AFM Analysis of a Three-Point Flexure Tested, 3D Printing Definitive Restoration Material for Dentistry
Source abstract
Abstract
Background: Three-dimensional printing is a rapidly developing technology across all industries. In medicine recent developments include 3D bioprinting, personalized medication and custom prosthetics and implants. To ensure safety and long-term usability in a clinical setting, it is essential to understand material specific properties. This study aims to analyze possible surface changes of a commercially available and approved DLP 3D printed definitive restoration material for dentistry after three-point flexure testing. Furthermore, this study explores whether Atomic Force Microscopy (AFM) is a feasible method for examination of 3D printed dental materials in general. This is a pilot study, as there are currently no studies that analyze 3D printed dental materials using an AFM. Methods: The present study consisted of a pretest followed by the main test. The resulting break force of the preliminary test was used to determine the force used in the main test. The main test consisted of atomic force microscopy (AFM) surface analysis of the test specimen followed by a three-point flexure procedure. After bending, the same specimen was analyzed with the AFM again, to observe possible surface changes. Results: The mean root mean square (RMS) roughness of the segments with the most stress was 20.27 nm (±5.16) before bending, while it was 26.48 nm (±6.67) afterward. The corresponding mean roughness (Ra) values were 16.05 nm (±4.25) and 21.19 nm (±5.71) Conclusions: Under three-point flexure testing, the surface roughness increased significantly. The p-value for RMS roughness was p = 0.003, while it was p = 0.006 for Ra. Furthermore, this study showed that AFM surface analysis is a suitable procedure to investigate surface changes in 3D printed dental materials.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Dental materials and restorations · Force Microscopy Techniques and Applications · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Research Center for Digital Technologies in Dentistry and CAD/CAM, Department of Dentistry, Faculty of Medicine and Dentistry, Danube Private University, 3500 Krems, Austria
Department of Medicine, Faculty of Medicine and Dentistry, Danube Private University, 3500 Krems, Austria
References (67)
Show source-provided references
1. The history of 3D printing in healthcare10.1308/147363514X13990346756481 ↗
2. Savini, A., and Savini, G. (2015, January 18–19). A short history of 3D printing, a technological revolution just started. Proceedings of the 2015 ICOHTEC/IEEE International History Of High-Technologies and Their Socio-Cultural Contexts Conference (HISTELCON), Tel-Aviv, Israel.10.1109/HISTELCON.2015.7307314 ↗
3. An overview on 3D printing technology: Technological, materials, and applications10.1016/j.promfg.2019.06.089 ↗
4. Xu, D., Shi, J., Qiu, R., Lei, W., and Yu, W. (2023). Comparative Investigations on Properties of Three Kinds of FDM 3D-Printed Natural Plant Powder/Poly(lactic acid) Biocomposites. Polymers, 15.10.3390/polym15030557 ↗
5. Selema, A., Ibrahim, M.N., and Sergeant, P. (2022). Metal additive manufacturing for electrical machines: Technology review and latest advancements. Energies, 15.10.3390/en15031076 ↗
