journal article·2023-10-08Open access

The Porosity Design and Deformation Behavior Analysis of Additively Manufactured Bone Scaffolds through Finite Element Modelling and Mechanical Property Investigations

Shummaila Rasheed, Waqas Akbar Lughmani, Muhammad Mahabat Khan, Dermot Brabazon, Muhannad Ahmed Obeidi, Inam Ul Ahad

Journal of Functional Biomaterials· Volume 14· Issue 10

Abstract

Additively manufactured synthetic bone scaffolds have emerged as promising candidates for the replacement and regeneration of damaged and diseased bones. By employing optimal pore architecture, including pore morphology, sizes, and porosities, 3D-printed scaffolds can closely mimic the mechanical properties of natural bone and withstand external loads. This study aims to investigate the deformation pattern exhibited by polymeric bone scaffolds fabricated using the PolyJet (PJ) 3D printing technique. Cubic and hexagonal closed-packed uniform scaffolds with porosities of 30%, 50%, and 70% are utilized in finite element (FE) models. The crushable foam plasticity model is employed to analyze the scaffolds’ mechanical response under quasi-static compression. Experimental validation of the FE results demonstrates a favorable agreement, with an average percentage error of 12.27% ± 7.1%. Moreover, the yield strength and elastic modulus of the scaffolds are evaluated and compared, revealing notable differences between cubic and hexagonal closed-packed designs. The 30%, 50%, and 70% porous cubic pore-shaped bone scaffolds exhibit significantly higher yield strengths of 46.89%, 58.29%, and 66.09%, respectively, compared to the hexagonal closed-packed bone scaffolds at percentage strains of 5%, 6%, and 7%. Similarly, the elastic modulus of the 30%, 50%, and 70% porous cubic pore-shaped bone scaffolds is 42.68%, 59.70%, and 58.18% higher, respectively, than the hexagonal closed-packed bone scaffolds at the same percentage strain levels. Furthermore, it is observed in comparison with our previous study the μSLA-printed bone scaffolds demonstrate 1.5 times higher elastic moduli and yield strengths compared to the PJ-printed bone scaffolds.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Bone Tissue Engineering Materials · Cellular and Composite Structures

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Capital University of Science and Technology, Islamabad 44000, Pakistan

Faculty of Mechanical Engineering, Ghulam Ishaq Khan Institute of Engineering Sciences and Technology, Topi 23460, Pakistan

I-Form, The SFI Research Centre for Advanced Manufacturing, School of Mechanical and Manufacturing Engineering, Dublin City University, 09 Dublin, Ireland

Funding

Science Foundation Ireland

References (35)

