Flexural Strength and Hardness Analysis of 3D-Printed vs. Milled Resin Composites Indicated for Definitive Crowns
Source abstract
Abstract
The growing use of 3D-printed dental restorations has created a need to understand how the mechanical behaviour of definitive 3D-printed resin composites compares with milled counterparts. This study compared the mechanical properties of 3D-printed and milled definitive crowns and examined the factors affecting these properties. The 3D-printed materials (Permanent Crown Resin: PCR, VarseoSmile Crown Plus: VCP, and Crowntec: CT) and milled blocks (Brilliant Crios: BC, Shofu Block HC: HC, and Grandio Blocs: Gr) were tested. Filler content was evaluated using the ash method (n = 3), and flexural strength (FS) and flexural modulus (Ef) were assessed using a three-point bending test (n = 10). Martens hardness (HM), indentation modulus, and Vickers hardness were determined using the Martens indentation test (n = 24). Vickers hardness was also measured with the Vickers indenter tester (n = 24). Statistical analysis investigated differences between materials and methods, and correlations between filler weight and mechanical properties (α = 0.05). FS of milled blocks, Gr (244.5 MPa), BC (225.5 MPa), and HC (155 MPa), were higher than that of the 3D-printed resin composites: PCR (143.6 MPa), CT (140.9 MPa), and VCP (128 MPa). Measured mechanical properties of the milled blocks were significantly higher than those of the 3D-printed materials (p < 0.001). HM of the 3D-printed materials was similar (≈217 N/mm2), while HM of the milled blocks ranged from 434.7 to 858.4 N/mm2. The 3D-printed materials showed comparable properties; however, milled blocks differed significantly (p < 0.05). Filler content was strongly associated with FS and HM. Within the limitations of this study, the milled resin composites showed markedly higher strength and hardness, while 3D-printed materials may be suitable for low-to-moderate load clinical scenarios. Further studies to evaluate the long-term performance of the 3D-printed resin composites are recommended.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Dental materials and restorations · Dental Health and Care Utilization · Dental Implant Techniques and Outcomes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Oral and Maxillofacial Prosthodontics Department, Faculty of Dentistry, King Abdulaziz University, Jeddah 21589, Saudi Arabia
Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester M13 9PL, UK
Funding
KAU Endowment
References (37)
Show source-provided references
1. Digital dentistry: An overview of recent developments for CAD/CAM generated restorations10.1038/sj.bdj.2008.350 ↗
2. CAD/CAM systems available for the fabrication of crown and bridge restorations10.1111/j.1834-7819.2010.01300.x ↗
3. 3D printing/additive manufacturing single titanium dental implants: A prospective multicenter study with 3 years of follow-up10.1155/2016/8590971 ↗
4. Rosenstiel, S.F., and Land, M.F. (2015). Part II: Clinical procedures. Contemporary Fixed Prosthodontics, Elsevier Health Sciences. [5th ed.].
5. All-ceramic or metal-ceramic tooth-supported fixed dental prostheses (FDPs)? A systematic review of the survival and complication rates
6. A review of dental CAD/CAM: Current status and future perspectives from 20 years of experience10.4012/dmj.28.44 ↗
7. 3D printing in dentistry10.1038/sj.bdj.2015.914 ↗
8. Effects of build direction on the mechanical properties of 3D-printed complete coverage interim dental restorations10.1016/j.prosdent.2015.12.002 ↗
9. Basu, A. (2015). Silk as a reinforcement in polymer matrix composites. Advances in Silk Science and Technology, Woodhead Publishing. [1st ed.].
10. Sakaguchi, R.L., and Powers, J.M. (2012). Restorative materials—Composites and polymers. Craig’s Restorative Dental Materials, Elsevier Health Sciences. [13th ed.].
