journal article·2026-03-13Open access

Design and Performance Evaluation of TPMS-Based Dual-Layer Gradient Porous Structures for Bone Scaffolds

Xiaobing Li, Donglai Zhou, Cuiyuan Lu, Min Zhong, Xianda Xie, Linyu Zhou, Yanghan Fu

Abstract

This study investigates and compares properties of various P-type Triply Periodic Minimal Surface (TPMS) porous structures for bone scaffold design. At first, six cases of homogeneous single/dual-layer structures, axial single/dual-layer gradient structures and radial single/dual-layer gradient structures with the same average porosity are developed. Dual-layer gradient structures are selected for further design due to more similar pore and stress distributions to human bones, reduced maximum stress, higher yield strength and greater variations in yield strength and elastic modulus (E). The mechanical and permeability properties of ten cases of axial and radial dual-layer gradient structures with the same overall porosity but different inner and outer layer porosities are then further designed and studied. The results show that yield strength is within 112.75–139.97 MPa, E ranges from 11.15 to 13.01 GPa, the permeability (K) falls within 1.51–10.01 × 10−9 m2 and the average wall shear stress (WSSavg) varies between 6.18 and 9.11 mPa. The yield strength, E and K of radial dual-layer gradient structures are higher and WSSavg is lower than those of axial dual-layer gradient structures. Moreover, with increase in inner average porosity (P¯) and decrease in outer P¯, the yield strength, E and K gradually decrease while WSSavg gradually increases for both types of structures. In particular, the radial dual-layer structure with the lowest porosity of 27.5% in the inner layer and highest porosity of 42.5% in the outer layer has superior mechanical and permeability properties. The findings offer direct guidance for the structural design of bone implants, enabling performance customization for different applications.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Cellular and Composite Structures · Bone Tissue Engineering Materials · Dental Implant Techniques and Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Advanced Manufacturing, Nanchang University, Nanchang 330031, China

Modern Mechanical Design Engineering Technology Research Center of Jiangxi Province Higher Education Institutions, Nanchang, 330031, China

School of Mechanical and Electronic Engineering, Gandong University, Fuzhou 344000, China

Jiangxi Province Key Laboratory of Light Alloy, Nanchang University, Nanchang 330031, China

Funding

National Natural Science Foundation of China · Natural Science Foundation of Jiangxi Province · 2023 Ganpo Talents Support Program—High level and Urgently Needed Oversea Talents Program

References (62)

