journal article·2021-09-08Open access

Proposal for a Novel Abrasive Machining Method for Preparing the Surface of Periarticular Tissue during Orthopedic Surgery on Hip Joints

Paweł Zawadzki

Abstract

Drilling, cutting, and milling are the most common methods used in orthopedic surgery. However, popular machining methods do not obtain the complex shape of the periarticular tissue surfaces, increasing operation time and patient recovery. This paper reports an attempt to research a novel design of a machining process for surgical procedures. A device using abrasion machining based on mechanical erosion was proposed. Machining uses an undefined geometry of the cutting grains to cut tissue in any direction during oscillatory tool movement. This new concept is based on a cylindrical abrasive device made of brown fused alumina and silicon carbide grains deposited with an epoxy resin binder on the surface of a polyamide shaft. The best results in terms of machining efficiency were obtained for grains of the BFA80 type. Cutting experiments with different values in terms of cutting speed, granulation of the abrasive grains, pressure forces, and machining scope showed that the proposed concept, by developing the shape of the device, allows for penetration of the tissue structure. The research shows the possibility of using the proposed method during periarticular tissue machining.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Orthopaedic implants and arthroplasty · Advanced machining processes and optimization · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Mechanical Engineering, Poznan University of Technology, Maria Sklodowska-Curie Square, 60-965 Poznan, Poland

References (64)

