Rheological Properties, Surface Microhardness, and Dentin Shear Bond Strength of Resin-Modified Glass Ionomer Cements Containing Methacrylate-Functionalized Polyacids and Spherical Pre-Reacted Glass Fillers
Source abstract
Abstract
The aim of this study was to prepare experimental resin-modified glass ionomer cements (RMGICs) containing low levels of hydroxyethyl methacrylate (HEMA) for pulp protection. Liquid and powder phases of the experimental RMGICs were polyacid functionalized with methacrylate groups and spherical pre-reacted glass fillers (SPG). Two types of liquid phase containing 0 wt. % HEMA (CM liquid) or 5 wt. % HEMA (CMH liquid) were formulated. The experimental RMGICs were prepared by mixing SPG fillers with CM liquid (F1) or CMH liquid (F2). Rheological properties were examined using a strain-controlled rheometer (n = 5). The Vickers microhardness (n = 5) and dentin shear bond strength (SBS) (n = 10) of the materials were tested. Commercial pulp protection materials (Vitrebond and TheraCal LC) were used as comparisons. The viscosity and surface microhardness of F1 (22 m Pa·s, 18 VHN) and F2 (18 m Pa·s, 16 VHN) were significantly higher than those of Vitrebond (6 mPa·s, 6 VHN) and TheraCal (0.1 mPa·s, 7 VHN). The SBS of F1 (10.7 MPa) and F2 (11.9 MPa) was comparable to that of Vitrebond (15.4 MPa) but higher than that of TheraCal LC (5.6 MPa). The addition of 5 wt. % HEMA showed no significant effect on viscosity, surface microhardness, or SBS of the experimental RMGICs. The experimental materials showed higher viscosity and microhardness but similar SBS when compared with the commercial RMGIC.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Dental materials and restorations · Endodontics and Root Canal Treatments · Dental Erosion and Treatment
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Dentistry, Thammasat University, Pathum Thani 12120, Thailand
National Metal and Materials Technology Center (MTEC), National Science and Technology Development Agency, Pathum Thani 12120, Thailand
Assistive Technology and Medical Devices Research Center (A-MED), National Science and Technology Development Agency, Pathum Thani 12120, Thailand
Thammasat University Research Unit in Dental and Bone Substitute Biomaterials, Thammasat University, Pathum Thani 12120, Thailand
Funding
Faculty Of Dentistry, Thammasat University
References (57)
Show source-provided references
1. GBD Oral Disorders Collaborators, Bernabé, E., Marcenes, W., Hernandez, C.R., Bailey, J., Abreu, L.G., Alipour, V., Amini, S., Arabloo, J., and Arefi, Z. (2020). Global, Regional, and National Levels and Trends in Burden of Oral Conditions from 1990 to 2017: A Systematic Analysis for the Global Burden of Disease 2017 Study. J. Dent. Res., 99, 362–373.10.1177/0022034520908533 ↗
2. European Society of Endodontology position statement: Management of deep caries and the exposed pulp10.1111/iej.13080 ↗
3. Contemporary operative caries management: Consensus recommendations on minimally invasive caries removal10.1038/sj.bdj.2017.672 ↗
4. Contemporary concepts in carious tissue removal: A review10.1111/jerd.12338 ↗
5. Effect of Different Liners on Pulpal Outcome after Partial Caries Removal: A Preliminary 12 Months Randomised Controlled Trial10.1159/000499131 ↗
6. Treatment preferences for deep caries lesions among Australian dentists10.1111/adj.12740 ↗
7. Effect of flowable composite liner and glass ionomer liner on class II gingival marginal adaptation of direct composite restorations with different bonding strategies10.1016/j.jdent.2014.02.016 ↗
8. Evaluation of Microhardness of Mineral Trioxide Aggregate After Immediate Placement of Different Coronal Restorations: An In Vitro Study