Show source-provided references
1. Vascularized periosteal flaps accelerate osteointegration and revascularization of allografts in rats10.1097/CORR.0000000000000400 ↗
2. Chen, H., Han, Q., Wang, C., Liu, Y., Chen, B., and Wang, J. (2020). Porous scaffold design for additive manufacturing in orthopedics: A review. Front. Bioeng. Biotechnol., 8.10.3389/fbioe.2020.00609 ↗
3. 3D printed TPMS structural PLA/GO scaffold: Process parameter optimization, porous structure, mechanical and biological properties10.1016/j.jmbbm.2023.105848 ↗
4. Porous scaffolds for bone regeneration10.1016/j.jsamd.2020.01.007 ↗
5. Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials10.1016/j.actbio.2018.12.013 ↗
6. Customized 3D-printed heterogeneous porous titanium scaffolds for bone tissue engineering
7. Design and preparation of biomimetic” hard-soft” functional scaffold with gradient irregular pore structure for bone repair10.1016/j.jmrt.2024.11.013 ↗
8. Chao, L., He, Y., Gu, J., Xie, D., Yang, Y., Shen, L., Wu, G., Wang, L., and Tian, Z. (2023). Evaluation of compressive and permeability behaviors of trabecular-like porous structure with mixed porosity based on mechanical topology. J. Funct. Biomater., 14.10.3390/jfb14010028 ↗
9. He, S., Zhu, J., Jing, Y., Long, S., Tang, L., Cheng, L., and Shi, Z. (2024). Effect of 3D-printed porous titanium alloy pore structure on bone regeneration: A review. Coatings, 14.10.3390/coatings14030253 ↗
10. Wang, C., Wu, J., Liu, L., Xu, D., Liu, Y., Li, S., Hou, W., Wang, J., Chen, X., and Sheng, L. (2023). Improving osteoinduction and osteogenesis of Ti6Al4V alloy porous scaffold by regulating the pore structure. Front. Chem., 11.10.3389/fchem.2023.1190630 ↗
11. Ti–6Al–4V triply periodic minimal surface structures for bone implants fabricated via selective laser melting10.1016/j.jmbbm.2015.06.024 ↗
12. Ultrahigh-strength titanium gyroid scaffolds manufactured by selective laser melting (SLM) for bone implant applications10.1016/j.actamat.2018.08.005 ↗
13. Biocompatibility of Ti-alloys for long-term implantation10.1016/j.jmbbm.2012.11.014 ↗
14. Topology optimization for reducing stress shielding in cancellous bone scaffold10.1016/j.compstruc.2023.107132 ↗
15. Additively manufactured controlled porous orthopedic joint replacement designs to reduce bone stress shielding: A systematic review10.1186/s13018-022-03492-9 ↗
16. Advances in 3D-printed scaffold technologies for bone defect repair: Materials, biomechanics, and clinical prospects10.1186/s12938-025-01381-w ↗
17. Prediction of permeability of regular scaffolds for skeletal tissue engineering: A combined computational and experimental study10.1016/j.actbio.2011.12.021 ↗
18. On the determination of Darcy permeability coefficients for a microporous tissue scaffold10.1089/ten.tec.2009.0116 ↗
19. Permeability and fluid flow-induced wall shear stress in bone scaffolds with TPMS and lattice architectures: A CFD analysis10.1016/j.euromechflu.2019.09.015 ↗
20. Jiang, J., Huo, Y., Peng, X., Wu, C., Zhu, H., and Lyu, Y. (2024). Design of novel triply periodic minimal surface (TPMS) bone scaffold with multi-functional pores: Lower stress shielding and higher mass transport capacity. Front. Bioeng. Biotechnol., 12.10.3389/fbioe.2024.1401899 ↗
21. Samuel, S.P. (2004). Fluid/Solid Interactions in Cancellous Bone, Cleveland State University.
22. Measurements of permeability in human calcaneal trabecular bone10.1016/S0021-9290(97)00016-X ↗
23. Dependence of intertrabecular permeability on flow direction and anatomic site10.1114/1.195 ↗
24. Direct perfusion measurements of cancellous bone anisotropic permeability10.1016/S0021-9290(01)00082-3 ↗
25. Experimental and theoretical investigation of directional permeability of human vertebral cancellous bone for cement infiltration10.1016/S0021-9290(03)00246-X ↗
26. Hydraulic resistance and permeability in human lumbar vertebral bodies10.1115/1.1503793 ↗
27. Permeability studies of artificial and natural cancellous bone structures10.1016/j.medengphy.2012.08.011 ↗
28. Additively manufactured metallic porous biomaterials based on minimal surfaces: A unique combination of topological, mechanical, and mass transport properties10.1016/j.actbio.2017.02.024 ↗
29. Topological design, mechanical responses and mass transport characteristics of high strength-high permeability TPMS-based scaffolds10.1016/j.ijmecsci.2021.107023 ↗
30. Verma, R., Kumar, J., Singh, N.K., Rai, S.K., Saxena, K.K., and Xu, J. (2022). Design and analysis of biomedical scaffolds using TPMS-based porous structures inspired from additive manufacturing. Coatings, 12.10.3390/coatings12060839 ↗
31. Compression, permeability and grinding properties of selective laser melted porous metal-bonded diamond grinding tools10.1016/j.jmapro.2025.01.065 ↗
32. Ravichander, B.B., Jagdale, S.H., Theeda, S., and Kumar, G. (2022). Evaluation of Functionally Graded Lattice Properties of Laser Powder Bed Fused Stainless Steel 316L, University of Texas at Dallas.
33. Ahmed, N., Barsoum, I., and Abu Al-Rub, R.K. (2022). Numerical investigation on the effect of residual stresses on the effective mechanical properties of 3D-printed TPMS lattices. Metals, 12.10.3390/met12081344 ↗
