journal article·2024-10-05Open access

3D-Printable Gelatin Methacrylate-Xanthan Gum Hydrogel Bioink Enabling Human Induced Pluripotent Stem Cell Differentiation into Cardiomyocytes

Virginia Deidda, Isabel Ventisette, Marianna Langione, Lucrezia Giammarino, Josè Manuel Pioner, Caterina Credi, Federico Carpi

Journal of Functional Biomaterials· Volume 15· Issue 10

Abstract

We describe the development of a bioink to bioprint human induced pluripotent stem cells (hiPSCs) for possible cardiac tissue engineering using a gelatin methacrylate (GelMA)-based hydrogel. While previous studies have shown that GelMA at a low concentration (5% w/v) allows for the growth of diverse cells, its 3D printability has been found to be limited by its low viscosity. To overcome that drawback, making the hydrogel both compatible with hiPSCs and 3D-printable, we developed an extrudable GelMA-based bioink by adding xanthan gum (XG). The GelMA-XG composite hydrogel had an elastic modulus (~9 kPa) comparable to that of cardiac tissue, and enabled 3D printing with high values of printing accuracy (83%) and printability (0.98). Tests with hiPSCs showed the hydrogel’s ability to promote their proliferation within both 2D and 3D cell cultures. The tests also showed that hiPSCs inside hemispheres of the hydrogel were able to differentiate into cardiomyocytes, capable of spontaneous contractions (average frequency of ~0.5 Hz and amplitude of ~2%). Furthermore, bioprinting tests proved the possibility of fabricating 3D constructs of the hiPSC-laden hydrogel, with well-defined line widths (~800 μm).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: 3D Printing in Biomedical Research · Neuroscience and Neural Engineering · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Industrial Engineering, University of Florence, 50139 Florence, Italy

Department of Experimental and Clinical Medicine, University of Florence, 50134 Florence, Italy

Department of Neurosciences, Psychology, Drug Research and Child Health, University of Florence, 50139 Florence, Italy

Department of Biology, University of Florence, 50019 Sesto Fiorentino, Italy

European Laboratory for Non-Linear Spectroscopy, University of Florence, 50019 Sesto Fiorentino, Italy

National Institute of Optics, National Research Council, 50019 Sesto Fiorentino, Italy

Funding

Italian Ministry of University and Research · Italian Ministry of Health · Fondazione Cassa di Risparmio di Firenze, Italy

References (43)