9. Bond strength and adaptation of pulp capping materials to dentin10.1002/jemt.23440 ↗
10. Outcomes of Partial and Complete Caries Excavation in Permanent Teeth: A 18 Month Clinical Study10.4103/ccd.ccd_344_18 ↗
11. Sidhu, S.K., and Nicholson, J.W. (2016). A Review of Glass-Ionomer Cements for Clinical Dentistry. J. Funct. Biomater., 7.10.3390/jfb7030016 ↗
12. Bonding of a resin-modified glass ionomer cement to dentin using universal adhesives10.5395/rde.2020.45.e36 ↗
13. Influence of 2-hydroxyethyl methacrylate (HEMA) exposure on angiogenic differentiation of dental pulp stem cells (DPSCs)10.1016/j.dental.2020.12.008 ↗
14. Dental resin monomers induce early and potent oxidative damage on human odontoblast-like cells10.1016/j.cbi.2020.109336 ↗
15. Massaro, H., Zambelli, L.F.A., De Britto, A.A., Vieira, R.P., Ligeiro-De-Oliveira, A.P., Andia, D.C., Oliveira, M.T., and Lima, A.F. (2019). Solvent and HEMA Increase Adhesive Toxicity and Cytokine Release from Dental Pulp Cells. Materials, 12.10.3390/ma12172750 ↗
16. The environmental impact of dental amalgam and resin-based composite materials10.1038/sj.bdj.2018.229 ↗
17. Improving flexural strength of resin modified glass-ionomer cement by poly (alkenoic acid) modifications
18. Synthesis and preparation of novel 4-arm star-shape poly(carboxylic acid)s for improved light-cured glass-ionomer cements10.1016/j.dental.2006.02.008 ↗
19. Synthesis and evaluation of HEMA-free glass–ionomer cements for dental applications10.1016/j.dental.2003.07.003 ↗
20. A new approach in self-etching adhesive formulations: Replacing HEMA for surfactant dimethacrylate monomers10.1002/jbm.b.31871 ↗
21. Physical Properties of Glass Ionomer Cement Containing Pre-Reacted Spherical Glass Fillers10.1590/0103-6440202003276 ↗
22. The effect of powder to liquid ratio on physical properties and fluoride release of glass ionomer cements containing pre-reacted spherical glass fillers10.4012/dmj.2019-097 ↗
23. Enhancement effect of pre-reacted glass on strength of glass-ionomer cement10.4012/dmj.2011-136 ↗
24. Boisse, P. (2015). Epoxy/amine reactive systems for composites materials and their thermomechanical properties. Advances in Composites Manufacturing and Process Design, Woodhead Publishing.
25. Mori, T., Takase, K., Yoshida, K., Okazaki, H., and Murata, H. (2021). Influence of monomer type, plasticizer content, and powder/liquid ratio on setting characteristics of acrylic permanent soft denture liners based on poly(ethyl methacrylate/butyl methacrylate) and acetyl tributyl citrate. Dent. Mater. J., 2020–2319.10.4012/dmj.2020-319 ↗
26. Evaluation of shear bond strength between PEEK and resin-based luting material10.1016/j.job.2017.09.003 ↗
27. G*Power 3: A flexible statistical power analysis program for the social, behavioral, and biomedical sciences10.3758/BF03193146 ↗
28. FTIR investigation of monomer polymerisation and polyacid neutralisation kinetics and mechanisms in various aesthetic dental restorative materials10.1016/S0142-9612(03)00599-4 ↗
29. Delgado, A.H.S., and Young, A.M. (2021). Methacrylate peak determination and selection recommendations using ATR-FTIR to investigate polymerisation of dental methacrylate mixtures. PLoS ONE, 16.10.1371/journal.pone.0252999 ↗
30. Cavity Adaptation of Water-Based Restoratives Placed as Liners under a Resin Composite10.1155/2017/5957107 ↗
31. An amino acid-modified and non-HEMA containing glass-ionomer cement10.1016/j.biomaterials.2003.08.033 ↗
32. Dörr, D., Kuhn, U., and Altstädt, V. (2020). Rheological Study of Gelation and Crosslinking in Chemical Modified Polyamide 12 Using a Multiwave Technique. Polymers, 12.10.3390/polym12040855 ↗
