journal article·2023-01-28Open access

The Effect of Polishing, Glazing, and Aging on Optical Characteristics of Multi-Layered Dental Zirconia with Different Degrees of Translucency

Flavia Roxana Toma, Sorin Daniel Porojan, Roxana Diana Vasiliu, Liliana Porojan

Abstract

(1) Background: Considering that the appearance of a dental material is an important factor that contributes to the success of prosthetic restorations. The purpose of this study is to investigate the optical properties and color changes among the layers of three commercial zirconias, to compare the aspect of the polished and glazed surfaces before and after aging and to evaluate the effects of hydrothermal degradation on their aesthetics. (2) Methods: Forty-eight plate-shaped samples were sectioned from presintered blocks of each multilayer translucent zirconia with different Yttrium content: Ceramill Zolid fx ML (5 mol%) = CeZ, STML (4 mol%) = STM, IPS e.maxZirCAD CEREC/in Lab MT Multi (4 mol% + 5 mol%) = IPZ. The samples were sintered according to the recommendation of each manufacturer, and half (24) of them were polished and the other half (24) glazed on one of the surfaces. Each type was equally divided into one control and one aging group, and, for each material, this resulted in four groups (n = 12): polished-control, polished-autoclaved glazed-control, and glazed-autoclaved. The artificial aging was carried out with an autoclave and distilled water at 134 °C, 0.2 MPa for 1 h, and for optical parameters (TP, CR, OP) and color change (ΔE*) measurements on a black and white background in a CIE L*a*b* color system, a spectrophotometer was used. The specimens were evaluated in incisal, cervical, and medium areas on polished and glazed samples before and after the aging stage. Statistical analysis was achieved with a two-way ANOVA test, the unpaired t-test, and the paired t-test. (3) Results: Before and after aging, the mean TP values for polished samples were higher than the glazed ones. After aging, the mean TP values increased for all groups (except polished CeZ), and significant differences were reported for polished STM, IPZ. After LTD, the opalescence registered an increase for almost all groups (except polished CeZ, polished and glazed IPZ—medium area), and significant differences were reported for almost all groups (except STM—incisal, IPZ—cervical, medium areas). The levels of color change were between extremely slight to perceivable. (4) Conclusions: Optical properties of the selected multilayer zirconia were influenced by polishing and glazing as surface treatment and affected by artificial aging (CeZ the least); perceivable color changes for polished STM, IPZ were detected.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Dental Erosion and Treatment · Dental Implant Techniques and Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Dental Prostheses Technology (Dental Technology), Center for Advanced Technologies in Dental Prosthodontics, Faculty of Dental Medicine, “Victor Babeș” University of Medicine and Pharmacy Timișoara, Eftimie Murgu Sq. No. 2, 300041 Timisoara, Romania

Department of Oral Rehabilitation (Dental Technology), Center for Advanced Technologies in Dental Prosthodontics, Faculty of Dental Medicine, “Victor Babeș” University of Medicine and Pharmacy Timișoara, Eftimie Murgu Sq. No. 2, 300041 Timisoara, Romania

References (54)

