journal article·2024-08-21Open access

Mechanical Assessment of Denture Polymers Processing Technologies

Cristina Modiga, Andreea Stoia, Marius Traian Leretter, Ana Codruţa Chiş, Andreea-Violeta Ardelean, Edward-Ronald Azar, Gabriel Kapor, Daniela-Maria Pop, Mihai Romînu, Cosmin Sinescu, Meda-Lavinia Negruţiu, Emanuela-Lidia Petrescu

Abstract

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. The compressive strength of dentures manufactured using various technologies will be investigated. Methods: Traditional, injection molding, and additive and subtractive CAD/CAM processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a compressive mechanical test, which reveals the differences in compressive strength. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded, as well as the breaking energy. The mean force required to break the dentures for each processing technology is as follows: 4.54 kN for traditional packing-press technique, 17.92 kN for the injection molding technique, 1.51 kN for the additive CAD/CAM dentures, and 5.9 kN for the subtractive CAD/CAM dentures. Conclusions: The best results were obtained in the case of the thermoplastic injection system and the worst results were recorded in the case of 3D printed samples. Another important aspect depicted is the standard deviation for each group, which reveal a relatively unstable property for the thermoplastic injected dentures. Good results here in terms of absolute property and stability of the property can be conferred to CAD/CAM milled group.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Injection Molding Process and Properties · Dental materials and restorations · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Prostheses Technology and Dental Materials, Faculty of Dental Medicine, University of Medicine and Pharmacy “Victor Babeş” Timișoara, Eftimie Murgu Sq. No. 2, 300041 Timişoara, Romania

Research Center in Dental Medicine Using Conventional and Alternative Technologies, University of Medicine and Pharmacy “Victor Babeş” Timișoara, Eftimie Murgu Sq. No. 2, 300041 Timişoara, Romania

Department of Mechanics and Strength of Materials, “Politehnica” University of Timisoara, 1 Mihai Viteazu Ave., 300222 Timişoara, Romania

Department of Prosthodontics, Faculty of Dental Medicine, University of Medicine and Pharmacy “Victor Babeş” Timișoara, Bd. Revolutiei din 1989, Nr. 9, 300041 Timişoara, Romania

Research Institute for Biosafety and Bioengineering, The King Michael I University of Life Sciences, 119 Aradului Road, 300645 Timişoara, Romania

Funding

”Victor Babeş” University of Medicine and Pharmacy of Timişoara, Romania

References (40)

