journal article·2023-09Open access

Novel air-electrode materials for low-cost inert-supported solid oxide cells: investigation of materials compatibility during co-sintering

M. M. Juckel, F. Grimm, S. Zischke, Y. J. Sohn, O. Guillon, N. H. Menzler

Journal of Materials Science· Volume 58· Issue 34

Abstract

Abstract For the investigation of the reactivity of alternative solid oxide cell air electrode materials with forsterite (Mg2SiO4), a magnesium silicate doped with Zn and Ca, five different phase materials were chosen: two Ruddlesden–Popper phase materials: La4Ni3O10 (L4N3) and La3Ni2O7 (L3N2) and three titanium-based perovskite materials: SrTiO3 (STO), SrTi0.75Fe0.25O3 (STF25) and CaTi0.9Fe0.1O3 (CTF). Forsterite was chosen as a support material for the fuel cell, as it is abundant and therefore relatively inexpensive. For the investigation of their reactivity, different types of samples were prepared: mixed pellets, double-layered pellets and screen-printed electrode inks on forsterite green substrates, which were subsequently co-sintered at T = 1300 °C. These samples and their cross sections were then studied using XRD, SEM, EDS and TEM lamella point analysis. Consequently, the impedance spectra were acquired to determine their electro-catalytic performance. The two Ruddlesden–Popper phase materials L4N3 and L3N2 are of high interest due to their thermodynamic stability and high electro-catalytic activity, resulting in a very low polarization resistance. However, this polarization resistance is increased when mixing with forsterite material. In case of the three titanium-based perovskites, the electro-catalytic activity is of less interest due to high polarization resistances.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Catalytic Processes in Materials Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Ruddlesden SN, Popper P (1958) The compound Sr3Ti2O7 and its structure. Acta Crystallogr 11:54–5510.1107/S0365110X58000128 ↗
2. Ruddlesden SN, Popper P (1957) New compounds of the K2NiF4 type. Acta Crystallogr 10:538–53910.1107/S0365110X57001929 ↗
3. Yatoo MA, Skinner SJ (2022) Ruddlesden–Popper phase materials for solid oxide fuel cell cathodes: a short review. Mater Today Proc 56:3747–375410.1016/j.matpr.2021.12.537 ↗
4. Birol T, Benedek NA, Fennie CJ (2011) Interface control of emergent ferroic order in Ruddlesden–Popper Sr{n+1}Ti{n}O{3n+1}. Phys Rev Lett 107:257602–25760610.1103/PhysRevLett.107.257602 ↗
5. Oh YS, Luo X, Huang FT, Wang Y, Cheong SW (2015) Experimental demonstration of hybrid improper ferroelectricity and the presence of abundant charged walls in (Ca, Sr)3Ti2O7 crystals. Nat Mater 14:407–41310.1038/nmat4168 ↗
6. Dwivedi A, Cormack AN (1991) Crystal chemistry of Ruddlesden–Popper type structures in high Tc ceramic superconductors. Bull Mater Sci 14:575–58410.1007/BF02744688 ↗
7. Woolley RJ, Skinner SJ (2014) Functionally graded composite La2NiO4+δ and La4Ni3O10−δ solid oxide fuel cell cathodes. Solid State Ion 255:1–510.1016/j.ssi.2013.11.041 ↗
8. Battle PD, Blundell SJ, Green MA, Hayes W, Honold M, Klehe AK, Laskey NS, Millburn JE, Murphy L, Rosseinsky MJ, Samarin NA, Singleton J, Sluchanko NE, Sullivan SP, Vente JF (1996) Colossal magnetoresistance in Sr2NdMn2O7; MnO6 (x=0.0, 0.1). J Phys Condens Matter 8:L427–L43410.1088/0953-8984/8/32/001 ↗
9. Nirala G, Yadav D, Upadhyay S (2020) Ruddlesden–Popper phase A2BO4 oxides: recent studies on structure, electrical, dielectric, and optical properties. J Adv Ceram 9:129–14810.1007/s40145-020-0365-x ↗
10. Choi S, Yoo S, Shin J-Y, Kim G (2011) High performance SOFC cathode prepared by infiltration of Lan+1NinO3n+1 (n = 1, 2, and 3) in porous YSZ. J Electrochem Soc 158:B995–B99910.1149/1.3598170 ↗
