journal article·2024-08-22Open access

Temperature Changes (ΔT) in Correlation with Number of Implant Osteotomy Preparations in Human Cadaver Tibiae, Comparing Osseodensification (OD) Burs in Clockwise (CW) versus Counterclockwise (CCW) Mode

Nikolaos Soldatos, Amanda Heydari, LeRoy Horton, Shayda Sarrami, Luke Nordlie, Dongseok Choi, Robin Weltman

Abstract

(1) Background: OD burs are used in two different modes: (i) CW and (ii) CCW. The purpose of the study was to evaluate the ΔT during the preparation of implant osteotomies in a four-way interaction. (2) Methods: Three hundred and sixty osteotomies were prepared at 12 mm depth in human cadaver tibiae. The ΔT values were calculated similarly to the method used in two previous studies carried out by our group. Four different variables were evaluated for their effect on ΔT. (3) Results: A four-way interaction was observed in the CCW mode, allowing for 1000 RPM to have the least effect in both modes. However, in the CCW mode the use of 3.0 and 4.0 burs after 23 osteotomies showed a statistically significant increase in ΔT, and significant chatter, compared to the CW mode. In the CCW mode, the ΔT was increased significantly as the diameter of the burs increased in 800 and 1200 RPM. (4) Conclusions: The synergistic effect of drills’ diameter, CCW mode, 800 and 1200 RPM, and bur usage (over 23 times) had a significant effect on ΔT, which exceeded 47 °C. One thousand (1000) RPM had the least effect in both modes. The 3.0 and 4.0 burs in the CCW mode drastically increased the temperature and produced significant chatter.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dental Implant Techniques and Outcomes · Orthopaedic implants and arthroplasty · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Regenerative and Reconstructive Sciences, School of Dentistry, Oregon Health Science University (OHSU), 2730 SW Moody Ave., Portland, OR 97201, USA

Department of Oral Rehabilitation and Biosciences, School of Dentistry, Oregon Health Science University (OHSU), 2730 SW Moody Ave., Portland, OR 97201, USA

OHSU-PSU School of Public Health, Oregon Health & Science University, 1810 SW 5th Ave, Portland, OR 97201, USA

Department of Clinical Sciences, School of Dental Medicine, University of Nevada Las Vegas (UNLV), 1001 Shadow Ln., Las Vegas, NV 89106, USA

References (48)

