminescence spectroscopy10.1021/acs.jpclett.7b00326 ↗
24. D.d. Quilettes, S. Vorpahl, S. Stranks, H. Nagaoka, G. Eperon, M. Ziffer, H. Snaith, D. Ginger, Impact of microstructure on local carrier lifetime in perovskite solar cells, Science 348(6235) (2015) 683-686. doi: 10.1126/science.aaa5333.10.1126/science.aaa5333 ↗
25. Hysteresis index: a figure without merit for quantifying hysteresis in perovskite solar cells10.1021/acsenergylett.8b01627 ↗
26. Low density of conduction and valence band states contribute to the high open-circuit voltage in perovskite solar cells10.1021/acs.jpcc.6b10914 ↗
27. Study on the defect density of states in light soaking effect enhanced performance of perovskite solar cells10.1088/1361-6463/ab1626 ↗
28. Impedance spectroscopy of metal halide perovskite solar cells from the perspective of equivalent circuits10.1021/acs.chemrev.1c00214 ↗
29. Efficacious engineering on charge extraction for realizing highly efficient perovskite solar cells10.1039/C7EE02685D ↗
30. Hysteresis characteristics and device stability10.1007/978-3-319-35114-8_10 ↗
31. Characterization of hydrophilic—hydrophobic polymeric surfaces by contact angle measurements10.1016/0021-9797(81)90120-X ↗
32. The chemical iodination of silver10.1071/CH9860827 ↗
33. Crystallization in one-step solution deposition of perovskite films: Upward or downward?10.1126/sciadv.abb2412 ↗
34. Investigating relation of photovoltaic factors with properties of perovskite films based on various solvents10.1016/j.nanoen.2015.12.013 ↗
35. Carrier transport in CH3NH3PbI3 films with different thickness for perovskite solar cells10.1002/admi.201600327 ↗
36. An interface stabilized perovskite solar cell with high stabilized efficiency and low voltage loss10.1039/C9EE00751B ↗