11. Amow G, Davidson IJ, Skinner SJ (2006) A comparative study of the Ruddlesden–Popper series, Lan+1NinO3n+1 (n = 1, 2 and 3), for solid-oxide fuel-cell cathode applications. Solid State Ion 177:1205–121010.1016/j.ssi.2006.05.005 ↗
12. Takahashi S, Nishimoto S, Matsuda M, Miyake M (2010) Electrode properties of the Ruddlesden–Popper series, Lan+1NinO3n+1 (n=1, 2, and 3), as intermediate-temperature solid oxide fuel cells. J Am Ceram Soc 93:2329–233310.1111/j.1551-2916.2010.03743.x ↗
13. Burriel M, Garcia MG, Rossell M, Figueras A, Van Tendeloo G, Santiso J (2007) Enhanced high-temperature electronic transport properties in nanostructured epitaxial thin films of the Lan+1NinO3n+1 Ruddlesden−Popper series (n = 1, 2, 3, ∞). J Chem Mater 19:4056–406210.1021/cm070804e ↗
14. Skinner SJ, Kilner JA (2000) Oxygen Diffusion and Surface Exchange in La2−xSrxNiO4+δ. Solid State Ion 135:709–71210.1016/S0167-2738(00)00388-X ↗
15. Wan J, Goodenough JB, Zhu JH (2007) Nd2−xLaxNiO4+δ, a mixed ionic/electronic conductor with interstitial oxygen, as a cathode material. Solid State Ion 178:281–28610.1016/j.ssi.2007.01.013 ↗
16. Kharton VV, Figueiredo FM, Navarro L, Naumovich EN, Kovalevsky AV, Yaremchenko AA, Viskup AP, Carneiro A, Marques FMB, Frade JR (2001) Ceria-based materials for solid oxide fuel cells. J Mater Sci 36:1105–1117. https://doi.org/10.1023/A:100481750614610.1023/A:1004817506146 ↗
17. Kilner JA, Shaw CKM (2002) Mass transport in La2Ni1−xCoxO4+δ Oxides with the K2NiF4 Structure. Solid State Ion 154:523–52710.1016/S0167-2738(02)00506-4 ↗
18. Boehm E, Bassat JM, Steil MC, Dordor P, Mauvy F, Grenier JC (2003) Oxygen transport properties of La2Ni1−xCuxO4+δ mixed conducting oxides. Solid State Sci 5:973–98110.1016/S1293-2558(03)00091-8 ↗
19. Aguadero A, Alonso JA, Escudero MJ, Daza L (2008) Evaluation of the La2Ni1−xCuxO4+δ system as SOFC cathode material with 8YSZ and LSGM as electrolytes. Solid State Ion 179:393–40010.1016/j.ssi.2008.01.099 ↗
20. Lou Z, Peng J, Dai N, Qiao J, Yan Y, Wang Z, Wang J, Sun K (2012) High performance La3Ni2O7 cathode prepared by a facile sol-gel method for intermediate temperature solid oxide fuel cells. Electrochem Commun 22:97–10010.1016/j.elecom.2012.06.004 ↗
21. Amow G, Skinner SJ (2006) Recent developments in Ruddlesden–Popper nickelate systems for solid oxide fuel cell cathodes. J Solid State Electrochem 10:538–54610.1007/s10008-006-0127-x ↗
22. Tsipis EV, Patrakeev MV, Waerenborgh JC, Pivak YV, Markov AA, Gaczynski P, Naumovich EN, Kharton VV (2007) Oxygen non-stoichiometry of Ln4Ni2.7Fe0.3O10−δ (Ln=La, Pr). J Solid State Chem 180:1902–191010.1016/j.jssc.2007.04.025 ↗
23. Brett DJL, Atkinson A, Brandon NP, Skinner SJ (2008) Intermediate temperature solid oxidefuelcells. Chem Soc Rev 37:1568–157810.1039/b612060c ↗
24. Menzler NH, Tietz F, Uhlenbruck S, Buchkremer HP, Stöver D (2010) Materials and manufacturing technologies for solid oxide fuel cells. J Mater Sci 45:3109–3135. https://doi.org/10.1007/s10853-010-4279-910.1007/s10853-010-4279-9 ↗
25. Menzler NH, Schafbauer W, Han F, Buchler O, Mucke R, Buchkremer HP, Stöver D (2010) Development of high power density solid oxide fuel cells (SOFCs) for long-term operation. In: Nie JF, Morton A (eds) PRICM 7, 1–3, pp 2875–287810.4028/www.scientific.net/MSF.654-656.2875 ↗
26. Roehrens D, Packbier U, Fang Q, Blum L, Sebold D, Bram M, Menzler N (2016) Operation of thin-film electrolyte metal-supported solid oxide fuel cells in lightweight and stationary stacks. Mater Microstruct Aspects Mater 9:762–768
27. Brandon NP, Corcoran D, Cummins D, Duckett A, El-Khoury K, Haigh D, Leah R, Lewis G, Maynard N, McColm T, Trezona R, Selcuk A, Schmidt M (2013) Development of metal supported solid oxide fuel cells for operation at 500–600 °C. J Mater Eng Perform 22:2900–290310.1007/s11665-013-0716-7 ↗
28. Brandner M, Bram M, Froitzheim J, Buchkremer HP, Stöver D (2008) Electrically conductive diffusion barrier layers for metal-supported SOFC. Solid State Ionics 179:1501–150410.1016/j.ssi.2008.03.002 ↗