Show source-provided references
1. Microfabricated biomaterials for engineering 3D tissues10.1002/adma.201104631 ↗
2. In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid10.1161/CIRCRESAHA.119.316155 ↗
3. A tissue-engineered scale model of the heart ventricle10.1038/s41551-018-0271-5 ↗
4. Jain, T., Baker, H.B., Gipsov, A., Fisher, J.P., Joy, A., Kaplan, D.S., and Isayeva, I. (2021). Impact of cell density on the bioprinting of gelatin methacrylate (GelMA) bioinks. Bioprinting, 22.10.1016/j.bprint.2021.e00131 ↗
5. Bio-ink materials for 3D bio-printing
6. Macroporous hydrogel scaffolds for three-dimensional cell culture and tissue engineering10.1089/ten.teb.2016.0465 ↗
7. Iervolino, F., Belgio, B., Bonessa, A., Potere, F., Suriano, R., Boschetti, F., Mantero, S., and Levi, M. (2023). Versatile and non-cytotoxic GelMA-xanthan gum biomaterial ink for extrusion-based 3D bioprinting. Bioprinting, 31.10.1016/j.bprint.2023.e00269 ↗
8. Gao, Q., Kim, B.S., and Gao, G. (2021). Advanced strategies for 3D bioprinting of tissue and organ analogs using alginate hydrogel bioinks. Mar. Drugs, 19.10.3390/md19120708 ↗
9. Fatimi, A., Okoro, O.V., Podstawczyk, D., Siminska-Stanny, J., and Shavandi, A. (2022). Natural Hydrogel-Based Bio-Inks for 3D Bioprinting in Tissue Engineering: A Review. Gels, 8.10.3390/gels8030179 ↗
10. Extrusion bioprinting of shear-thinning gelatin methacryloyl bioinks10.1002/adhm.201601451 ↗
11. Bioprinting vessel-like constructs using hyaluronan hydrogels crosslinked with tetrahedral polyethylene glycol tetracrylates10.1016/j.biomaterials.2010.04.045 ↗
12. Schöneberg, J., De Lorenzi, F., Theek, B., Blaeser, A., Rommel, D., Kuehne, A.J.C., Kießling, F., and Fischer, H. (2018). Engineering biofunctional in vitro vessel models using a multilayer bioprinting technique. Sci. Rep., 8.10.1038/s41598-018-28715-0 ↗
13. Leucht, A., Volz, A.C., Rogal, J., Borchers, K., and Kluger, P.J. (2020). Advanced gelatin-based vascularization bioinks for extrusion-based bioprinting of vascularized bone equivalents. Sci. Rep., 10.10.1038/s41598-020-62166-w ↗
14. Extrusion-based 3D bioprinting of alginate-based tissue constructs10.1016/j.procir.2020.06.007 ↗
15. 3D printing of highly stretchable and tough hydrogels into complex, Cellularized structures10.1002/adma.201501099 ↗
16. Fu, Z., Angeline, V., and Sun, W. (2021). Evaluation of printing parameters on 3D extrusion printing of pluronic hydrogels and machine learning guided parameter recommendation. Int. J. Bioprint., 7.10.18063/ijb.v7i4.434 ↗
17. Comparison of photo cross linkable gelatin derivatives and initiators for three-dimensional extrusion bioprinting10.1021/acs.biomac.9b01204 ↗
18. Cell-laden microengineered gelatin methacrylate hydrogels10.1016/j.biomaterials.2010.03.064 ↗
19. Lessone, S. (2017). Processi di Fotopolimerizzazione per L’ottenimento di un Nanocomposito a Base Cellulosica. [Ph.D. Thesis, Politecnico di Torino].
20. Functional human vascular network generated in photocrosslinkable gelatin methacrylate hydrogels10.1002/adfm.201101662 ↗
21. Investigating the repair of alveolar bone defects by gelatin methacrylate hydrogels-encapsulated human periodontal ligament stem cells10.1007/s10856-019-6333-8 ↗
22. The stiffness of living tissues and its implications for tissue engineering10.1038/s41578-019-0169-1 ↗
23. Cardiac MR elastography for quantitative assessment of elevated myocardial stiffness in cardiac amyloidosis10.1002/jmri.25678 ↗
24. Bertassoni, L.E., Cardoso, J.C., Manoharan, V., Cristino, A.L., Bhise, N.S., Araujo, W.A., Zorlutuna, P., Vrana, N.E., Ghaemmaghami, A.M., and Dokmeci, M.R. (2014). Direct-write bioprinting of cell-laden methacrylated gelatin hydrogels. Biofabrication, 6.10.1088/1758-5082/6/2/024105 ↗
