journal article·2025-10

A Numerical Study on PV Performance of the Modeled Solar Cell Based on Y-doped CuO Thin Film Produced by Spin Coating

Şilan Baturay, Serap Yiğit Gezgin, Canan Aytuğ Ava, Hamdi Şükür Kiliç

Journal of Electronic Materials· Volume 54· Issue 10
Publisher page

Abstract

In this study, un-doped and yttrium-doped copper oxide (Y-doped CuO) samples were produced on glass using the spin coating technique. X-ray diffraction (XRD) patterns for the un-doped and Y-doped CuO demonstrated that all samples have a monoclinic polycrystalline structure, with two maximum peaks (−111)/(002) and (111). The crystallite parameters of the maximum peaks were changed with Y dopant content. Scanning electron microscopy images verified the presence of small aggregated particles on the film’s surfaces. It was observed that charge carrier concentration increased and mobility decreased in CuO thin film with increasing Y concentration. Ultraviolet–visible (UV–Vis) spectrophotometry measurements of the CuO samples revealed average transmittance of 30–40% in the visible region. It was also observed that the energy bandwidth decreased slightly with increasing Y concentration. In this study, the solar cell based on Y-doped CuO semiconductor with the most advanced crystal structure and lowest bandgap was modeled, using SCAPS-1D simulation software. The VOC, JSC, FF, and η values of the Y-doped CuO thin-film solar cell, whose production is sparsely reported in the literature, were calculated based on several physical parameters including interface defect density, electron affinity, work function of the back contact, and operating temperature, and its possible photovoltaic (PV) performance was determined. Depending on the change of these parameters, an improvement or deterioration in the performance of the solar cell was observed. The obtained data were then interpreted and expressed in detail according to the working principles of the solar cell. Thus, this study will allow doped CuO thin-film solar cell production studies to proceed with appropriate and safe steps.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Copper-based nanomaterials and applications · ZnO doping and properties · Chalcogenide Semiconductor Thin Films

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (84)

