journal article·2023-04-05Open access

Developing PMMA/Coffee Husk Green Composites to Meet the Individual Requirements of People with Disabilities: Hip Spacer Case Study

Ahmed Fouly, Ibrahim A. Alnaser, Abdulaziz K. Assaifan, Hany S. Abdo

Abstract

When replacing a damaged artificial hip joint, treatment involves using antibiotic-laced bone cement as a spacer. One of the most popular materials used for spacers is PMMA; however, it has limitations in terms of mechanical and tribological properties. To overcome such limitations, the current paper proposes utilizing a natural filler, coffee husk, as a reinforcement for PMMA. The coffee husk filler was first prepared using the ball-milling technique. PMMA composites with varying weight fractions of coffee husk (0, 2, 4, 6, and 8 wt.%) were prepared. The hardness was measured to estimate the mechanical properties of the produced composites, and the compression test was utilized to estimate the Young modulus and compressive yield strength. Furthermore, the tribological properties of the composites were evaluated by measuring the friction coefficient and wear by rubbing the composite samples against stainless steel and cow bone counterparts under different normal loads. The wear mechanisms were identified via scanning electron microscopy. Finally, a finite element model for the hip joint was built to investigate the load-carrying capacity of the composites under human loading conditions. The results show that incorporating coffee husk particles can enhance both the mechanical and tribological properties of the PMMA composites. The finite element results are consistent with the experimental findings, indicating the potential of the coffee husk as a promising filler material for enhancing the performance of PMMA-based biomaterials.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Natural Fiber Reinforced Composites · Tribology and Wear Analysis · biodegradable polymer synthesis and properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mechanical Engineering Department, College of Engineering, King Saud University, Riyadh 11421, Saudi Arabia

The King Salman Center for Disability Research, Riyadh 11421, Saudi Arabia

Department of Production Engineering and Mechanical Design, Faculty of Engineering, Minia University, Minya 61519, Egypt

Center of Excellence for Research in Engineering Materials (CEREM), King Saud University, P.O. Box 800, Riyadh 11421, Saudi Arabia

King Abdullah Institute for Nanotechnology, King Saud University, P.O. Box 2455, Riyadh 11451, Saudi Arabia

Biomedical Technology Department, College of Applied Medical Sciences, King Saud University, Riyadh 12372, Saudi Arabia

Mechanical Design and Materials Department, Faculty of Energy Engineering, Aswan University, Aswan 81521, Egypt

Funding

King Salman Center for Disability Research

References (46)