Show source-provided references
1. Dahotre, N.B., and Joshi, S.S. (2016). Machining of Bone and Hard Tissue, Springer.10.1007/978-3-319-39158-8 ↗
2. Modeling and experimentation of bone drilling forces10.1016/j.jbiomech.2011.12.012 ↗
3. Cortical bone drilling and thermal osteonecrosis10.1016/j.clinbiomech.2011.10.010 ↗
4. An analytical modeling wit experimetal validation of bone temperature rise in drilling process10.1016/j.medengphy.2020.07.007 ↗
5. Analysis of machining process and thermal conditions during vibration-assisted cortical bone drilling based on generated bone chip morphologies10.1016/j.medengphy.2020.07.016 ↗
6. An overview of thermal necrosis: Present and future10.1080/03007995.2019.1603671 ↗
7. Wang, Y., Zeng, D., Sun y Yu, B., Zhang, P., Hu, Y., and Zhang, J. (2015, January 6–9). State Detection of Bone Milling with Multi-sensor Information Fusion. Proceedings of the 2015 IEEE International Conference on Robotics and Biomimetics (ROBIO), Zhuhai, China.10.1109/ROBIO.2015.7419007 ↗
8. Mechanistic modeling of bone-drilling proces with experimental validation10.1016/j.jmatprotec.2013.11.001 ↗
9. Rounded cutting edge model for the prediction of bone sawing forces10.1115/1.4006972 ↗
10. Simulation and evaluation of a bone sawing procedure for orthognathic surgery based on an experimental force model10.1115/1.4026104 ↗
11. Effect of applied force and blade speed on histopathology of bone during resection by sagittal saw10.1016/j.medengphy.2013.12.002 ↗
12. Experimental investigation on cutting mechanisms in fixed diamond wire sawing of bone10.1016/j.precisioneng.2020.12.020 ↗
13. Thermal damage done to bone by burring and sawing with and without irrigation in knee arthroplasty
14. On modelling of cutting force and temperature in bone milling10.1016/j.jmatprotec.2018.11.039 ↗
15. A cortical bone milling force model based on orthogonal cutting distribution method10.1007/s40436-020-00300-7 ↗
16. Expermiantal analysis, statistical modeling and optimization of effective parameters on surface quality in cortical bone milling process10.1142/S0219519419500787 ↗
17. The study of bone cutting force with FEM10.4028/www.scientific.net/AMR.974.389 ↗
18. Surgical diamond tools for minimally invasive surgery in bone resection under smal quantity of coolant supply10.1016/j.precisioneng.2018.09.015 ↗
19. Mist cooling in neurosurgical bone grinding10.1016/j.cirp.2013.03.125 ↗
20. Treatment of Osteochondral Lesions of the Talus With Particulated Juvenile Cartilage10.1177/1071100713485739 ↗
21. The role of tissue engineering in articular cartilage repair and regeneration10.1615/CritRevBiomedEng.v37.i1-2.10 ↗
22. A Comparison Between Arthroscopic Repair and Open Reapir Procedures10.1177/0363546517698675 ↗
23. Current strategies for articular cartilage repair10.22203/eCM.v009a04 ↗
24. Osteochondral Allograft Transfer for Treatment of Osteochondral Lesions of the Talus: A Systematic Review10.1016/j.arthro.2016.06.011 ↗
25. Matrix-Assisted Autologous Chondrocyte Transplantation in the Knee. A Systematic Review of Mid- to Long-Term Clinical Outcomes10.1177/2325967117709250 ↗
26. Hip Resection Arthroplasty
27. Definitive Resection Arthroplasty of the Knee: A Surprisingly Viable Treatment to Manage Intractable Infection in Selected Patients10.1016/j.arth.2019.10.025 ↗
28. Five to Ten-Year Results of the Birmingham Hip Resurfacing Implant in the U.S.10.2106/JBJS.17.01525 ↗
29. From injectable to 3D printed hydrogels in maxillofacial tissue engineering: A review10.1016/j.jobcr.2020.09.006 ↗
30. First Biomimetic Fixation for Resurfacing Arthroplasty: Investigation in Swine of a Prototype Partial Knee Endoprosthesis10.1155/2019/6952649 ↗
31. Recent developments in grinding of advanced materials10.1007/s00170-008-1496-3 ↗
32. On the mechanics of the grinding process—Part I. Stochastic nature of the grinding proces10.1016/S0890-6955(03)00186-X ↗
33. An analysis of cutting force and surface finish in surface grinding of aisi H13 Steel
34. Cubic boron nitride tool topography effects on phase transformation of maraging C250 steel and grinding surface quality10.1007/s00170-020-05586-2 ↗
35. Profile grinding of DZ125 nickel-based superalloy: Grinding heat, temperature field, and surface quality10.1016/j.jmapro.2020.06.022 ↗
36. Development of actuators for ultrasonically assisted grinding of hard brittle material10.1007/s00170-019-04484-6 ↗
37. An experimental and theoretical analysis of surface generation in the ultra-precision grinding of hard and brittle materials10.1007/s00170-018-2121-8 ↗
38. Ultrasonic vibration assisted grinding of hard and brittle linear micro-structured surfaces10.1016/j.precisioneng.2016.11.009 ↗
39. Dimensional Accuracy Enhancement in CNC Batch Grinding through Fractional Order Iterative Learning Compensation10.1155/2014/260420 ↗
40. Development of novel high-shear and low-pressure grinding tool with flexible composite10.1080/10426914.2020.1843673 ↗
41. Shape adaptive grinding of CVD silicon carbide10.1016/j.cirp.2014.03.019 ↗
42. Theoretical and experimental investigation of material removal mechanism in compliant shape adaptive grinding process10.1016/j.ijmachtools.2019.04.011 ↗
43. Single grain scratch tests to determine elastic and plastic material behavior in grinding10.4028/www.scientific.net/AMR.325.48 ↗
44. Deformation mechanism and force modelling of the grinding of YAG single crystals10.1016/j.ijmachtools.2019.05.003 ↗
45. A New Model of Grinding Forces Prediction for Machining Brittle and Hard Materials
46. Modeling of Vibration Condition in Flat Surface Grinding Process
47. Modeling and simulation of the distribution of undeformed chip thicknesses in surface grinding10.1016/j.ijmachtools.2018.01.002 ↗
48. Influence of grain wear on material removal behavior during grinding nickel-based superalloy whit a single diamond grain10.1016/j.ijmachtools.2016.12.001 ↗
49. Mechanical wear of different crystallographic orientations for single abrasive diamond scratching on Ta12W10.1016/j.ijrmhm.2015.07.038 ↗
50. Ohnishi, O., Suzuki, H., Uhlmann, E., Schroer, N., Sammler, C., Weismiller, M., and Spur, G. (2015). Handbook of Ceramics Grinding and Polishing, William Andrew Publishing.10.1016/B978-1-4557-7858-4.00004-2 ↗
51. A Heat Transfer Model of Grinding Process Based on Energy Partition Analysis and Grinding Fluid Cooling Application10.1115/1.4037241 ↗
52. On a stochastically grain-discretized model for 2D/3D temperature mapping prediction in grinding10.1016/j.ijmachtools.2017.01.004 ↗
53. Surface and subsurface damage of reaction-bonded silicon carbide induced by electrical discharge diamond grinding10.1016/j.ijmachtools.2020.103564 ↗
54. Experimental investigation of material removal mechanism in single grit grinding10.1016/j.ijmachtools.2012.07.010 ↗
55. Syreyshchikova, N.V., Guzeev, V.I., Ardashev, D.V., Pimenov, D.Y., Patra, K., Kapłonek, W., and Nadolny, K.A. (2020). Study on the Machinability of Steels and Alloys to Develop Recommendations for Setting Tool Performance Characteristics and Belt Grinding Modes. Materials, 18.10.3390/ma13183978 ↗
56. Multiple criteria optimization in coated abrasive grinding of titanium alloy using minimum quantity lubrication10.1016/j.ijmachtools.2016.12.004 ↗
57. Determination of specific cutting force components and exponents when applying high feed rates10.1016/j.procir.2018.08.199 ↗
58. Influence of wood modification on cutting force, specific cutting resistance and fracture parameters during the sawing process using circular sawing machine10.1007/s00107-020-01581-2 ↗
59. Machinability of engineering polymers
60. Friction and wear of hemiarthroplasty biomaterials in reciprocating sliding contact with articular cartilage10.1115/1.4004760 ↗
61. A comparision of friction measurements of intact articular cartilage in contact with cartilage, glass and metal
62. Effect of dynamic loading on the frictional response of bovine articular cartilage10.1016/j.jbiomech.2004.07.025 ↗
63. On chip formation mechanism in orthogonal cutting of bone10.1016/j.ijmachtools.2015.12.004 ↗
64. Mechanism of material removal in orthogonal cutting of cortical bone10.1016/j.jmbbm.2020.103618 ↗