journal article·2025-03-28Open access

Fabrication and Characterization of Highly Porous Gyroid Scaffolds Composed of Deproteinized Bone Mineral

Otoniel Durán Hernández, Vail Baumer, Genesis Marrero, Sreya Karumanchi, David Prawel

Abstract

Current treatment methods for critical bone defects involve the implantation of large bone grafts, which are limited by tissue availability and failure to heal correctly with high complication rates. Bioengineered scaffolds have emerged, which deploy biodegradable, highly osteoconductive materials in porous structures to accommodate the high mass transport requirements of large bone defects. Ideal scaffold biomaterials require a balance between strength, composition, and osteoconduction, a balance which has yet to be discovered. Naturally derived materials like deproteinized bovine bone mineral (DBBM) have seen successful clinical use for decades as bone void fillers, but their granular or putty form lacks the interconnected porosity required to treat large defects. Leveraging the clinical success of DBBM, this paper presents the first fabrication of highly porous scaffolds composed of naturally derived, deproteinized bone mineral, for potential use in large bone defects. Ovine bone mineral powder was prepared from fresh ovine bone, fabricated into a photopolymeric slurry and 3D-printed using a photocasting process into 67% porous gyroid scaffolds. Ovine bone mineral composition, surface microstructure, compressive properties, and failure probability were evaluated and compared to gyroid scaffolds composed of tricalcium phosphate. Both scaffold types were similar, with characteristics in the low range of human cancellous bone.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Bone Tissue Engineering Materials · Dental Implant Techniques and Outcomes · Periodontal Regeneration and Treatments

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Materials Science and Engineering, Colorado State University, Fort Collins, CO 80523, USA

Department of Mechanical Engineering, Colorado State University, Fort Collins, CO 80523, USA

School of Biomedical Engineering, Colorado State University, Fort Collins, CO 80523, USA

Funding

National Institute of Arthritis and Musculoskeletal and Skin Diseases (NIAMS) · Office of Economic Development & International Trade (OEDIT) · Colorado State University Translational Medicine Institute Translational Acceleration Program (TMI TAP)

References (74)

