Development of Novel Antibacterial Ti-Nb-Ga Alloys with Low Stiffness for Medical Implant Applications
Source abstract
Abstract
With the rising demand for medical implants and the dominance of implant-associated failures including infections, extensive research has been prompted into the development of novel biomaterials that can offer desirable characteristics. This study develops and evaluates new titanium-based alloys containing gallium additions with the aim of offering beneficial antibacterial properties while having a reduced stiffness level to minimise the effect of stress shielding when in contact with bone. The focus is on the microstructure, mechanical properties, antimicrobial activity, and cytocompatibility to inform the suitability of the designed alloys as biometals. Novel Ti-33Nb-xGa alloys (x = 3, 5 wt%) were produced via casting followed by homogenisation treatment, where all results were compared to the currently employed alloy Ti-6Al-4V. Optical microscopy, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) results depicted a single beta (β) phase microstructure in both Ga-containing alloys, where Ti-33Nb-5Ga was also dominated by dendritic alpha (α) phase grains in a β-phase matrix. EDS analysis indicated that the α-phase dendrites in Ti-33Nb-5Ga were enriched with titanium, while the β-phase was richer in niobium and gallium elements. Mechanical properties were measured using nanoindentation and microhardness methods, where the Young’s modulus for Ti-33Nb-3Ga and Ti-33Nb-5Ga was found to be 75.4 ± 2.4 and 67.2 ± 1.6 GPa, respectively, a significant reduction of 37% and 44% with respect to Ti-6Al-4V. This reduction helps address the disproportionate Young’s modulus between titanium implant components and cortical bone. Importantly, both alloys successfully achieved superior antimicrobial properties against Gram-negative P. aeruginosa and Gram-positive S. aureus bacteria. Antibacterial efficacy was noted at up to 90 ± 5% for the 3 wt% alloy and 95 ± 3% for the 5 wt% alloy. These findings signify a substantial enhancement of the antimicrobial performance when compared to Ti-6Al-4V which exhibited very small rates (up to 6.3 ± 1.5%). No cytotoxicity was observed in hGF cell lines over 24 h. Cell morphology and cytoskeleton distribution appeared to depict typical morphology with a prominent nucleus, elongated fibroblastic spindle-shaped morphology, and F-actin filamentous stress fibres in a well-defined structure of parallel bundles along the cellular axis. The developed alloys in this work have shown very promising results and are suggested to be further examined towards the use of orthopaedic implant components.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Orthopaedic implants and arthroplasty · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
College of Science and Engineering, Flinders University, Tonsley, SA 5042, Australia
College of Medicine and Public Health, Flinders University, Bedford Park, SA 5042, Australia
References (68)
Show source-provided references
1. Scialla, S., Martuscelli, G., Nappi, F., Singh, S.S.A., Iervolino, A., Larobina, D., Ambrosio, L., and Raucci, M.G. (2021). Trends in Managing Cardiac and Orthopaedic Device-Associated Infections by Using Therapeutic Biomaterials. Polymers, 13.10.3390/polym13101556 ↗
2. Effect of Zr and Sn on Young’s modulus and superelasticity of Ti-Nb-based alloys10.1016/j.msea.2006.09.051 ↗
3. A new antibacterial titanium-copper sintered alloy: Preparation and antibacterial property10.1016/j.msec.2013.06.016 ↗
4. Afzali, P., Ghomashchi, R., and Oskouei, R.H. (2019). On the Corrosion Behaviour of Low Modulus Titanium Alloys for Medical Implant Applications: A Review. Metals, 9.10.3390/met9080878 ↗
5. Fallahnezhad, K., Oskouei, R.H., Badnava, H., and Taylor, M. (2019). The Influence of Assembly Force on the Material Loss at the Metallic Head-Neck Junction of Hip Implants Subjected to Cyclic Fretting Wear. Metals, 9.10.3390/met9040422 ↗
6. Feyzi, M., Fallahnezhad, K., Taylor, M., and Hashemi, R. (2021). The mechanics of head-neck taper junctions: What do we know from finite element analysis?. J. Mech. Behav. Biomed. Mater., 116.10.1016/j.jmbbm.2021.104338 ↗
7. A finite element study on the mechanical response of the head-neck interface of hip implants under realistic forces and moments of daily activities: Part 1, level walking10.1016/j.jmbbm.2017.08.012 ↗
8. Alberta, L.A., Fortouna, Y., Vishnu, J., Pilz, S., Gebert, A., Lekka, C., Nielsch, K., and Calin, M. (2023). Effects of Ga on the structural, mechanical and electronic properties of ?-Ti-45Nb alloy by experiments and ab initio calculations. J. Mech. Behav. Biomed. Mater., 140.10.1016/j.jmbbm.2023.105728 ↗