Show source-provided references
1. Advances in Porous Scaffold Design for Bone and Cartilage Tissue Engineering and Regeneration10.1089/ten.teb.2018.0119 ↗
2. Improving the finite element model accuracy of tissue engineering scaffolds produced by selective laser sintering10.1007/s10856-014-5376-0 ↗
3. Verma, R., Kumar, J., Singh, N.K., Rai, S.K., Saxena, K.K., and Xu, J. (2022). Design and Analysis of Biomedical Scaffolds Using TPMS-Based Porous Structures Inspired from Additive Manufacturing. Coatings, 12.10.3390/coatings12060839 ↗
4. Mukherjee, S., Dhara, S., and Saha, P. (2023). Design and Additive Manufacturing of Acetabular Implant with Continuously Graded Porosity. Bioengineering, 10.10.20944/preprints202304.0856.v1 ↗
5. Chocholata, P., Kulda, V., and Babuska, V. (2019). Fabrication of scaffolds for bone-tissue regeneration. Materials, 12.10.3390/ma12040568 ↗
6. Pan, C., Han, Y., and Lu, J. (2020). Design and Optimization of Lattice Structures: A Review. Appl. Sci., 10.10.3390/app10186374 ↗
7. Failure mechanisms of additively manufactured porous biomaterials: Effects of porosity and type of unit cell10.1016/j.jmbbm.2015.06.012 ↗
8. Rasheed, S., Lughmani, W.A., Obeidi, M.A., Brabazon, D., and Ahad, I.U. (2021). Additive manufacturing of bone scaffolds using polyjet and stereolithography techniques. Appl. Sci., 11.10.3390/app11167336 ↗
9. Freeform 3D printing of soft matters: Recent advances in technology for biomedical engineering10.1007/s13534-020-00171-8 ↗
10. VOLCO: A predictive model for 3D printed microarchitecture
11. A mechanical property evaluation of graded density Al-Si10-Mg lattice structures manufactured by selective laser melting10.1016/j.msea.2016.06.013 ↗
12. Compressive properties of functionally graded lattice structures manufactured by selective laser melting10.1016/j.matdes.2017.06.006 ↗
13. The relationships between deformation mechanisms and mechanical properties of additively manufactured porous biomaterials10.1016/j.jmbbm.2016.09.018 ↗
14. Microstructure and micro-hardness analyses of titanium alloy Ti-6Al-4V parts manufactured by selective laser melting10.1051/matecconf/20179403009 ↗
15. Influence of Layer Thickness on Internal Structure of Parts Manufactured from 316-L Steel Using SLM Technology10.4028/www.scientific.net/AMM.809-810.369 ↗
16. Some Considerations Regarding Micro Hardness of Parts Manufactured from 316-L Steel Using SLM Technology10.4028/www.scientific.net/AMM.760.515 ↗
17. Mechanical characterization of 3D printed polymers for fiber reinforced polymers processing10.1016/j.matdes.2017.01.050 ↗
18. A novel hybridised composite sandwich core with Glass, Kevlar and Zylon fibres–Investigation under low-velocity impact10.1016/j.ijimpeng.2019.103430 ↗
19. Gibson, L.J., and Ashby, M.F. (2014). Cellular Solids: Structure and Properties, Cambridge University Press. [2nd ed.].
20. Effective mechanical properties of lattice material fabricated by material extrusion additive manufacturing
21. Strength analysis and modeling of cellular lattice structures manufactured using selective laser melting for tooling applications10.1016/j.matdes.2016.05.020 ↗
22. 3D fiber-deposited scaffolds for tissue engineering: Influence of pores geometry and architecture on dynamic mechanical properties10.1016/j.biomaterials.2005.07.023 ↗
23. Investigating internal architecture effect in plastic deformation and failure for TPMS-based scaffolds using simulation methods and experimental procedure10.1016/j.msec.2014.07.047 ↗
24. Unravelling the Role of Mechanical Stimuli in Regulating Cell Fate During Osteochondral Defect Repair10.1007/s10439-016-1664-9 ↗
25. Woo Jung, J., Yi, H.G., Kang, T.Y., Yong, W.J., Jin, S., Yun, W.S., and Cho, D.W. (2013). Evaluation of the effective diffusivity of a freeform fabricated scaffold using computational simulation. J. Biomech. Eng., 135.10.1115/1.4024570 ↗
26. Finite element modelling of the compressive response of lattice structures manufactured using the selective laser melting technique10.1016/j.ijmecsci.2012.12.004 ↗
27. Identification of a crushable foam material model and application to strength and damage prediction of human femur and vertebral body10.1016/j.jmbbm.2013.04.026 ↗
28. Characterization of polymeric structural foams under compressive impact loading by means of energy-absorption diagram10.1016/S0734-743X(00)00060-9 ↗
29. Development of a crushable foam model for human trabecular bone10.1016/j.medengphy.2021.08.009 ↗
30. Rimington, R.P., Capel, A.J., Player, D.J., Bibb, R.J., Christie, S.D., and Lewis, M.P. (2018). Feasibility and Biocompatibility of 3D-Printed Photopolymerized and Laser Sintered Polymers for Neuronal, Myogenic, and Hepatic Cell Types. Macromol. Biosci., 18.10.1002/mabi.201800113 ↗
31. Evaluation and optimization of PolyJet 3D-printed materials for cell culture studies10.1007/s00216-022-03991-y ↗
32. Villath, A.U. (2017). Investigation of Surface, Mechanical and Biocompatibility Properties of Post-Processing Methods on 3D Printed Models Intended for Clinical Applications. [Ph.D. Thesis, State University of New York at Buffalo].
33. 3D printing for the design and fabrication of polymer-based gradient scaffolds10.1016/j.actbio.2017.03.030 ↗
34. Mechanical behavior of a soft hydrogel reinforced with three-dimensional printed microfibre scaffolds10.1038/s41598-018-19502-y ↗
35. Hendrikson, W., van Blitterswijk, C., Rouwkema, J., and Moroni, L. (2017). The use of finite element analyses to design and fabricate three-dimensional scaffolds for skeletal tissue engineering. Front. Bioeng. Biotechnol., 5.10.3389/fbioe.2017.00030 ↗