25. Gelatin methacrylate scaffold for bone tissue engineering: The influence of polymer concentration10.1002/jbm.a.36226 ↗
26. Pepelanova, I., Kruppa, K., Scheper, T., and Lavrentieva, A. (2018). Gelatin-methacryloyl (GelMA) hydrogels with defined degree of functionalization as a versatile toolkit for 3D cell culture and extrusion bioprinting. Bioengineering, 5.10.3390/bioengineering5030055 ↗
27. Shie, M.Y., Lee, J.J., Ho, C.C., Yen, S.Y., Ng, H.Y., and Chen, Y.W. (2020). Effects of gelatin methacrylate bio-ink concentration on mechano-physical properties and human dermal fibroblast behavior. Polymers, 12.10.3390/polym12091930 ↗
28. 3D bioprinting of low-concentration cell-laden gelatin methacrylate (GelMA) bioinks with a two-step cross-linking strategy10.1021/acsami.7b16059 ↗
29. Stiffness of photocrosslinkable gelatin hydrogel influences nucleus pulposus cell propertiesin vitro10.1111/jcmm.16141 ↗
30. Wei, K., Sun, J., Gao, Q., Yang, X., Ye, Y., Ji, J., and Sun, X. (2021). 3D “honeycomb” cell/carbon nanofiber/gelatin methacryloyl (GelMA) modified screen-printed electrode for electrochemical assessment of the combined toxicity of deoxynivalenol family mycotoxins. Bioelectrochemistry, 139.10.1016/j.bioelechem.2021.107743 ↗
31. Li, J., Moeinzadeh, S., Kim, C., Pan, C.C., Weale, G., Kim, S., Abrams, G., James, A.W., Choo, H., and Chan, C. (2023). Development and systematic characterization of GelMA/alginate/PEGDMA/xanthan gum hydrogel bioink system for extrusion bioprinting. Biomaterials, 293.10.1016/j.biomaterials.2022.121969 ↗
32. Biomaterial composition and stiffness as decisive properties of 3D bioprinted constructs for type II collagen stimulation10.1016/j.actbio.2022.08.058 ↗
33. Mechanical behaviour of alginate-gelatin hydrogels for 3D bioprinting10.1016/j.jmbbm.2017.12.018 ↗
34. Ouyang, L., Yao, R., Zhao, Y., and Sun, W. (2016). Effect of bioink properties on printability and cell viability for 3D bioplotting of embryonic stem cells. Biofabrication, 8.10.1088/1758-5090/8/3/035020 ↗
35. Direct 3D bioprinting of prevascularized tissue constructs with complex microarchitecture10.1016/j.biomaterials.2017.01.042 ↗
36. Semba, J.A., Mieloch, A.A., Tomaszewska, E., Cywoniuk, P., and Rybka, J.D. (2022). Formulation and evaluation of a bioink composed of alginate, gelatin, and nanocellulose for meniscal tissue engineering. Int. J. Bioprint., 9.10.18063/ijb.v9i1.621 ↗
37. Acquisition of a quantitative, stoichiometrically conserved ratiometric marker of maturation status in stem cell-derived cardiac myocytes10.1016/j.stemcr.2014.07.012 ↗
38. Slower calcium handling balances faster cross-bridge cycling in human MYBPC3 HCM10.1161/CIRCRESAHA.122.321956 ↗
39. Doss, M.X., Di Diego, J.M., Goodrow, R.J., Wu, Y., Cordeiro, J.M., Nesterenko, V.V., Barajas-Martínez, H., Hu, D., Urrutia, J., and Desai, M. (2012). Maximum diastolic potential of human induced pluripotent stem cell-derived cardiomyocytes depends critically on IKr. PLoS ONE, 7.10.1371/journal.pone.0040288 ↗
40. Pioner, J.M., Santini, L., Palandri, C., Martella, D., Lupi, F., Langione, M., Querceto, S., Grandinetti, B., Balducci, V., and Benzoni, P. (2019). Optical investigation of action potential and calcium handling maturation of hiPSC-cardiomyocytes on biomimetic substrates. Int. J. Mol. Sci., 20.10.3390/ijms20153799 ↗
41. Late sodium current inhibition reverses electromechanical dysfunction in human hypertrophic cardiomyopathy10.1161/CIRCULATIONAHA.112.134932 ↗
42. The immature electrophysiological phenotype of iPSC-CMs still hampers in vitro drug screening: Special focus on IK110.1016/j.pharmthera.2017.10.001 ↗
43. Biophysical, molecular, and pharmacological characterization of voltage-dependent sodium channels from induced pluripotent stem cell-derived cardiomyocytes10.1016/j.cjca.2016.10.001 ↗