9. The roles of oxygen content on microstructural transformation, mechanical properties and corrosion resistance of Ti-Nb-based biomedical alloys with different beta stabilities10.1016/j.matchar.2021.111122 ↗
10. Is aluminum exposure a risk factor for neurological disorders?10.4103/jrms.JRMS_921_17 ↗
11. Assessment of the genetic risks of a metallic alloy used in medical implants10.1590/S1415-47572010005000118 ↗
12. Kaur, S., Ghadirinejad, K., and Oskouei, R.H. (2019). An Overview on the Tribological Performance of Titanium Alloys with Surface Modifications for Biomedical Applications. Lubricants, 7.10.3390/lubricants7080065 ↗
13. Metallurgical Gallium Additions to Titanium Alloys Demonstrate a Strong Time-Increasing Antibacterial Activity without any Cellular Toxicity10.1021/acsbiomaterials.9b00147 ↗
14. Elastic softening of beta-type Ti-Nb alloys by indium (In) additions10.1016/j.jmbbm.2014.07.010 ↗
15. Ning, C.Q., Ding, D.Y., Dai, K.R., Zhai, W.Y., and Chen, L. (2010). The effect of Zr content on the microstructure, mechanical properties and cell attachment of Ti-35Nb-xZr alloys. Biomed. Mater., 5.10.1088/1748-6041/5/4/045006 ↗
16. Effect of niobium content on the microstructure and Young’s modulus of Ti-xNb-7Zr alloys for medical implants10.1016/j.jmbbm.2019.07.014 ↗
17. Mechanical compatibility of titanium implants in hard tissues10.1016/j.ics.2005.06.084 ↗
18. Electrochemical and biological characterization of Ti–Nb–Zr–Si alloy for orthopedic applications10.1038/s41598-023-29553-5 ↗
19. Surface film characterizations and electrochemical behavior of type I collagen-immobilized interconnected porous Ti–Nb–Zr–Sn alloy scaffolds in simulated inflammatory environment10.1016/j.jmrt.2022.11.077 ↗
20. Chen, X.G., Zhou, J.H., Qian, Y., and Zhao, L.Z. (2023). Antibacterial coatings on orthopedic implants. Mater. Today Bio, 19.10.1016/j.mtbio.2023.100586 ↗
21. The effect of silver or gallium doped titanium against the multidrug resistant Acinetobacter baumannii10.1016/j.biomaterials.2015.11.042 ↗
22. McHendrie, R., Xiao, W., Truong, V.K., and Hashemi, R. (2023). Gallium-Containing Materials and Their Potential within New-Generation Titanium Alloys for Biomedical Applications. Biomimetics, 8.10.3390/biomimetics8080573 ↗
23. Antimicrobial gallium-doped phosphate-based glasses10.1002/adfm.200700931 ↗
24. Tribocorrosion behavior of ?-type Ti-Nb-Ga alloys in a physiological solution10.1016/j.triboint.2023.108325 ↗
25. Novel low modulus beta-type Ti-Nb alloys by gallium and copper minor additions for antibacterial implant applications10.1016/j.jmrt.2022.08.111 ↗
26. Effect of oxygen addition and annealing time on microstructure and mechanical properties of Ti–34Nb alloy10.1007/s42243-021-00707-x ↗
27. Development of Ti-Nb-Zr alloys with high elastic admissible strain for temporary orthopedic devices10.1016/j.actbio.2015.03.023 ↗
28. Laser-deposited Ti-Nb-Zr-Ta orthopedic alloys10.1002/jbm.a.30694 ↗
29. Composition dependence of Young’s modulus in beta titanium binary alloys10.4028/www.scientific.net/MSF.426-432.3103 ↗
30. Vickers hardness of cast commercially pure titanium and Ti-6Al-4V alloy submitted to heat treatments10.1590/S0103-64402006000200008 ↗
31. Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion10.1016/j.msea.2018.08.094 ↗
32. Nanoindentation characterization on local plastic response of Ti-6Al-4V under high-load spherical indentation10.1016/j.jmrt.2019.06.009 ↗
33. Scanning Speed Effect on Mechanical Properties of Ti-6Al-4V Alloy Processed by Electron Beam Additive Manufacturing10.1016/j.promfg.2015.09.026 ↗
34. Development of microstructure and high hardness of Ti6Al4V alloy fabricated using laser beam powder bed fusion: A novel sub-transus heat treatment approach10.1016/j.jallcom.2022.168387 ↗
35. Nguyen, N.H., Lu, Z., Elbourne, A., Vasilev, K., Roohani, I., Truong, V.K., and Zreiqat, H. (2024). Engineering antibacterial bioceramics: Design principles and mechanisms of action. Mater. Today Bio, 26.10.1016/j.mtbio.2024.101069 ↗
36. Biofilm formation in Staphylococcus implant infections. A review of molecular mechanisms and implications for biofilm-resistant materials10.1016/j.biomaterials.2012.05.031 ↗
37. Emergence of antibiotic resistance Pseudomonas aeruginosa in intensive care unit; a critical review10.1016/j.gendis.2019.04.001 ↗
38. Alloy Design and Property Evaluation of new Ti-Cr-Nb Alloys10.1016/j.matdes.2011.06.052 ↗
39. Microstructure and Mechanical Properties of Ti-Nb Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering10.1007/s11665-019-04417-0 ↗
40. The Phase Transformations Induced by High-Pressure Torsion in Ti–Nb-Based Alloys10.1017/S1431927621012277 ↗
41. Sefer, B. (2014). Oxidation and Alpha–Case Phenomena in Titanium Alloys Used in Aerospace Industry: Ti–6Al–2Sn–4Zr–2Mo and Ti–6Al–4V, Department of Engineering Sciences and Mathematics, Luleå University of Technology.