Show source-provided references
1. Osseointegrated titanium implants. Requirements for ensuring a long-lasting, direct bone-to-implant anchorage in man10.3109/17453678108991776 ↗
2. Does bone mineral density influence the primary stability of dental implants? A systematic review10.1111/j.1600-0501.2011.02228.x ↗
3. Primary stability, insertion torque and bone density of cylindrical implant ad modum Brånemark: Is there a relationship? An in vitro study10.1111/j.1600-0501.2010.02036.x ↗
4. Two alternative surgical techniques for enhancing primary implant stability in the posterior maxilla: A clinical study including bone density, insertion torque, and resonance frequency analysis data10.1111/j.1708-8208.2008.00084.x ↗
5. Effect of bone quality and implant surgical technique on implant stability quotient (ISQ) value10.4047/jap.2011.3.1.10 ↗
6. Correlation between placement torque and survival of single-tooth implants
7. Correlation between initial BIC and the Insertion Torque/Depth Integral Recorded with an Instantaneous Torque- Measuring Implant Motor: An in vivo Study
8. A novel osseous densification approach in implant osteotomy preparation to increase biomechanical primary stability, bone mineral density, and bone-to-implant contact10.11607/jomi.4817 ↗
9. Biomechanical and histologic basis of osseodensification drilling for endosteal implant placement in low density bone. An experimental study in sheep10.1016/j.jmbbm.2016.06.007 ↗
10. Effects on ridge dimensions, bone density, and implant primary stability with osseodensification approach in implant osteotomy preparation10.11607/jomi.8540 ↗
11. Insertion and removal torque of dental implants placed using different drilling protocols: An experimental study on artificial bone substitutes10.1111/jopr.13607 ↗
12. Radiographical and histological characteristics of submerged and non-submerged titanium implants. An experimental study in the Labrador dog10.1034/j.1600-0501.1996.070103.x ↗
13. The causes of early implant bone loss: Myth or science?10.1902/jop.2002.73.3.322 ↗
14. Influence of Different Operatory Setups on Implant Survival Rate: A Retrospective Clinical Study10.1111/j.1708-8208.2008.00123.x ↗
15. Heat Production by 3 Implant Drill Systems after Repeated Drilling and Sterilization10.1016/j.joms.2005.10.011 ↗
16. Investigation of the effect of movement and irrigation systems on temperature in the conventional drilling of cortical bone10.1016/j.bjoms.2012.10.023 ↗
17. Study of temperature variation in cortical bone during osteotomies with trephine drills10.1007/s00784-013-1163-4 ↗
18. The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: A study of drill durability
19. Influence of tool geometry on drilling performance of cortical and trabecular bone10.1016/j.medengphy.2012.12.004 ↗
20. Heat caused by drilling cortical bone. Temperature measured in vivo in patients and animals10.3109/17453678408992410 ↗
21. The effect of irrigation on osteotomy depth and bur diameter
22. The effect of load on heat production, thermal effects, and expenditure of time during implant site preparation—An experimental ex vivo comparison between piezosurgery and conventional drilling10.1111/clr.12077 ↗
23. Microcirculation in grafted bone
24. Influence of multiple use of Timedur-titanium cannon drills: Thermal response and scanning electron microscopic findings
25. Thermal effects of a combined irrigation method during implant site drilling. A standardized in vitro study using a bovine rib model10.1111/clr.12032 ↗
26. Soldatos, N., Pham, H., Fakhouri, W.D., Ngo, B., Lampropoulos, P., Tran, T., and Weltman, R. (2022). Temperature changes during implant osteotomy preparations in human cadaver tibiae comparing MIS® straight drills with Densah® burs. Genes, 13.10.3390/genes13101716 ↗
27. Comparison of heat production and bone architecture changes in the implant site preparation with compressive osteotomes, osseodensification technique, piezoelectric devices, and standard drills: An ex vivo study on porcine ribs10.1007/s10266-022-00730-8 ↗
28. Mechanical properties of trabecular bone in the human mandible: Implications for dental implant treatment planning and surgical placement10.1016/S0278-2391(99)90437-8 ↗
29. Soldatos, N., Nelson-Rabe, L., Palanker, N., Angelov, N., Romanos, G., and Weltman, R. (2022). Temperature changes during implant osteotomy preparations in fresh human cadaver tibiae, comparing straight with tapered drills. Materials, 15.10.3390/ma15072369 ↗
30. R Core Team (2021). R: A Language and Environment for Statistical Computing, R Foundation for Statistical Computing. Available online: https://www.R-project.org/.
31. Temperatures during drilling for the placement of implants using the osseointegration technique10.1016/0278-2391(86)90006-6 ↗
32. The effect of heat on bone regeneration: An experimental study in the rabbit using the bone growth chamber10.1016/0278-2391(84)90417-8 ↗
33. An in vitro study of temperature changes in type 4 bone during implant placement: Bone condensing versus bone drilling. Oral Surg10.1016/j.tripleo.2010.08.010 ↗
34. Heat production during different ultrasonic and conventional osteotomy preparations for dental implants10.1111/j.1600-0501.2010.02126.x ↗
35. Comparison of heat generation between internally guided (cannulated) single drill and traditional sequential drilling with and without a drill guide for dental implants
36. Effect of temperature on the dental implant osseointegration development in low-density bone: An in vivo histological evaluation10.1097/ID.0000000000000204 ↗
37. Porosity of human mandibular condylar bone10.1111/j.1469-7580.2007.00693.x ↗
38. Temperature Changes during Implant Osteotomies Utilizing three different implant systems: A pilot study
39. Compacted cancellous bone has a spring-back effect10.1080/00016470310018018 ↗
40. Evaluation of bone heating, drill deformation, and drill roughness after implant osteotomy: Guided surgery and classic drilling procedure10.11607/jomi.2919 ↗
41. Intraosseous heat generation during osteotomy performed freehand and through template with an integrated metal guide sleeve: An in vitro study10.1097/ID.0000000000000763 ↗
42. Temperatures measured in human cortical bone when drilling10.2106/00004623-197254020-00008 ↗
43. Temperature changes in bovine mandibular bone during implant site preparation: An assessment using infra-red thermography10.1016/0300-5712(95)00072-0 ↗
44. Effect of surgical drill guide on heat generated from implant drilling10.1016/j.joms.2009.07.056 ↗
45. Thermal changes and drill wear in bovine bone during implant site preparation. A comparative in vitro study: Twisted stainless steel and ceramic drills10.1111/j.1600-0501.2011.02248.x ↗
46. Descriptive study of the longevity of dental implant surgery drills10.1111/j.1708-8208.2009.00205.x ↗
47. Infrared Thermographic Evaluation of Temperature Modifications Induced during Implant Site Preparation with Cylindrical versus Conical Drills10.1111/j.1708-8208.2009.00209.x ↗
48. Yu, K., Iwata, S., Ohnishi, K., Usuda, S., Nakagawa, T., and Kawana, H. (2014, January 14–16). Modeling and experimentation of drilling vibration for implant cutting force presenting system. Proceedings of the 2014 IEEE 13th International Workshop on Advanced Motion Control (AMC), Yokohama, Japan.10.1109/AMC.2014.6823368 ↗