33. Chong, B.S., and Chandler, N. (2021). Root Canal Filling Materials and Techniques. Endodontic Materials in Clinical Practice, John Wiley & Sons Ltd.10.1002/9781119513568.ch6 ↗
34. The influence of particle size and fluorine content of aluminosilicate glass on the glass ionomer cement properties10.1016/j.dental.2014.06.003 ↗
35. Contemporary strategies and materials to protect the dental pulp10.12968/denu.2017.44.8.731 ↗
36. Evaluation of mechanical properties and bond strength of nano-hydroxyapatite-silica added glass ionomer cement10.1016/j.ceramint.2018.03.010 ↗
37. Nicholson, J.W., Sidhu, S.K., and Czarnecka, B. (2020). Enhancing the Mechanical Properties of Glass-Ionomer Dental Cements: A Review. Materials, 13.10.3390/ma13112510 ↗
38. Bioactive calcium silicate/poly-ε-caprolactone composite scaffolds 3D printed under mild conditions for bone tissue engineering10.1007/s10856-017-6020-6 ↗
39. Hygroscopic and hydrolytic effects in dental polymer networks10.1016/j.dental.2005.05.005 ↗
40. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer composites10.1016/j.compositesb.2008.01.002 ↗
41. Effect of poly(acrylic acid) architecture on setting and mechanical properties of glass ionomer cements10.1016/j.dental.2020.01.001 ↗
42. Effects of Filler Size on the Mechanical Properties of Polymer-filled Dental Composites: A Review of Recent Developments10.21315/jps2018.29.1.10 ↗
43. Bonding to caries affected dentine10.1016/j.dental.2018.05.017 ↗
44. From Buonocore’s Pioneering Acid-Etch Technique to Self-Adhering Restoratives. A Status Perspective of Rapidly Advancing Dental Adhesive Technology
45. Microtensile Bond Strength of Resin-Modified Glass Ionomer Cement to Sound and Artificial Caries–Affected Root Dentin with Different Conditioning10.2341/16-375-L ↗
46. Shear Bond Strength of Self-Adhesive Flowable Composite, Conventional Flowable Composite and Resin-Modified Glass Ionomer Cement to Primary Dentin
47. Management of caries affected dentin (CAD) with resin modified glass ionomer cement (RMGIC) in the presence of different caries disinfectants and photosensitizers10.1016/j.pdpdt.2020.101978 ↗
48. Zhao, I.S., Mei, M.L., Zhou, Z.L., Burrow, M.F., Lo, E.C.-M., and Chu, C.-H. (2017). Shear Bond Strength and Remineralisation Effect of a Casein Phosphopeptide-Amorphous Calcium Phosphate-Modified Glass Ionomer Cement on Artificial “Caries-Affected” Dentine. Int. J. Mol. Sci., 18.10.3390/ijms18081723 ↗
49. Bond assessment of resin modified glass ionomer cement to dentin conditioned with photosensitizers, laser and conventional regimes10.1016/j.pdpdt.2020.101795 ↗
50. Assessment of Bonding Effectiveness of Adhesive Materials to Tooth Structure using Bond Strength Test Methods: A Review of Literature10.2174/1745017901814010664 ↗
51. Validity of bond strength tests: A critical review: Part I10.4103/0972-0707.136340 ↗
52. Effect of dentin contamination with two hemostatic agents on bond strength of resin-modified glass ionomer cement with different conditioning10.4012/dmj.2018-059 ↗
53. Effect of Conditioning and Aging on the Bond Strength and Interfacial Morphology of Glass-ionomer Cement Bonded to Dentin
54. Development of self-adhesive pulp-capping agents containing a novel hydrophilic and highly polymerizable acrylamide monomer10.1039/D0TB00079E ↗
55. Kim, Y.K., Hong, M.-H., and Kwon, T.-Y. (2020). Dentin Bonding of TheraCal LC Calcium Silicate Containing an Acidic Monomer: An In Vitro Study. Materials, 13.10.3390/ma13020293 ↗
56. The role of polymerization in adhesive dentistry10.1016/j.dental.2018.11.012 ↗
57. Conversion, shrinkage, water sorption, flexural strength and modulus of re-mineralizing dental composites10.1016/j.dental.2015.08.149 ↗