journal article·2024-10-01Open access

The Effect of Erosive Media on the Mechanical Properties of CAD/CAM Composite Materials

Marwa M. Alnsour, Rasha A. Alamoush, Nikolaos Silikas, Julian D. Satterthwaite

Journal of Functional Biomaterials· Volume 15· Issue 10

Abstract

This study aimed to investigate the effect of acidic media storage (gastric acid and Coca-Cola) on the mechanical properties of CAD/CAM materials. Three types of materials were tested: a polymer-infiltrated ceramic network (PICN) (Vita Enamic (En), VITA Zahnfabrik, Germany), a resin composite block (RCB) (Cerasmart (Cs), GC Corp, Japan), and a conventional resin-based composite (Gradia direct (Gr), GC Corp, Japan), which was used as a control. Beam-shaped specimens of each material, with dimensions of 16 mm × 4 mm × 1.5 mm, were prepared (90 in total). The specimens were divided into subgroups (10 each) and stored for 96 h in either gastric acid, Coca-Cola, or distilled water. Flexural strength and elastic modulus were evaluated using a three-point flexural strength test with acoustic emission (AE) monitoring. Vickers microhardness was measured before and after storage in gastric acid and Coca-Cola. Data were statistically analysed using two-way and one-way ANOVA, the Tukey’s post hoc, and independent t-test at a significance level of 0.05. The results showed that Cs and En maintained their flexural strength and elastic modulus after acidic media exposure, while Gr experienced a significant decrease in flexural strength following gastric acid storage (p < 0.01). Initial crack detection was not possible using the AE system, impacting the determination of flexural strength. Exposure to acidic media decreased all materials’ microhardness, with Gr showing the most notable reduction (p < 0.0001). Gastric acid had a greater impact on the microhardness of all tested materials compared to Coca-Cola (p < 0.0001). In conclusion, storage in erosive media did not notably affect the flexural strength or elastic modulus of CAD/CAM composites but it did affect hardness. CAD/CAM composite blocks demonstrated superior mechanical properties compared to the conventional composite.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Orthopaedic implants and arthroplasty · Endodontics and Root Canal Treatments

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Restorative Dentistry, School of Dentistry, University of Jordan, Amman 11942, Jordan

Dental Department, Jordan University Hospital, Amman 13046, Jordan

Department of Fixed and Removable Prosthodontics, School of Dentistry, University of Jordan, Amman 11942, Jordan

Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester M13 9PL, UK

References (35)