34. Recent advances in bone tissue engineering scaffolds10.1016/j.tibtech.2012.07.005 ↗
35. Yin, F., Ye, X., Yao, H., Wei, P., Wang, X., Cong, J., and Tong, Y. (2021). Surface forming criteria of Ti-6AL-4V titanium alloy under laser loading. Appl. Sci., 11.10.3390/app11125406 ↗
36. Investigation on the orientation dependence of elastic response in Gyroid cellular structures10.1016/j.jmbbm.2018.09.042 ↗
37. Graded porous scaffold mediates internal fluidic environment for 3D in vitro mechanobiology10.1016/j.compbiomed.2025.109674 ↗
38. Flow rates in perfusion bioreactors to maximise mineralisation in bone tissue engineering in vitro10.1016/j.jbiomech.2018.08.004 ↗
39. Bending dominated response of layered mechanical metamaterials alternating pentamode lattices and confinement plates10.1016/j.compstruct.2016.07.031 ↗
40. Ashby, M.F., and Gibson, L.J. (1997). Cellular Solids: Structure and Properties, Press Syndicate of the University of Cambridge.
41. Toosi, S., Javid-Naderi, M.J., Tamayol, A., Ebrahimzadeh, M.H., Yaghoubian, S., and Mousavi Shaegh, S.A. (2024). Additively manufactured porous scaffolds by design for treatment of bone defects. Front. Bioeng. Biotechnol., 11.10.3389/fbioe.2023.1252636 ↗
42. Chen, S., Liao, K., Yang, Y., Chen, H., and Huang, R. (2025). Influence of Porosity Gradient Distribution on Mechanical and Biological Properties of Gyroid-Based Zn-2Mg Scaffolds for Bone Tissue Engineering. Materials, 18.10.3390/ma18184399 ↗
43. Stress concentration reduction in an axially loaded rectangular bar with an elliptical hole10.20983/culcyt.2023.1.2.2 ↗
44. Improving mechanical properties of lattice structures using nonuniform hollow struts10.1016/j.ijmecsci.2024.109674 ↗
45. Omar, A.M., Hassan, M.H., Daskalakis, E., Ates, G., Bright, C.J., Xu, Z., Powell, E.J., Mirihanage, W., and Bartolo, P.J.D.S. (2022). Geometry-based computational fluid dynamic model for predicting the biological behavior of bone tissue engineering scaffolds. J. Funct. Biomater., 13.10.3390/jfb13030104 ↗
46. Egger, D., Fischer, M., Clementi, A., Ribitsch, V., Hansmann, J., and Kasper, C. (2017). Development and characterization of a parallelizable perfusion bioreactor for 3D cell culture. Bioengineering, 4.10.3390/bioengineering4020051 ↗
47. Quantification of fluid shear stress in bone tissue engineering scaffolds with spherical and cubical pore architectures10.1007/s10237-015-0710-0 ↗
48. Finite element analysis of mechanical behavior, permeability and fluid induced wall shear stress of high porosity scaffolds with gyroid and lattice-based architectures10.1016/j.jmbbm.2017.07.035 ↗
49. Additive manufacturing of functionally graded porous titanium scaffolds for dental applications10.1016/j.bioadv.2022.213018 ↗
50. Mechanical and fatigue performance of multidirectional functionally graded Ti6Al4V scaffolds produced via laser powder bed fusion for orthopedic implants10.1016/j.matdes.2025.113725 ↗
51. Gyroid-based functionally graded porous titanium scaffolds for dental application: Design, simulation and characterizations10.1016/j.matdes.2022.111300 ↗
52. 3D-printed Ti6Al4V scaffolds with graded triply periodic minimal surface structure for bone tissue engineering10.1007/s11665-021-05580-z ↗
53. Functionally graded porous scaffolds in multiple patterns: New design method, physical and mechanical properties10.1016/j.matdes.2018.09.053 ↗
54. Mechanical properties and fluid permeability of gyroid and diamond lattice structures for intervertebral devices: Functional requirements and comparative analysis10.1080/14686996.2021.1907222 ↗
55. The design of Ti6Al4V Primitive surface structure with symmetrical gradient of pore size in biomimetic bone scaffold10.1016/j.matdes.2020.108830 ↗
56. Xiao, F., Ren, G.H., Pan, C.Y., Xu, X., Cheng, K.J., You, J., and Liu, Y.F. (2025). Design and in vitro evaluation of gradient Schwarz Primitive scaffolds with thin-board integration for bone implants. Biomater. Adv., 214412.10.1016/j.bioadv.2025.214412 ↗
57. Additive manufacturing of multi-morphology graded titanium scaffolds for bone implant applications10.1016/j.jmst.2022.07.035 ↗
58. Parametric design and performance study of continuous gradient triply periodic minimal surface bone scaffold10.36922/ijb.2306 ↗
59. On the permeability of TPMS scaffolds10.1016/j.jmbbm.2020.103932 ↗
60. Shen, H., Song, C., Yang, L., and Gan, Y. (2026, January 24). Influence of Cell Size and Porosity on Permeability in Bone Scaffold TPMS Structures. Available online: https://www.researchsquare.com/article/rs-5174277/v1.
61. Baumer, V., Isaacson, N., Kanakamedala, S., McGee, D., Kaze, I., and Prawel, D. (2024). Comparing ceramic Fischer-Koch-S and gyroid TPMS scaffolds for potential in bone tissue engineering. Front. Bioeng. Biotechnol., 12.10.3389/fbioe.2024.1410837 ↗
62. Lv, Y., Liu, G., Wang, B., Tang, Y., Lin, Z., Liu, J., Wei, G., and Wang, L. (2022). Pore strategy design of a novel NiTi-Nb biomedical porous scaffold based on a triply periodic minimal surface. Front. Bioeng. Biotechnol., 10.10.3389/fbioe.2022.910475 ↗