journal article·2005-07

Characterization of FGM monomorph actuators fabricated using EPD

T. Li, Y. H. Chen, J. Ma

Journal of Materials Science· Volume 40· Issue 14
Publisher page

Abstract

Piezoelectric FGM monomorph actuators fabricated using electrophoretic deposition (EPD) were investigated. Both the physical and electromechanical properties were examined. The high voltage performance of the actuator in both static and dynamic state was focused. It was found that the monomorph exhibits tetragonal phase perovskite structure and the gradient variation of microstructure was observed over the cross section. The displacement keeps a wide range of linearity in the static state. In the dynamic state, the vibration displacement is both frequency and voltage dependent. The resonant frequency shifts to lower frequency range due to the higher vibration loss at higher voltages. This results in the frequency dependence of the vibration limitations. The vibration limitation is also voltage dependent. Above a cutoff voltage, the displacement may not increase. To obtain a higher resonant displacement or velocity, the frequency and voltage should match well. Temperature rise or heat generation is caused by vibration loss. The maximum temperature happens at the clamped end of the monomorph.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electrophoretic Deposition in Materials Science · Ferroelectric and Piezoelectric Materials · Dielectric materials and actuators

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. K. UCHINO, in “Piezoelectric Actuators and Ultrasonic Motors” (Kluwer Academic Publishers, Boston/Dordrecht/London, 1997) p. 130.
2. X. H. ZHU and Z. Y. MENG, Sensor. Actuat. A48 (1995) 169.10.1016/0924-4247(95)00996-5 ↗
3. Y. H. CHEN and J. MA, Mater. Sci. Forum. 437/438 (2003) 487.10.4028/www.scientific.net/MSF.437-438.487 ↗
4. Y. H. CHEN, T. LI and J. MA, J. Mater. Sci. 38 (2003) 2803.10.1023/A:1024468015242 ↗
5. Y. H. CHEN, J. MA and T. LI, Ceram. Int. 30 (2004) 1807.10.1016/j.ceramint.2003.12.114 ↗
6. Idem., ibid. 30 (2004) 683.10.1016/j.ceramint.2003.08.008 ↗
7. B. K. MUKHERJEE and S. SHERRIT, in “Fifth International Congress on Sound and Vibration” (Adelaide, South Australia, 1997) p. 395.
8. T. KANDA, Y. KOBAYASHI and T. HIGUCHI, Jpn. J. Appl. Phys. 42 (2003) 3014.10.1143/JJAP.42.3014 ↗
9. S. TAKAHASHI, Y. SASAKI and K. UCHINO, ibid. 34 (1995) 5328.10.1143/JJAP.34.5328 ↗
10. M. UMEDA, K. NAKAMURA and S. UEHA, ibid. 38 (1999) 5581.10.1143/JJAP.38.5581 ↗
11. S. TASHIRO, M. IKEHIRO and H. IGARASHI, ibid. 36 (1997) 3004.10.1143/JJAP.36.3004 ↗
12. J. H. HU, IEEE T. Ultrason. Ferr. 50 (2003) 594.10.1109/TUFFC.2003.1209546 ↗
13. M. D. HILL, G. S. WHITE and C. S. HWANG, J. Am. Ceram. Soc. 79 (1996) 1915.10.1111/j.1151-2916.1996.tb08013.x ↗
14. A. FURUTA and K. UCHINO, ibid. 76 (1993) 1615.10.1111/j.1151-2916.1993.tb03950.x ↗
15. Y. WANG, W. Y. CHU and L. J. QIAO, Mater. Lett. 57 (2003) 1156.10.1016/S0167-577X(02)00948-5 ↗