6. Pilipović, A. (2022). Polymers for 3D Printing, Elsevier.
7. The role of 3D printing in medical applications: A state of the art10.1155/2019/5340616 ↗
8. 3D bioprinting of human hollow organs10.1208/s12249-022-02279-9 ↗
9. Uboldi, M., Perrotta, C., Moscheni, C., Zecchini, S., Napoli, A., Castiglioni, C., Gazzaniga, A., Melocchi, A., and Zema, L. (2023). Insights into the Safety and Versatility of 4D Printed Intravesical Drug Delivery Systems. Pharmaceutics, 15.10.3390/pharmaceutics15030757 ↗
10. Application of Medical Imaging and 3D Printing Technology in Teaching the Handling of Novel Medicine in Periodontal Surgery
11. Schweiger, J., Edelhoff, D., and Güth, J.-F. (2021). 3D printing in digital prosthetic dentistry: An overview of recent developments in additive manufacturing. J. Clin. Med., 10.10.3390/jcm10092010 ↗
12. Li, Z., Wang, Q., and Liu, G. (2022). A Review of 3D Printed Bone Implants. Micromachines, 13.10.3390/mi13040528 ↗
13. 3D printing in dentistry10.1038/sj.bdj.2015.914 ↗
14. 3D printing in dentistry
15. Anadioti, E., Musharbash, L., Blatz, M.B., Papavasiliou, G., and Kamposiora, P. (2020). 3D printed complete removable dental prostheses: A narrative review. BMC Oral Health, 20.10.1186/s12903-020-01328-8 ↗
16. 3D printing in dentistry–exploring the new horizons10.1016/j.jds.2021.04.004 ↗
17. 3D printing restorative materials using a stereolithographic technique: A systematic review10.1016/j.dental.2020.11.030 ↗
18. Nesic, D., Schaefer, B.M., Sun, Y., Saulacic, N., and Sailer, I. (2020). 3D printing approach in dentistry: The future for personalized oral soft tissue regeneration. J. Clin. Med., 9.10.3390/jcm9072238 ↗
19. A review of 3D printing in dentistry: Technologies, affecting factors, and applications10.1155/2021/9950131 ↗
20. CAD/CAM-Systeme10.1007/s00715-013-0229-x ↗
21. Assessment of chair-side computer-aided design and computer-aided manufacturing restorations: A review of the literature
22. Bego (2022, July 05). Scientific Studies on VarseoSmile Crown Plus. Available online: https://www.bego.com/3d-printing/materials/varseosmile-crown-plus/scientific-studies/.
23. Bego (2022, July 05). VarseoSmile Temp. Available online: https://www.bego.com/3d-printing/materials/varseosmile-temp/.
24. Koletsi, D., Iliadi, A., Eliades, T., and Eliades, G. (2019). In vitro simulation and in vivo assessment of tooth wear: A meta-analysis of in vitro and clinical research. Materials, 12.10.3390/ma12213575 ↗
25. Surface roughness of high-performance polymers used for fixed implant-supported prostheses10.1016/j.prosdent.2020.11.029 ↗
26. Fatigue resistance of CAD/CAM resin composite molar crowns10.1016/j.dental.2015.12.005 ↗
27. Gwyddion (2022, July 05). Gwyddion. Available online: http://gwyddion.net/.
28. Gwyddion: An open-source software for SPM data analysis10.2478/s11534-011-0096-2 ↗
29. Nold, J., Wesemann, C., Rieg, L., Binder, L., Witkowski, S., Spies, B.C., and Kohal, R.J. (2021). Does printing orientation matter? In-vitro fracture strength of temporary fixed dental prostheses after a 1-year simulation in the artificial mouth. Materials, 14.10.3390/ma14020259 ↗
30. Mahalaxmi, S. (2013). Materials Used in Dentistry, Wolters Kluwer India Private Ltd.
31. The relation between impact strength and flexural strength of dental materials10.1016/j.jmbbm.2021.104658 ↗
32. Mechanics of the rate-dependent elastic–plastic deformation of glassy polymers from low to high strain rates10.1016/j.ijsolstr.2005.04.016 ↗
33. Cahn, R.W., Mughrabi, H., Haasen, P., and Kramer, E.J. (1993). Materials Science and Technology: Plastic Deformation and Fracture of Materials, VCH.
34. BEGO (2021, March 15). VarseoSmile Crown Plus: Gebrauchsanweisung. Available online: https://www.bego.com/fileadmin/user_downloads/Mediathek/3D-Druck/Materialien/DE_Gebrauchsanweisungen/VarseoSmileCrown-plus/de_20740_0002_ga_de.pdf.
35. Lubliner, J. (2008). Plasticity Theory, Courier Corporation.
36. Instruments, O. (2022, November 14). AFM: Exploring Tapping Mode and AM-FM. Available online: https://afm.oxinst.com/outreach/tapping-mode-for-afm-am-fm.
37. AG, N. (2022, November 14). How Does AFM Work?. Available online: https://www.nanosurf.com/en/support/afm-operating-principle.