Show source-provided references
2. Komagamine, Y., Suzuki, H., Iwaki, M., Minakuchi, S., and Kanazawa, M. (2023). Effect of New Complete Dentures and Simple Die-tary Advice on Cognitive Screening Test among Edentulous Older Adults: A Randomized Controlled Trial. J. Clin. Med., 12.10.3390/jcm12144709 ↗
3. Oral diseases: A global public health challenge10.1016/S0140-6736(19)31146-8 ↗
4. United Nations (2019). World Population Prospects 2019: Highlights, United Nations.
5. Mechanical properties of the modified denture base materials and polymerization methods: A systematic review10.3390/ijms23105737 ↗
6. A review of the properties and applications of poly (methyl methacrylate) (PMMA)10.1080/15583724.2015.1031377 ↗
7. Flexural strength of denture base acrylic resins processed by conventional and CAD-CAM methods10.1016/j.prosdent.2019.03.010 ↗
8. An investigation into the transverse and impact strength of `high strength’ denture base acrylic resins10.1046/j.1365-2842.2002.00830.x ↗
9. Zafar, M.S. (2020). Prosthodontic Applications of Polymethyl Methacrylate (PMMA): An Update. Polymers, 12.10.3390/polym12102299 ↗
10. Mechanical properties of polyamide versus different PMMA denture base materials: Polyamide as denture base material10.1111/j.1532-849X.2011.00804.x ↗
11. Comparative study of the transverse strength of three denture base materials10.1016/j.jdent.2007.09.006 ↗
12. Compressive Strength of Three Types of Heat-Cure Acrylic Resins: Acropars, Acrosun, and Meliodent10.52547/jrdms.6.4.14 ↗
13. Zidan, S., Silikas, N., Alhotan, A., Haider, J., and Yates, J. (2019). Investigating the mechanical properties of zro2-impregnated pmma nanocomposite for denture-based applications. Materials, 12.10.3390/ma12081344 ↗
14. Influence of acrylamide monomer addition to the acrylic denture-base resins on mechanical and physical properties10.1038/ijos.2013.69 ↗
15. Li, G.H., Chen, S., Grymak, A., Waddell, J.N., Kim, J.J., and Choi, J.J.E. (2021). Fibre-reinforced and repaired PMMA denture base resin: Effect of placement on the flexural strength and load-bearing capacity. J. Mech. Behav. Biomed. Mater., 124.10.1016/j.jmbbm.2021.104828 ↗
16. Flexural strength of polymethyl methacrylate copolymers as a denture base resin10.4012/dmj.2018-393 ↗
17. Effect of Novel Cycloaliphatic Comonomer on the Flexural and Impact Strength of Heat-Cure Denture Base Resin10.2334/josnusd.19-0493 ↗
18. Investigation of flexural strength and cytotoxicity of acrylic resin copolymers by using different polymerization methods10.4047/jap.2015.7.2.98 ↗
19. Effect of polyimide addition on mechanical properties of PMMA-based denture material10.4012/dmj.2016-261 ↗
20. Use of CAD-CAM technology for the fabrication of Yilmaz, B.; Azak, A.N.; Alp, G.; Ekşi, H. Use of CAD-CAM technology for the fabrication of complete dentures: An alternative technique10.1016/j.prosdent.2016.10.016 ↗
21. Advantages of CAD/CAM versus conventional complete dentures—A review10.3889/oamjms.2018.308 ↗
22. Mechanical properties of polymethyl methacrylate as a denture base: Conventional versus CAD-CAM resin—A systematic review and meta-analysis of in vitro studies10.1016/j.prosdent.2021.03.018 ↗
23. Comparison of mechanical properties of 3d-printed, cad/cam, and conventional denture base materials10.1111/jopr.13175 ↗
24. Bratu, D., Ieremia, L., Uram-uculescu, S., Bortun, C., Bratu, E., Fabricky, M., Goguta, L., Jivanescu, A., Leretter, M., and Marcauteanu, C. (2003). Bazele Clinice si Tehnice ale Protezarii Edentatiei Totale, Ed.Imprimeria de Vest.
25. Crăciunescu, E.L., Romînu, M., Negruţiu, M.L., Sinescu, C., Novac, A.C., Caplar, B.D., and Pop, D.M. (2023). Indirect Restorative Polymeric Dental Materials. Advances in Dentures—Prosthetic Solutions, Materials and Technologies, IntechOpen.
26. The impact of fabrication methodologies on the flexural strength of complete dentures: An investigation into technological influences
27. Zupancic Cepic, L., Gruber, R., Eder, J., Vaskovich, T., Schmid-Schwap, M., and Kundi, M. (2023). Digital versus Conventional Dentures: A Prospective, Randomized Cross-Over Study on Clinical Efficiency and Patient Satisfaction. J. Clin. Med., 12.10.3390/jcm12020434 ↗
28. Ardelean, L.C., Rusu, L.C., Tigmeanu, C.V., Negrutiu, M.L., and Pop, D.M. (2023). Advances in Dentures: Novel Polymeric Materials and Manufacturing Technologies. Advances in Dentures—Prosthetic Solutions, Materials and Technologies, IntechOpen.
29. Economic and Clinical Impact of Digitally Produced Dentures10.1111/jopr.13283 ↗
30. A review on clinical use of CAD/CAM and 3D printed dentures
31. Jain, S., Sayed, M.E., Shetty, M., Alqahtani, S.M., Al Wadei, M.H.D., Gupta, S.G., Othman, A.A.A., Alshehri, A.H., Alqarni, H., and Mobarki, A.H. (2022). Physical and Mechanical Properties of 3D-Printed Provisional Crowns and Fixed Dental Prosthesis Resins Compared to CAD/CAM Milled and Conventional Provisional Resins: A Systematic Review and Meta-Analysis. Polymers, 14.10.3390/polym14132691 ↗
32. Comparison of the flexural and surface properties of milled, 3D-printed, and heat polymerized PMMA resins for denture bases: An in vitro study10.2186/jpr.JPR_D_21_00116 ↗
33. Comparison of denture base adaptation between CAD-CAM and conventional fabrication techniques10.1016/j.prosdent.2016.02.017 ↗
34. CAD-CAM milled versus rapidly prototyped (3D-printed) complete dentures: An in vitro evaluation of trueness10.1016/j.prosdent.2018.09.001 ↗
35. Evaluation of patient experience and satisfaction with CAD-CAM-fabricated complete denture: A retrospective survey study10.1016/j.prosdent.2016.01.034 ↗
36. (2021). Ling L, Ma Y, Malyala R, A novel CAD/CAM resin composite block with high mechanical properties. Dent. Mater., 37, 1150–1155.10.1016/j.dental.2021.03.006 ↗
37. Improving properties of a part fabricated by polymer-based powder bed fusion using a warm isostatic press (WIP) process10.1016/j.matdes.2022.111417 ↗
38. Hada, T., Kanazawa, M., Iwaki, M., Katheng, A., and Minakuchi, S. (2021). Comparison of Mechanical Properties of PMMA Disks for Digitally Designed Dentures. Polymers, 13.10.3390/polym13111745 ↗
39. Sfeatcu, R., Balgiu, B.A., Mihai, C., Petre, A., Pantea, M., and Tribus, L. (2022). Gender Differences in Oral Health: Self-Reported Attitudes, Values, Behaviours and Literacy among Romanian Adults. J. Pers. Med., 12.10.3390/jpm12101603 ↗
40. Grachev, D.I., Zolotnitsky, I.V., Stepanov, D.Y., Kozulin, A.A., Mustafaev, M.S., Deshev, A.V., Arutyunov, D.S., Tlupov, I.V., Panin, S.V., and Arutyunov, S.D. (2023). Ranking Technologies of Additive Manufacturing of Removable Complete Dentures by the Results of Their Mechanical Testing. Dent. J., 11.10.3390/dj11110265 ↗