Show source-provided references
1. Current concepts on the management of tooth wear: Part 1. Assessment, treatment planning, and strategies for the prevention and the passive management of tooth wear10.1038/sj.bdj.2011.1099 ↗
2. Tooth wear guidelines for the BSRD part 1: Aetiology, diagnosis, and prevention10.12968/denu.2018.45.6.483 ↗
3. Tooth wear and erosion: Methodological issues in epidemiological and public health research and the future research agenda
4. Tooth wear guidelines for the BSRD part 2: Fixed management of tooth wear10.12968/denu.2018.45.7.590 ↗
5. Current concepts on the management of tooth wear: Part 4. An overview of the restorative techniques and dental materials commonly applied for the management of tooth wear10.1038/sj.bdj.2012.137 ↗
6. Dental biomaterials for chairside CAD/CAM: State of the art10.4047/jap.2017.9.6.486 ↗
7. Alamoush, R.A., Salim, N.A., Elraggal, A., Satterthwaite, J.D., and Silikas, N. (2023). The effect of water storage on nanoindentation creep of various CAD-CAM composite blocks. BMC Oral Health, 23.10.1186/s12903-023-03145-1 ↗
8. High-temperature-pressure polymerized resin-infiltrated ceramic networks10.1177/0022034513511972 ↗
9. Scribante, A., Bollardi, M., Chiesa, M., Poggio, C., and Colombo, M. (2019). Flexural properties and elastic modulus of various esthetic restorative materials: Assessment following exposure to acidic beverages. Biomed Res. Int., 2019.10.1155/2019/5109481 ↗
10. Degradation of computer-aided design/computer-aided manufacturing composites by dietary solvents: An optical three-dimensional surface analysis10.2341/19-070-L ↗
11. Does artificial aging affect mechanical properties of CAD/CAM composite materials?10.1016/j.jpor.2017.06.001 ↗
12. Effects of simulated gastric juice on CAD/CAM resin composites—Morphological and mechanical evaluations10.1111/jopr.12420 ↗
13. Influence of simulated gastric juice on surface characteristics of CAD/CAM monolithic materials10.1016/j.prosdent.2019.04.018 ↗
14. Colombo, M., Poggio, C., Lasagna, A., Chiesa, M., and Scribante, A. (2019). Vickers micro-hardness of new restorative CAD/CAM dental materials: Evaluation and comparison after exposure to acidic drink. Materials, 12.10.3390/ma12081246 ↗
15. Effect of acidic solutions on the surface roughness and microhardness of indirect restorative materials: A systematic review and meta-analysis
16. Schmohl, L., Roesner, A.J., Fuchs, F., Wagner, M., Schmidt, M.B., Hahnel, S., Rauch, A., and Koenig, A. (2022). Acid resistance of CAD/CAM resin composites: Insights from in vitro analysis. Biomedicines, 10.10.3390/biomedicines10061383 ↗
17. Effect of acidic media on flexural strength and fatigue of CAD-CAM dental materials10.1016/j.dental.2022.11.019 ↗
18. Long-term effects of simulated gastric juice alternated with brushing on hardness, substance loss, flexural strength and reliability of CAD-CAM monolithic materials10.1590/1678-7757-2021-0536 ↗
19. Effect of different beverages on the color stability and microhardness of CAD/CAM hybrid versus feldspathic ceramic blocks: An in-vitro study10.1016/j.fdj.2017.07.001 ↗
20. Chemical degradation of dental CAD/CAM materials
21. ADM guidance-ceramics: Fatigue principles and testing10.1016/j.dental.2017.09.006 ↗
22. Fracture of fiber-reinforced composites analyzed via acoustic emission10.4012/dmj.2014-325 ↗
23. (2018). Dentistry—Ceramic Materials (Standard No. EN ISO 6872:2015/A1:2018).
24. Mechanical properties of resin-ceramic CAD/CAM restorative materials10.1016/j.prosdent.2015.04.016 ↗
25. Uniaxial/biaxial flexure strengths and elastic properties of resin-composite block materials for CAD/CAM10.1016/j.dental.2018.11.032 ↗
26. Mechanical properties of direct composite resins and CAD/CAM composite blocks10.3390/oral4020017 ↗
27. Nanofilled resin composite properties and clinical performance: A review10.2341/17-208-T ↗
28. Pereira, F. (2019). Update on the New Polymer Infiltrated Ceramic Network Material (PICN). [Master’s Thesis, University of Porto].
29. The elastic moduli of enamel and dentine10.1016/0267-6605(93)90045-9 ↗
30. Wear, strength, modulus and hardness of CAD/CAM restorative materials10.1016/j.dental.2016.08.222 ↗
31. Alamoush, R.A., Silikas, N., Salim, N.A., Al-Nasrawi, S., and Satterthwaite, J.D. (2018). Effect of the composition of CAD/CAM composite blocks on mechanical properties. BioMed Res. Int., 2018.10.1155/2018/4893143 ↗
32. Microhardness evaluation of microhybrid versus nanofilled resin composite after exposure to acidic drinks10.4103/jispcd.JISPCD_66_22 ↗
33. Microhardness of different esthetic restorative materials: Evaluation and comparison after exposure to acidic drink10.4103/1735-3327.231863 ↗
34. Elraggal, A., Afifi, R., and Abdelraheem, I. (2022). Effect of erosive media on microhardness and fracture toughness of CAD-CAM dental materials. BMC Oral Health, 22.10.1186/s12903-022-02230-1 ↗
35. Effects of commonly consumed beverages on surface roughness and color stability of the nano, microhybrid and hybrid composite resins: An in vitro study10.5005/jp-journals-10024-1390 ↗