11. Hardness measured with traditional vickers and martens hardness methods10.1016/j.dental.2006.10.001 ↗
12. The effect of zirconia sintering temperature on flexural strength, grain size, and contrast ratio10.1007/s00784-012-0692-6 ↗
13. Effects of print orientation and artificial aging on the flexural strength and flexural modulus of 3D printed restorative resin materials10.1016/j.prosdent.2024.08.008 ↗
14. Effects of printing orientation and artificial ageing on martens hardness and indentation modulus of 3D printed restorative resin materials10.1016/j.dental.2024.05.005 ↗
15. (1996). Textile-Glass-Reinforced Plastics—Prepregs, Moulding Compounds and laminates—Determination of the Textile-Glass and Mineral-Filler Content—Calcination Methods (Standard No. ISO 1172:1996).
16. (2019). Dentistry—Polymer-Based Restorative Materials (Standard No. BS EN ISO 4049:2019).
17. (2016). Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters—Part 4: Test Method for Metallic and Non-Metallic Coatings (Standard No. BS EN ISO 14577-4:2016).
18. (2023). Metallic Materials—Vickers Hardness Test—Part 1: Test Method (Standard No. ISO 6507-1:2023).
19. Effect of the composition of CAD/CAM composite blocks on mechanical properties10.1155/2018/4893143 ↗
20. Contributions on the study of the compressive strength of the light-cured composite resins
21. Dimensional change measurements of conventional and flowable composite resins using a laser displacement sensor10.4012/dmj.28.544 ↗
22. Grzebieluch, W., Kowalewski, P., Grygier, D., Rutkowska-Gorczyca, M., Kozakiewicz, M., and Jurczyszyn, K. (2021). Printable and machinable dental restorative composites for CAD/CAM application—Comparison of mechanical properties, fractographic, texture and fractal dimension analysis. Materials, 14.10.3390/ma14174919 ↗
23. Investigating filler morphology and mechanical properties of new low-shrinkage resin composite types10.1111/j.1365-2842.2010.02066.x ↗
24. Filler characteristics of modern dental resin composites and their influence on physico-mechanical properties10.1016/j.dental.2016.09.034 ↗
25. Influence of filler characteristics on the performance of dental composites: A comprehensive review10.1016/j.ceramint.2022.06.314 ↗
26. Resin composite materials for chairside CAD/CAM restorations: A comparison of selected mechanical properties10.1155/2021/8828954 ↗
27. Influence of accelerated ageing on the physical properties of CAD/CAM restorative materials10.1007/s00784-019-03101-w ↗
28. Conversion, shrinkage, water sorption, flexural strength and modulus of re-mineralizing dental composites10.1016/j.dental.2015.08.149 ↗
29. Jain, S., Sayed, M.E., Shetty, M., Alqahtani, S.M., Al Wadei, M.H.D., Gupta, S.G., Othman, A.A.A., Alshehri, A.H., Alqarni, H., and Mobarki, A.H. (2022). Physical and mechanical properties of 3D-printed provisional crowns and fixed dental prosthesis resins compared to CAD/CAM milled and conventional provisional resins: A systematic review and meta-analysis. Polymers, 14.10.3390/polym14132691 ↗
30. Comparative evaluation of the effect of thermocycling on the mechanical properties of conventionally polymerized, CAD-CAM milled, and 3D-printed interim materials
31. Temizci, T., and Bozoğulları, H.N. (2024). Effect of thermocycling on the mechanical properties of permanent composite-based CAD-CAM restorative materials produced by additive and subtractive manufacturing techniques. BMC Oral Health, 24.10.1186/s12903-024-04016-z ↗
32. Effect of hydrothermal aging on the microhardness of high-and low-viscosity conventional and additively manufactured polymers
33. Academy of dental materials guidance—Resin composites: Part I—Mechanical properties10.1016/j.dental.2017.04.013 ↗
34. Flexural strength and modulus of elasticity of different types of resin-based composites10.1590/S1806-83242007000100003 ↗
35. Schiavi, A., Origlia, C., Germak, A., Prato, A., and Genta, G. (2021). Indentation modulus, indentation work and creep of metals and alloys at the macro-scale level: Experimental insights into the use of a primary vickers hardness standard machine. Materials, 14.10.3390/ma14112912 ↗
36. 3D-printed anisotropic polymer materials for functional applications10.1002/adma.202102877 ↗
37. Additive manufacturing technologies used for processing polymers: Current status and potential application in prosthetic dentistry10.1111/jopr.12801 ↗