Grain growth enhancing through preheating treatment of a sputtered stacked metallic precursor for Cu(In, Al)Se2 thin film solar cells application
Source abstract
Abstract
Abstract The influence of preheating treatment of a sputtered stacked metallic precursor on structural property of the CuInAl precursor and detailed structural, morphological and optical analyses as well as in the finally obtained Cu(In, Al)Se2 (CIAS) thin film solar cell device characterization are investigated systematically. These results indicate that this preheating process exhibits a strong beneficial impact on crystal growth and eventually produces a substantial improvement in photovoltaic properties. However, further increase of the preheating temperature, despite enhancing grain growth, clustering of grains loosely distribute on the surface of the CIAS thin film, forming a rather rough morphology. Thus, an accurate control of the preheating temperature during grain growth process may be necessary. Here, when optimizing the preheating temperature to 300 °C, the largest grain size and the best photovoltaic performance achieved. The findings provide an important insight into the understanding of fundamental research of current chalcopyrite solar cell application.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. CuIn1−xAlxSe2 thin film solar cells with depth gradient composition prepared by selenization of evaporated metallic precursors10.1016/j.solmat.2014.09.003 ↗
2. Potassium-induced surface modification of Cu(In, Ga)Se2 thin films for high-efficiency solar cells10.1038/nmat3789 ↗
3. Influence of copper concentration in solutions on the growth mechanism and performance of electrodeposited Cu(In, Al)Se2 solar cells10.1016/j.solmat.2014.05.007 ↗
4. Low temperature sulfurization of electrodeposited Cu(In, Al)Se2 thin films10.1016/j.apsusc.2014.08.018 ↗
5. Cation substitution induced structural transition, band gap engineering and grain growth of Cu2CdxZn1−xSnS4 thin films10.1016/j.jallcom.2016.11.121 ↗
6. Achieving high efficiency Cu2ZnSn(S, Se)4 solar cells by non-toxic aqueous ink: defect analysis and electrical modeling10.1016/j.nanoen.2016.04.059 ↗
7. CuIn1−xAlxSe2 thin films and solar cells10.1063/1.1476966 ↗
8. Selenization of co-sputtered CuInAl precursor films10.1016/j.solmat.2009.12.005 ↗
9. Formation of CuInAlSe2 film with double graded bandgap using Mo(Al) back contact10.1016/j.solmat.2010.04.046 ↗
10. On the impact of na dynamics at the Cu2ZnSn(S, Se)4/CdS interface during post low temperature treatment of absorbers10.1021/acsami.5b12243 ↗
11. Investigation of Cu2ZnSnS4 thin films with controllable Cu composition and its influence on photovoltaic properties for solar cells10.1016/j.jallcom.2016.10.024 ↗
12. High-efficiency solar cells based on Cu(In, Al)Se2 thin films10.1063/1.1499990 ↗
13. Effects of a pre-annealing treatment (PAT) on Cu2ZnSn(S, Se)4 thin films prepared by rapid thermal processing (RTP) selenization10.1016/j.solmat.2015.06.059 ↗
14. Correlation between soft annealing conditions and structural, microstructural, morphological, and optical properties of CuInS2 thin films prepared by sulfurization of stacked precursor10.1016/j.jcrysgro.2014.02.001 ↗
15. Impact of alloying duration of an electrodeposited Cu/Sn/Zn metallic stack on properties of Cu2ZnSnS4 absorbers for thin film solar cells10.1002/pip.2638 ↗
16. Microstructural and morphological properties of sputtered Cu(In, Al)Se2 thin films for solar cell applications10.1016/j.matlet.2015.05.021 ↗
17. Another route to fabricate single-phase chalcogenides by post-selenization of Cu-In-Ga precursors sputter deposited from a single ternary target10.1016/j.solmat.2009.02.014 ↗
18. Real-time investigations of selenization reactions in the system Cu-In-Al-Se10.1002/pssa.200669558 ↗
19. Hydrazine-free solution-deposited CuIn(S, Se)2 solar cells by spray deposition of metal chalcogenides10.1021/acsami.6b01541 ↗
20. Investigation of microstructural and optical properties of Cu(In, Al)Se2 thin films with various copper content10.1016/j.jallcom.2015.08.148 ↗
21. Ecofriendly and nonvacuum electrostatic spray-assisted vapor deposition of Cu(In, Ga)(S, Se)2 thin film solar cells10.1021/acsami.5b06666 ↗
22. Co-electrodeposited Cu2ZnSnS4 thin-film solar cells with over 7% efficiency fabricated via fine-tuning of the Zn content in absorber layers10.1039/C5TA09636G ↗
23. Growth of Cu2ZnSnSe4 film under controllable se vapor composition and impact of low Cu content on solar cell efficiency10.1021/acsami.6b00081 ↗
24. Solution processing of chalcogenide semiconductors via dimensional reduction10.1002/adma.200802027 ↗
25. Studies on Cu2ZnSnS4 (CZTS) absorber layer using different stacking orders in precursor thin films10.1016/j.solmat.2011.07.005 ↗
26. A Temporary barrier effect of the alloy layer during selenization: tailoring the thickness of MoSe2 for efficient Cu2ZnSnSe4 solar cells10.1002/aenm.201402178 ↗
27. 7.1% efficient co-electrodeposited Cu2ZnSnS4 thin film solar cells with sputtered CdS buffer layers10.1039/C5GC02057C ↗