Show source-provided references
1. Salmang, H., and Scholze, H. (2007). Keramik Vollständing Neuarbeitete und Erweiterte Auflage, Springer.
2. Holleman-Wiberg, E. (1995). Lehrbuch der Anorganischen Chemie, Walterde Gruyter & Co.. [101st ed.].
3. An overview of monolithic zirconia in dentistry10.1080/13102818.2016.1177470 ↗
4. Color Stainability of CAD/CAM and Nanocomposite Resin Materials10.1016/j.prosdent.2015.06.014 ↗
5. Novel zirconia materials in dentistry10.1177/0022034517737483 ↗
6. Scientific Documentation (2022, March 03). Microsoft Word–WissDok IPS e.max ZirCADenglisch aktualisiert 30112017.docx. Available online: https://www.ivoclar.com/.
7. Making Yttria-stabilized tetragonal zirconia translucent10.1016/j.dental.2014.08.375 ↗
8. Crystallographic and morphological analysis of sandblasted highly translucent dental zirconia10.1016/j.dental.2017.12.008 ↗
9. Translucent radiosity: Efficiently combining diffuse inter-reflection and subsurface scattering10.1109/TVCG.2013.256 ↗
10. Optical properties and light irradiance of monolithic zirconia at variable thicknesses10.1016/j.dental.2015.06.016 ↗
11. Evaluation of the Effect of Surface Polishing, Oral Beverages and Food Colorants on Color Stability and Surface Roughness of Nanocomposite Resins
12. Mechanical reliability, fatigue strength and survival analysis of new polycrystalline translucent zirconia ceramics for monolithic restorations10.1016/j.jmbbm.2018.05.029 ↗
13. Light transmittance by a multi-coloured zirconia material10.4012/dmj.2014-238 ↗
14. New multi-layered zirconia: Composition, microstructure and translucency10.1016/j.dental.2019.02.017 ↗
15. Effect of zirconia pigmentation on translucency
16. Critical influence of alumina content on the low temperature degradation of 2–3 mol% yttria-stabilized TZP for dental restorations10.1016/j.jeurceramsoc.2014.09.018 ↗
17. Effect of dopants and sintering temperature on microstructure and low temperature degradation of dental Y-TZP zirconia10.1016/j.jeurceramsoc.2012.07.032 ↗
18. Effect of Fe2O3 doping on colour and mechanical properties of Y-TZP ceramics10.1016/j.ceramint.2018.06.273 ↗
19. Densification of zirconia—Conventional methods10.4028/www.scientific.net/KEM.153-154.251 ↗
20. Determination of hafnium in zirconium metal and zircaloy 4 metal standard reference materials by isotope dilution spark source mass spectrometry10.1021/ac00267a017 ↗
21. Effect of different finishing techniques for restaurative materials on surface roughness and bacterial adhesion10.1016/S0022-3913(10)60034-0 ↗
22. Influence of low-temperature environmental exposure on the mechanical properties and structural stability of dental zirconia10.1111/j.1532-849X.2011.00838.x ↗
23. Anusavice, K.J., Shen, C., and Rawls, H.R. (2012). Phillip’s Science of Dental Materials, Elsevier. [12th ed.].
24. The effect of porcelain polishing systems on the color and surface texture of feldspathic porcelain10.1016/j.prosdent.2006.05.009 ↗
25. Low-temperature degradation of different zirconia ceramics for dental application10.1016/j.actbio.2011.11.016 ↗
26. Effect of various polishing system on the surface roughness and phase transformation of zirconia and the durability of the polishing systems10.1016/j.prosdent.2016.10.005 ↗
27. Surface roughness and the flexural and bend strength of zirconia after different surface treatments10.1016/j.prosdent.2016.02.018 ↗
28. Low-temperature degradation of a Y-TPZ ceramic after surface treatments10.1002/jbm.b.32957 ↗
29. Low-temperature degradation of Y-TZP ceramics: A systematic review and meta-analysis10.1016/j.jmbbm.2015.10.017 ↗
30. A critical comparison of methods for the determination of aging sensitivity in biomedical grade yttria-stabilized zirconia10.1002/jbm.b.30123 ↗
31. Stabilized zirconia as a structural ceramic: An overview10.1016/j.dental.2007.05.005 ↗
32. Mechanical and microstructural properties of ultra-translucent zirconia ceramic stabilized with 5 mol % yttria10.1016/j.jmbbm.2020.103974 ↗
33. (2022, February 18). Ivoclar-Vivadent IPS e.max ZirCAD Labside Gebrauchsinformation 2019-06-27, Rev3a. Available online: https://www.cadstar.dental/download/87/materialdokumentation-de/5667919/ipse-maxzircadlabside.pdf.
34. (2022, February 21). Kuraray Noritake—Technical Guide Katana Zirconia Multi-Layered Series. 201805-brochure-katana-zirconia-technical-guide-web-en_2.pdf. Available online: https://www.kuraraynoritake.eu/.
35. Amann Girrbach-Verarbaitungstehnik—Zolid DNA Generation (2022, January 25). 976109DE, 03/2021. Indikationsleitfaden_Zirkon_DE.pdf. Available online: https://www.Amanngirrbach.com.
36. Low-temperature aging of Y-TZP ceramics10.1111/j.1151-2916.1999.tb02055.x ↗
37. Validation of two clinical color measuring instruments for use in dental research10.1016/j.jdent.2022.104223 ↗
38. CIE (2004). Colorimetry, Commission Internationale de l′Eclairage. CIE 15:2004.
39. Optical and Mechanical Properties of Newly Developed Multilayer Zirconia10.1111/jopr.12730 ↗
40. Paravina, R., and Powers, J. (2004). Esthetic Color Training in Dentistry, Mosby.
41. Ultra-translucent zirconia processing and aging effect on microstructural, optical, and mechanical properties10.1016/j.dental.2022.02.016 ↗
42. Effect of polishing and glazing on the color and spectral distribution of monolithic zirconia10.4047/jap.2013.5.3.296 ↗
43. Toma, F.R., Birdeanu, M.I., Utu, I.D., Vasiliu, R.D., Moleriu, L.C., and Porojan, L. (2022). Surface characteristics of high translucent zirconia related to aging. Materials, 15.10.3390/ma15103606 ↗
44. Influence of coloring procedure on flexural resistance of zirconia blocks10.1016/j.prosdent.2015.02.001 ↗
45. Comparison of translucency for different thickness of recent types of esthetic zirconia ceramics versus conventional ceramics… (in vitro study)10.1016/j.fdj.2018.05.003 ↗
46. Translucency of human teeth and dental restorative materials and its clinical relevance10.1117/1.JBO.20.4.045002 ↗
47. Translucency of dental ceramics with different thicknesses10.1016/S0022-3913(13)60333-9 ↗
48. Human perception of dental porcelain translucency correlated to spectrophotometric measurements10.1111/j.1532-849X.2009.00542.x ↗
49. Effect of sintering process on color parameters of nano-sized yttria partially stabilized tetragonal monolithic zirconia
50. Aging resistance, mechanical properties and translucency of different yttria-stabilized zirconia ceramics for monolithic dental crown applications10.1016/j.dental.2018.03.006 ↗
51. The effect of extended aging on the optical properties of different zirconia materials10.1016/j.jpor.2016.11.002 ↗
52. Impact of hydrothermal aging on the light transmittance and flexural strength of colored yttria-stabilized zirconia materials of different formulations10.1016/j.prosdent.2020.01.016 ↗
53. External gap progression after cyclic fatigue of adhesive overlays and crowns made with high translucency zirconia or lithium silicate10.1111/jerd.12837 ↗
54. Optical properties of CAD/CAM monolithic system compared: Three multi-layered zirconia and one lithium disilicate system10.1016/j.heliyon.2021.e08151 ↗