Show source-provided references
1. Ekegren, C.L., Edwards, E.R., De Steiger, R., and Gabbe, B.J. (2018). Incidence, Costs and Predictors of Non-Union, Delayed Union and Mal-Union Following Long Bone Fracture. Int. J. Environ. Res. Public Health, 15.10.3390/ijerph15122845 ↗
2. The global burden of fractures10.1016/S2666-7568(21)00183-5 ↗
3. Polaris Market Research (2024). Bone Grafts and Substitutes Market Share, Size, Trends, Industry Analysis Report, Polaris Market Research. Available online: https://www.polarismarketresearch.com/industry-analysis/bone-grafts-substitutes-market.
4. Prevalence of complications of open tibial shaft fractures stratified as per the Gustilo–Anderson classification10.1016/j.injury.2011.10.015 ↗
5. Vidal, L., Kampleitner, C., Brennan, M.Á., Hoornaert, A., and Layrolle, P. (2020). Reconstruction of Large Skeletal Defects: Current Clinical Therapeutic Strategies and Future Directions Using 3D Printing. Front. Bioeng. Biotechnol., 8.10.3389/fbioe.2020.00061 ↗
6. A technique for creating critical-size defects in the metatarsus of sheep for use in investigation of healing of long-bone defects10.2460/ajvr.2004.65.1653 ↗
7. History of lower limb reconstruction after trauma: History of lower limb reconstruction after trauma10.1111/j.1445-2197.2012.06271.x ↗
8. Additive manufacturing of biomaterials10.1016/j.pmatsci.2017.08.003 ↗
9. 3D-printed biodegradable gyroid scaffolds for tissue engineering applications10.1016/j.matdes.2018.04.037 ↗
10. Mechanical properties of 3D printed polymeric Gyroid cellular structures: Experimental and finite element study10.1016/j.matdes.2019.107597 ↗
11. Additive manufacturing technology for porous metal implant applications and triple minimal surface structures: A review
12. In vitro assessment of laser sintered bioactive glass scaffolds with different pore geometries10.1108/RPJ-12-2014-0175 ↗
13. High strength porous PLA gyroid scaffolds manufactured via fused deposition modeling for tissue-engineering applications
14. Minimal surface scaffold designs for tissue engineering10.1016/j.biomaterials.2011.06.012 ↗
15. Insights into the mechanical properties of several triply periodic minimal surface lattice structures made by polymer additive manufacturing10.1016/j.polymer.2017.11.049 ↗
16. Santos, J., Pires, T., Gouveia, B.P., Castro, A.P.G., and Fernandes, P.R. (2020). On the permeability of TPMS scaffolds. J. Mech. Behav. Biomed. Mater., 110.10.1016/j.jmbbm.2020.103932 ↗
17. Finite element study of scaffold architecture design and culture conditions for tissue engineering10.1016/j.biomaterials.2009.07.041 ↗
18. Ambrosio, K.V.L. (2019). Hydroxyapatite Structures Created by Additive Manufacturing with Extruded Photopolymer. [Master’s Thesis, Colorado State University].
19. Compressive properties and failure behavior of photocast hydroxyapatite gyroid scaffolds vary with porosity10.1177/08853282211073904 ↗
20. Porous scaffold design for tissue engineering10.1038/nmat1421 ↗
21. 3D printing of ceramic implants10.1557/mrs.2015.326 ↗
22. Calcium Phosphate-Based Resorbable Ceramics: Influence of MgO, ZnO, and SiO2 Dopants: Calcium Phosphate-Based Resorbable Ceramics10.1111/j.1551-2916.2006.01207.x ↗
23. Understanding in vivo response and mechanical property variation in MgO, SrO and SiO2 doped β-TCP10.1016/j.bone.2011.03.685 ↗
24. Microwave-sintered 3D printed tricalcium phosphate scaffolds for bone tissue engineering10.1002/term.555 ↗
25. Effects of MgO, ZnO, SrO, and SiO2 in tricalcium phosphate scaffolds on in vitro gene expression and in vivo osteogenesis10.1016/j.msec.2018.10.073 ↗
26. Understanding of dopant-induced osteogenesis and angiogenesis in calcium phosphate ceramics10.1016/j.tibtech.2013.06.005 ↗
27. Understanding the influence of MgO and SrO binary doping on the mechanical and biological properties of β-TCP ceramics10.1016/j.actbio.2010.05.012 ↗
28. Silicon substitution in the calcium phosphate bioceramics10.1016/j.biomaterials.2007.05.003 ↗
29. Synthesis of functionally graded MgCO3 apatite accelerating osteoblast adhesion10.1002/jbm.10220 ↗
30. Study of the reactivity and in vitro bioactivity of Sr-substituted α-TCP cements10.1007/s10856-005-4754-z ↗
31. Influence of ZnO doping in calcium phosphate ceramics10.1016/j.msec.2005.11.004 ↗
32. Up-regulation by zinc of FGF-2-induced VEGF release throughenhancing p44/p42 MAP kinase activation in osteoblasts10.1016/j.lfs.2006.09.003 ↗
33. Silica-based bioactive glasses modulate expression of bone morphogenetic protein-2 mRNA in Saos-2 osteoblasts in vitro10.1016/S0142-9612(00)00288-X ↗
34. Effect of silicon-containing hydroxyapatite coatings on the human in vitro osteoblastic response10.1016/j.bone.2009.03.464 ↗
35. Extracellular matrix formation and mineralization on a phosphate-free porous bioactive glass scaffold using primary human osteoblast (HOB) cells10.1016/j.biomaterials.2006.11.022 ↗
36. Anorganic Bovine Bone and Ceramic Analogs of Bone Mineral as Implants to Facilitate Bone Regeneration10.1016/S0094-1298(20)31021-X ↗
37. In vitro evaluation of confinement, bioactivity, and degradation of a putty type bone substitute10.1016/j.mtcomm.2021.102105 ↗