29. Quadakkers WJ, Piron-Abellan J, Shemet V, Singheiser L (2003) Metallic interconnectors for solid oxide fuel cells—a review. Mater High Temp 20:115–127
30. Matte E, Holzlechner G, Epple L, Stolten D, Lupetin P (2019) Impact of silicate substrate and cosintering on cathode performance in an inert substrate-supported solid oxide fuel cell. J Power Sources 413:334–34310.1016/j.jpowsour.2018.12.025 ↗
31. Grimm F, Menzler NH, Guillon O (2020) Selection of cathode materials for forsterite supported solid oxide fuel cells—part i: materials interactions. J Power Sources 451:227607–22761710.1016/j.jpowsour.2019.227607 ↗
32. Grimm F, Neubert K, Karl J, Menzler NH, Guillon O (2020) Selection of cathode materials for forsterite-supported solid oxide fuel cells—part II: electro-catalytic activity. J Power Sources 451:227811–22782110.1016/j.jpowsour.2020.227811 ↗
33. Huízar-Félix AM, Hernández T, de la Parra S, Ibarra J, Kharisov B (2012) Sol-gel based pechini method synthesis and characterization of Sm1−xCaxFeO3 Perovskite 0.1 ≤ x ≤ 0.5. Powder Technol 229:290–29310.1016/j.powtec.2012.06.057 ↗
34. Danks AE, Hall SR, Schnepp Z (2016) The evolution of ‘sol–gel’ chemistry as a technique for materials synthesis. Mater Horiz 3:91–11210.1039/C5MH00260E ↗
35. Schulze-Küppers F, Donkelaar SFP, Baumann S, Prigorodov P, Sohn YJ, Bouwmeester HJM, Meulenberg WA, Guillon O (2015) Structural and functional properties of SrTi1−xFexO3−δ (0≤x≤1) for the use as oxygen transport membrane. Sep Pur Technol 147:414–42110.1016/j.seppur.2014.12.020 ↗
36. Liu P, Han N, Wang W, Ran R, Zhou W, Shao Z (2021) High-quality Ruddlesden–Popper Perovskite film formation for high-performance Perovskite. Solar Cells Adv Mater 33:2002582–200262210.1002/adma.202002582 ↗
37. Dang D, Li X, Lai SY, Gerdes K, Liu M (2014) Enhancing SOFC cathode performance by surface modification through infiltration. Energy Environ Sci 7:552–57510.1039/c3ee42926a ↗
38. van Doorn RHE, Bouwmeester HJM, Burggraaf AJ (1998) Kinetic decomposition of La0.3Sr0.7CoO3−δ perovskite membranes during oxygen permeation. Solid State Ion 111:263–27210.1016/S0167-2738(98)00191-X ↗
39. Lein HL, Wiik K, Grande T (2006) Kinetic demixing and decomposition of oxygen permeable membranes. Solid State Ion 177:1587–159010.1016/j.ssi.2006.03.001 ↗
40. Wærnhus I, Sakai N, Yokokawa H, Grande T, Einarsrud M-A, Wiik K (2004) Mass transport in La1−xSrxFeO3(x=0 and 0.1) measured by SIMS. Solid State Ion 175:69–7110.1016/j.ssi.2004.09.014 ↗
41. Wang B, Zydorczak B, Wu Z-T, Li K (2009) Stabilities of La0.6Sr0.4Co0.2Fe0.8O3−δ oxygen separation membranes—effects of kinetic demixing/decomposition and impurity segregation. J Membr Sci 344:101–10610.1016/j.memsci.2009.07.040 ↗
42. Gheitanchi R, Kharaziha M, Emadi R (2017) Sr-doped forsterite nanopowder: synthesis and biological properties. Ceram Int 43:12018–1202510.1016/j.ceramint.2017.06.054 ↗
43. Guo Y-Q, Yin Y-M, Tong Z, Yin J-W, Xiong M-W, Ma., Z.-F. (2011) Impact of synthesis technique on the structure and electrochemical characteristics of Pr0.6Sr0.4Co0.2Fe0.8O3 − δ (PSCF) cathode material. Solid State Ion 193:18–2210.1016/j.ssi.2011.03.002 ↗
44. Wilde V, Stormer H, Szasz J, Wankmüller F, Ivers-Tiffee E, Gerthsen D (2018) Gd0.2Ce0.8O2 diffusion barrier layer between (La0.58Sr0.4)(Co0.2Fe0.8)O3−δ cathode and Y0.16Zr0.84O2 electrolyte for solid oxide fuel cells: effect of barrier layer sintering temperature on microstructure. ACS Appl Energy Mater 1:6790–680010.1021/acsaem.8b00847 ↗
45. Szasz J, Wankmüller F, Wilde V, Störmer H, Gerthsen D, Menzler NH, Ivers-Tiffee E (2018) Nature and functionality of La0.58Sr0.4Co0.2Fe0.8O3-δ/Gd0.2Ce0.8O2-δ/Y0.16Zr0.84O2-δ interfaces in SOFCs. J Electrochem Soc 165:F898–F90610.1149/2.0031811jes ↗