Show source-provided references
1. Investigations on the wear behaviour of the temporary PMMA-based hip Spacer-G®10.1243/095441103762597665 ↗
2. Fatigue testing and performance of acrylic bone-cement materials: State-of-the-art review10.1002/jbm.b.10018 ↗
3. Meani, E., Romanò, C., Crosby, L., and Hofmann, G. (2007). Infection and Local Treatment in Orthopedic Surgery, Springer.10.1007/978-3-540-47999-4 ↗
4. Hip spacers in two-stage revision for periprosthetic joint infection: A review of literature10.1055/s-0039-1697608 ↗
5. Development of a reinforced PMMA-based hip spacer adapted to patients’ needs10.1016/j.medengphy.2009.05.004 ↗
6. Mechanical and Tribological Characteristics of PMMA Reinforced by Natural Materials
7. Fouly, A., Ibrahim, A.M.M., Sherif, E.-S.M., FathEl-Bab, A.M., and Badran, A.H. (2021). Effect of low hydroxyapatite loading fraction on the mechanical and tribological characteristics of poly (methyl methacrylate) nanocomposites for dentures. Polymers, 13.10.3390/polym13060857 ↗
8. Effect of high-pressure polymerization on mechanical properties of PMMA denture base resin10.1016/j.jmbbm.2012.12.011 ↗
9. Mechanical properties of PMMA denture base reinforced by nitrile rubber particles with Al2O3/YSZ fillers10.1016/j.promfg.2015.07.053 ↗
10. Intraoperative unfractionated heparin before femoral component cementation should be avoided in femoral neck fracture treated with hybrid total hip arthroplasty
11. Effect of phosphate group addition on the properties of denture base resins10.1016/S0022-3913(08)60210-3 ↗
12. Application of plasma technologies in fibre-reinforced polymer composites: A review of recent developments10.1016/S1359-835X(96)00097-8 ↗
13. Mechanical and tribological properties of PMMA-sea shell based biocomposite for dental application10.1016/j.mspro.2014.07.234 ↗
14. Impact strength, fracture toughness and hardness improvement of PMMA denture base through addition of nitrile rubber/ceramic fillers10.1016/j.sjdr.2016.04.004 ↗
15. Influence of various metal oxides on mechanical and physical properties of heat-cured polymethyl methacrylate denture base resins10.4047/jap.2013.5.3.241 ↗
16. Fouly, A., Abdo, H.S., Seikh, A.H., Alluhydan, K., Alkhammash, H.I., Alnaser, I.A., and Abdo, M.S. (2021). Evaluation of mechanical and tribological properties of corn cob-reinforced epoxy-based composites—Theoretical and experimental study. Polymers, 13.10.3390/polym13244407 ↗
17. Mitra, B.C. (2014). Environment Friendly composite materials: Biocomposites and Green composites. Def. Sci. J., 64.10.14429/dsj.64.7323 ↗
18. Fouly, A., Alnaser, I.A., Assaifan, A.K., and Abdo, H.S. (2022). Evaluating the performance of 3D-printed PLA reinforced with date pit particles for its suitability as an acetabular liner in artificial hip joints. Polymers, 14.10.3390/polym14163321 ↗
19. Flexural properties of poly (Methyl Methacrylate) resin reinforced with oil palm empty fruit bunch fibers: A preliminary finding10.1111/jopr.12191 ↗
20. Preparation and investigation of some properties of acrylic resin reinforced with siwak fiber used for denture base applications10.24017/science.2017.3.53 ↗
21. Comparative Analysis of the Coffee and Cocoa Industry By-Products on the Performance of Polyethylene-Based Composites10.1007/s12649-023-02041-7 ↗
22. Mazzanti, V., Malagutti, L., Santoni, A., Sbardella, F., Calzolari, A., Sarasini, F., and Mollica, F. (2020). Correlation between Mechanical Properties and Processing Conditions in Rubber-Toughened Wood Polymer Composites. Polymers, 12.10.3390/polym12051170 ↗
23. In vitro antioxidant and ex vivo protective activities of green and roasted coffee10.1021/jf990510g ↗
24. The ‘Latte Revolution’? Regulation, Markets and Consumption in the Global Coffee Chain10.1016/S0305-750X(02)00032-3 ↗
25. Sustainable management of coffee industry by-products and value addition—A review10.1016/j.resconrec.2012.06.005 ↗
26. Production, composition, and application of coffee and its industrial residues10.1007/s11947-011-0565-z ↗
27. Use of shore hardness tests for in-process properties estimation/monitoring of silicone rubbers10.1016/j.msec.2015.05.013 ↗
28. Mechanical, in vitro corrosion and bioactivity performance of Mg based composite for orthopedic implant applications: Influence of Sn and HA addition10.1016/j.bea.2022.100033 ↗
29. Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus1
30. Standardized Loads Acting in Hip Implants10.1371/journal.pone.0155612 ↗
31. Preparation and characterization of pristine PMMA and PVDF thin film using solution casting process for optoelectronic devices10.18311/jsst/2017/6215 ↗
32. Influence of titanium oxide nanoparticles on the physical and thermomechanical behavior of poly methyl methacrylate (PMMA): A denture base resin10.1166/sam.2017.3087 ↗
33. Isolation and characterisation of microcrystalline cellulose and cellulose nanocrystals from coffee husk and comparative study with rice husk10.1016/j.carbpol.2018.03.022 ↗
34. Characterization of coffee parchment and innovative steam explosion treatment to obtain microfibrillated cellulose as potential composite reinforcement10.1016/j.jmrt.2020.05.099 ↗
35. Isolation and structural characterization of cellulose nanocrystals extracted from garlic straw residues10.1016/j.indcrop.2016.04.060 ↗
36. Nurazzi, N.M., Asyraf, M.R.M., Rayung, M., Norrrahim, M.N.F., Shazleen, S.S., Rani, M.S.A., Shafi, A.R., Aisyah, H.A., Radzi, M.H.M., and Sabaruddin, F.A. (2021). Thermogravimetric analysis properties of cellulosic natural fiber polymer composites: A review on influence of chemical treatments. Polymers, 13.10.3390/polym13162710 ↗
37. High volume-fraction silk fabric reinforcements can improve the key mechanical properties of epoxy resin composites10.1016/j.matdes.2016.06.128 ↗
38. Enhancing the tribological performance of epoxy composites utilizing carbon nano fibers additives for journal bearings10.1088/2053-1591/aadcdc ↗
39. A numerical analysis of the contact stress distribution and physical modelling of abrasive wear in the tram wheel-frog system10.1016/j.wear.2015.02.018 ↗
40. Preparation of aluminium-fly ash particulate composite by powder metallurgy technique10.1023/A:1018625118090 ↗
41. (2023, March 19). Effect of Nanoparticles on the Tribological Behaviour…—Google Scholar. Available online: https://scholar.google.com/scholar?hl=en&as_sdt=0%2C5&q=Effect+of+nanoparticles+on+the+tribological+behaviour+of+short+carbon+fibre+reinforced+poly+%28etherimide%29+composites&btnG=.
42. Tribological properties of short carbon fibers reinforced epoxy composites10.1007/s40544-014-0043-5 ↗
43. Enhancing the tribological properties of NiAl based nano-composites for aerospace bearing applications10.1088/2053-1591/ab2028 ↗
44. Mechanical properties of polycondensate epoxy nanocomposites filled with Ag nanoparticles synthesized in situ10.1016/j.matpr.2020.02.138 ↗
45. The effect of surface texturing on reducing the friction and wear of steel under lubricated sliding contact10.1016/j.apsusc.2013.02.013 ↗
46. An overview of the delamination theory of wear10.1016/0043-1648(77)90081-3 ↗