38. Deproteinized bovine bone functionalized with the slow delivery of BMP-2 for the repair of critical-sized bone defects in sheep10.1016/j.bone.2013.05.017 ↗
39. Functionalization of deproteinized bovine bone with a coating-incorporated depot of BMP-2 renders the material efficiently osteoinductive and suppresses foreign-body reactivity10.1016/j.bone.2011.09.046 ↗
40. Deproteinized Bovine Bone Versus Beta-Tricalcium Phosphate in Sinus Augmentation Surgery: A Comparative Histologic and Histomorphometric Study
41. Porosity of 3D biomaterial scaffolds and osteogenesis10.1016/j.biomaterials.2005.02.002 ↗
42. A 3D printed TCP-HA structure as a new osteoconductive scaffold for vertical bone augmentation10.1111/clr.12503 ↗
43. Characterization and distribution of mechanically competent mineralized tissue in micropores of β-tricalcium phosphate bone substitutes10.1016/j.mattod.2017.02.002 ↗
44. Vaquette, C., Mitchell, J., and Ivanovski, S. (2022). Recent Advances in Vertical Alveolar Bone Augmentation Using Additive Manufacturing Technologies. Front. Bioeng. Biotechnol., 9.10.3389/fbioe.2021.798393 ↗
45. Baumer, V., Gunn, E., Riegle, V., Bailey, C., Shonkwiler, C., and Prawel, D. (2023). Robocasting of Ceramic Fischer–Koch S Scaffolds for Bone Tissue Engineering. J. Funct. Biomater., 14.10.3390/jfb14050251 ↗
46. Better ceramics through colloid chemistry10.1016/j.jeurceramsoc.2019.10.014 ↗
47. Multifunctional Mechanical Metamaterials Based on Triply Periodic Minimal Surface Lattices10.1002/adem.201900524 ↗
48. (2013). Test Methods for Determining Average Grain Size. Standard No. ASTM E113-13.
49. Askeland, D.R., Fulay, P.P., and Wright, W.J. (2011). The Science and Engineering of Materials, Cengage Learning. [6th ed.].
50. Preparation, chemistry and physical properties of bone-derived hydroxyapatite particles having a negative zeta potential10.1016/j.matchemphys.2011.11.051 ↗
51. Effect of the temperature and sintering time on the thermal, structural, morphological, and vibrational properties of hydroxyapatite derived from pig bone10.1016/j.ceramint.2017.03.046 ↗
52. Buddhachat, K., Klinhom, S., Siengdee, P., Brown, J.L., Nomsiri, R., Kaewmong, P., Thitaram, C., Mahakkanukrauh, P., and Nganvongpanit, K. (2016). Elemental Analysis of Bone, Teeth, Horn and Antler in Different Animal Species Using Non-Invasive Handheld X-Ray Fluorescence. PLoS ONE, 11.10.1371/journal.pone.0155458 ↗
53. Bone formation controlled by biologically relevant inorganic ions: Role and controlled delivery from phosphate-based glasses10.1016/j.addr.2012.05.015 ↗
54. Bioinorganics and biomaterials: Bone repair10.1016/j.actbio.2011.03.027 ↗
55. Solid-Liquid Interface10.1016/B978-0-12-375049-5.00003-7 ↗
56. Al-Azzam, N., and Alazzam, A. (2022). Micropatterning of cells via adjusting surface wettability using plasma treatment and graphene oxide deposition. PLoS ONE, 17.10.1371/journal.pone.0269914 ↗
57. McKinney, D., and Sigmund, W. (2013). Colloidal Processing Fundamentals. Handbook of Advanced Ceramics, Elsevier.10.1016/B978-0-12-385469-8.00049-6 ↗
58. The relationship between particle morphology and rheological properties in injectable nano-hydroxyapatite bone graft substitutes10.1016/j.msec.2017.02.170 ↗
59. Holmberg, K., Shah, D.O., and Schwuger, M.J. (2002). Handbook of Applied Surface and Colloid Chemistry, Wiley.
60. Colloidal processing and sintering of hydroxyapatite10.1016/j.matchemphys.2006.02.016 ↗
61. Pore size and pore volume effects on alumina and TCP ceramic scaffolds10.1016/S0928-4931(02)00129-7 ↗
62. Sintering of calcium phosphate bioceramics10.1016/j.actbio.2012.11.029 ↗
63. Laser stereolithography of ZrO2 toughened Al2O310.1016/j.jeurceramsoc.2003.12.024 ↗
64. The kinetics of surface area reduction during isothermal sintering of hydroxyapatite adsorbent10.1016/j.cej.2003.07.001 ↗
65. Synthesis of macroporous hydroxyapatite scaffolds for bone tissue engineering10.1002/jbm.10163 ↗
66. The effect of cyclic heat treatment on the physicochemical properties of bio hydroxyapatite from bovine bone10.1007/s10856-018-6061-5 ↗
67. Coarsening, densification, and grain growth during sintering of nano-sized powders—A perspective10.1016/j.ijrmhm.2016.09.004 ↗
68. An improvement in sintering property of β-tricalcium phosphate by addition of calcium pyrophosphate10.1016/S0142-9612(01)00201-0 ↗
69. Porous scaffolds for bone regeneration10.1016/j.jsamd.2020.01.007 ↗
70. Biomechanics of Trabecular Bone10.1146/annurev.bioeng.3.1.307 ↗
71. Oftadeh, R., Perez-Viloria, M., Villa-Camacho, J.C., Vaziri, A., and Nazarian, A. (2015). Biomechanics and Mechanobiology of Trabecular Bone: A Review. J. Biomech. Eng., 137.10.1115/1.4029176 ↗
72. Bone Mechanical Properties in Healthy and Diseased States10.1146/annurev-bioeng-062117-121139 ↗
73. Baumer, V., Isaacson, N., Kanakamedala, S., McGee, D., Kaze, I., and Prawel, D. (2024). Comparing ceramic Fischer-Koch-S and gyroid TPMS scaffolds for potential in bone tissue engineering. Front. Bioeng. Biotechnol., 12.10.3389/fbioe.2024.1410837 ↗
74. Fabrication, Properties and Applications of Dense Hydroxyapatite: A Review10.3390/jfb6041099 ↗