42. Sefer, B., Roa, J., Mateo, A., Pederson, R., and Antti, M.-L. Evaluation of the Bulk and Alpha-Case Layer Properties in Ti-6Al-4V at Micro-And Nano-Metric Length Scale. Proceedings of the 13th World Conference on Titanium.
43. Lee, H.E., Wu, J.H., Chao, C.Y., Chang, Y.H., Du, J.K., Chen, K.K., and Chen, H.M. (2020). A Study of Low Young’s Modulus Ti-15Ta-15Nb Alloy Using TEM Analysis. Materials, 13.10.3390/ma13245694 ↗
44. Microstructural and mechanical characterization of Ti6Al4V refurbished parts obtained by laser metal deposition10.1016/j.msea.2015.07.029 ↗
45. Effect of minor gallium addition on corrosion, passivity, and antibacterial behaviour of novel β-type Ti–Nb alloys10.1016/j.jmrt.2023.06.219 ↗
46. Powder Metallurgy Processing of Ti-Nb Based Biomedical Alloys10.12693/APhysPolA.134.278 ↗
47. Titanium-Niobium (Ti-xNb) Alloys with High Nb Amounts for Applications in Biomaterials10.1590/1980-5373-mr-2020-0405 ↗
48. Correlations between aging heat treatment, ω phase precipitation and mechanical properties of a cast Ti–Nb alloy10.1016/j.matdes.2010.11.012 ↗
49. Synthesis and characterisation of a new superelastic Ti-25Ta-25Nb biomedical alloy10.1016/j.jmbbm.2010.06.007 ↗
50. Microstructural and mechanical characterization of biomedical Ti–Nb–Zr(–Ta) alloys10.1016/j.msea.2006.06.013 ↗
51. Selective laser melting of high-strength, low-modulus Ti–35Nb–7Zr–5Ta alloy10.1016/j.mtla.2020.100941 ↗
52. Antibacterial Longevity of a Novel Gallium Liquid Metal/Hydroxyapatite Composite Coating Fabricated by Plasma Spray10.1021/acsami.2c03695 ↗
53. Antimicrobial activity of metals: Mechanisms, molecular targets and applications10.1038/nrmicro3028 ↗
54. Gallium Complex-Functionalized P4HB Fibers: A Trojan Horse to Fight Bacterial Infection10.1021/acsabm.0c01221 ↗
55. Gallium disrupts bacterial iron metabolism and has therapeutic effects in mice and humans with lung infections10.1126/scitranslmed.aat7520 ↗
56. Gallium containing bioactive materials: A review of anticancer, antibacterial, and osteogenic properties
57. Biofilm formation on titanium implants counteracted by grafting gallium and silver ions10.1002/jbm.a.35270 ↗
58. Yamaguchi, S., Nath, S., Sugawara, Y., Divakarla, K., Das, T., Manos, J., Chrzanowski, W., Matsushita, T., and Kokubo, T. (2017). Two-in-One Biointerfaces-Antimicrobial and Bioactive Nanoporous Gallium Titanate Layers for Titanium Implants. Nanomaterials, 7.10.3390/nano7080229 ↗
59. Antibacterial and antifungal potential of Ga-bioactive glass and Ga-bioactive glass/polymeric hydrogel composites10.1002/jbm.b.33655 ↗
60. Self-healing polydimethylsiloxane antifouling coatings based on zwitterionic polyethylenimine-functionalized gallium nanodroplets10.1016/j.cej.2021.131019 ↗
61. Tetrazolium dyes as tools in cell biology: New insights into their cellular reduction10.1016/S1387-2656(05)11004-7 ↗
62. Nano-hydroxyapatite in oral care cosmetics: Characterization and cytotoxicity assessment10.1038/s41598-019-47491-z ↗
63. Mechanical Integration of Actin and Adhesion Dynamics in Cell Migration10.1146/annurev.cellbio.011209.122036 ↗
64. Biocompatibility assessment of biomaterials used in orthopedic devices: An overview (Review)10.3892/etm.2021.10750 ↗
65. Shape-transformable liquid metal nanoparticles in aqueous solution10.1039/C7SC00057J ↗
66. Transformable liquid-metal nanomedicine10.1038/ncomms10066 ↗
67. Advances in liquid metals for biomedical applications10.1039/C7CS00309A ↗
68. Liquid metal polymer composite: Flexible, conductive, biocompatible, and antimicrobial scaffold10.1002/jbm.b.34987 ↗