38. AFM advanced modes for dental and biomedical applications10.1016/j.jmbbm.2022.105475 ↗
39. The influence of light-curing time on fluoride release, surface topography, and bacterial adhesion in resin-modified glass ionomer cements: AFM and SEM in vitro study10.1002/jemt.23723 ↗
40. Polymeric nanoparticles for endodontic therapy10.1016/j.jmbbm.2019.103606 ↗
41. Evaluation of developmentally hypomineralised enamel after surface pretreatment with Papacarie Duo gel and different etching modes: An in vitro SEM and AFM study10.1007/s40368-021-00671-w ↗
42. Research techniques made simple: Analysis of skin cell and tissue mechanics using atomic force microscopy10.1016/j.jid.2021.02.750 ↗
43. Enamel sample preparation for AFM: Influence on roughness and morphology10.1002/jemt.23073 ↗
44. Advances in atomic force microscopy10.1103/RevModPhys.75.949 ↗
45. Quantitative nano-mechanical mapping AFM-based method for elastic modulus and surface roughness measurements of model polymer infiltrated ceramics10.1016/j.dental.2022.03.002 ↗
46. Pivotal role of filler/matrix interface in dental composites
47. The filler content of the dental composite resins and their influence on different properties10.1002/jemt.21122 ↗
48. Composite materials: Composition, properties and clinical applications. A literature review
49. Keshavamurthy, R., Tambrallimath, V., Rajhi, A.A., Ahmed, R.M.S., Patil, A.Y., Yunus Khan, T.M., and Makannavar, R. (2021). Influence of Solid Lubricant Addition on Friction and Wear Response of 3D Printed Polymer Composites. Polymers, 13.10.3390/polym13172905 ↗
50. Next Generation Material for Denture Teeth and Denture Base Material: Limpet Teeth (LT) as an Alternative Reinforcement in Polymethylmethacrylate (PMMA)
51. The effect of dental restorative materials on dental biofilm10.1046/j.0909-8836.2001.101160.x ↗
52. The influence of abutment surface roughness on plaque accumulation and peri-implant mucositis10.1034/j.1600-0501.1996.070302.x ↗
53. Effects of aging on surface properties and adhesion of Streptococcus mutans on various fissure sealants10.1007/s00784-009-0256-6 ↗
54. In vivo and in vitro biofilm formation on two different titanium implant surfaces10.1111/j.1600-0501.2009.01815.x ↗
55. Surface characteristics and in vitro biofilm formation on glass ionomer and composite resin10.1016/S0142-9612(00)00204-0 ↗
56. Adhesion of Streptococcus mutans NCTC 10449 to artificial teeth: An in vitro study10.1016/S0022-3913(08)60212-7 ↗
57. Biofilm formation on the surface of modern implant abutment materials10.1111/clr.12454 ↗
58. Influence of surface properties of resin-based composites on in vitro Streptococcus mutans biofilm development10.1111/j.1600-0722.2012.00983.x ↗
59. Effect of surface roughness of porcelain on adhesion of bacteria and their synthesizing glucans10.1067/mpr.2000.107442 ↗
60. Relevance of surface characteristics in the adhesiveness of polymicrobial biofilms to crown restoration materials10.2334/josnusd.16-0758 ↗
61. Polyetheretherketone/nano-fluorohydroxyapatite composite with antimicrobial activity and osseointegration properties10.1016/j.biomaterials.2014.04.085 ↗
62. Study of oral microbial adhesion and biofilm formation on the surface of nano-fluorohydroxyapatite/polyetheretherketone composite
63. Surface properties of polyetheretherketone after different laboratory and chairside polishing protocols10.1016/j.prosdent.2016.06.016 ↗
64. Mechanical properties and filler fraction of dental composites10.1016/0109-5641(89)90128-0 ↗
65. Properties of microfilled composite resins as influenced by filler content10.1177/00220345850640021301 ↗
66. Contouring, finishing, and polishing Class 5 restorative materials
67. Factors affecting enamel and ceramic wear: A literature review10.1067/mpr.2002.123851 ↗