Show source-provided references
1. J. Sun and J. Jasieniak, Semi-transparent solar cells. J. Phys. D Appl. Phys. 50(9), 093001 (2017).
2. D.H. Shin and S.-H. Choi, Recent studies of semitransparent solar cells. Coatings 8(10), 329 (2018).10.3390/coatings8100329 ↗
3. C. Granqvist, Transparent conductive electrodes for electrochromic devices: a review. Appl. Phys. A 57, 19 (1993).10.1007/BF00331211 ↗
4. M.S. Sangeetha, S. Sarkar, A.R. Kulkarni, and A. Asok, Colloidal metal oxides and their optoelectronic and photonic applications, Metal oxides for next-generation optoelectronic, photonic, and photovoltaic applications. (Elsevier, 2024), pp. 373–407.
5. A.H. Jayatissa, K. Guo, and A.C. Jayasuriya, Fabrication of cuprous and cupric oxide thin films by heat treatment. Appl. Surf. Sci. 255(23), 9474 (2009).10.1016/j.apsusc.2009.07.072 ↗
6. Ş. Korkmaz, B. Geçici, S.D. Korkmaz, R. Mohammadigharehbagh, S. Pat, S. Özen, V. Şenay, and H.H. Yudar, Morphology, composition, structure and optical properties of CuO/Cu2O thin films prepared by RF sputtering method. Vacuum 131, 142 (2016).10.1016/j.vacuum.2016.06.010 ↗
7. P. Ctibor, L. Straka, F. Lukáč, J. Sedláček, and I. Králová, Copper oxides CuO and Cu2O processed by spark plasma sintering—electrical characterization and photo-activated conductivity. Boletín de la Sociedad Española de Cerámica y Vidrio 63(6), 413 (2024).10.1016/j.bsecv.2024.07.003 ↗
8. H.A.T. Vu, D.T. Pham, H.T. My, D.A. Duong, A.H. Alshehri, V.T. Tran, T.M.H. Nguyen, D.P. Congf, and V.-H. Nguyen Atmospheric pressure spatial atomic layer deposition of p-type CuO thin films from copper (ii) acetylacetonate and ozone for UV detection. Dalton Trans. 54(8), 3266 (2025).10.1039/D4DT02689F ↗
9. E. Arulkumar and S. Thanikaikarasan, Structure, morphology, composition, optical properties and catalytic activity of nanomaterials CuO, NiO CuO/NiO using methylene blue. Optik 302, 171685 (2024).10.1016/j.ijleo.2024.171685 ↗
10. T. Dimopoulos, A. Peić, P. Müllner, M. Neuschitzer, R. Resel, S. Abermann, M. Postl, E.J.W. List, S. Yakunin, W. Heiss, and H. Brückl, Photovoltaic properties of thin film heterojunctions with cupric oxide absorber. J. Renew. Sustain. Energy 5(1), 011205 (2013).10.1063/1.4791779 ↗
11. T.K. Wong, S. Zhuk, S. Masudy-Panah, and G.K. Dalapati, Current status and future prospects of copper oxide heterojunction solar cells. Materials 9(4), 271 (2016).10.3390/ma9040271 ↗
12. K. Leng, Y. Wan, Y. Fu, L. Wang, and Q. Wang, Si/CuO heterojunction-based photomemristor for reconfigurable, non-volatile, and self-powered in-sensor computing. Small 20, 2309945 (2024).10.1002/smll.202309945 ↗
13. M.E. Güldüren, D. İskenderoğlu, H. Güney, S.M. Karadeniz, M. Acar, and E. Gür, Structural, optical, and H2 gas sensing analyses of Cr doped CuO thin films grown by ultrasonic spray pyrolysis. Int. J. Hydrogen Energy 48(54), 20804 (2023).10.1016/j.ijhydene.2023.03.057 ↗
14. S. Ruzgar, Y. Caglar, O. Polat, D. Sobola, and M. Caglar, The tuning of electrical performance of Au/(CuO: La)/n-Si photodiode with La doping. Surf. Interfaces 21, 100750 (2020).
15. R. Aydın, A. Akkaya, and B. Şahin, Light-weight and flexible Ni-doped CuO (Ni: CuO) thin films grown using the cost-effective SILAR method for future technological requests. J. Mater. Sci.: Mater. Electron. 33(30), 23806 (2022).
16. S. Çetinkaya, Solution-based fabrication of copper oxide thin film influence of cobalt doping on structural, morphological, electrical, and optical properties. Turk. J. Eng. 8(1), 107 (2024).10.31127/tuje.1290655 ↗
17. S. Ruzgar, Y. Caglar, and M. Caglar, The optoelectrical properties of rare earth element Eu doped CuxO based heterojunction photodiode. Chin. J. Phys. 72, 587 (2021).10.1016/j.cjph.2021.05.017 ↗
18. M. Shaban, A.M. El Sayed, H. AlMohamadi, M.T. Khan, and A.M. Ahmed, Effects of transition metals (Fe, Co) on the physical and photoelectrochemical hydrogen generation properties of copper oxide nanoparticulate films. Int. J. Hydrogen Energy 56, 164 (2024).10.1016/j.ijhydene.2023.12.145 ↗
19. G. Rongrong, X. Hua, F. Gao, Z. Yang, J. Li, C. Zhang, G. Hodes, and S. Liu, CuO: Se composite films and its photovoltaic application. Mater. Today Commun. 33, 104848 (2022).
20. J. Husna, N.A. Jamil, K.S. Siow, T.R. Lenka, H. Kumar, P. Chelvanathan, M.A. Mohamed, and A.R. Zain, Numerical optimization of plasmonic CuO-based semi-transparent thin film solar cell device via L9 Taguchi orthogonal array method and ANOVA. Int. J. Integr. Eng. 16(9), 264 (2024).10.30880/ijie.2024.16.09.021 ↗
21. Y. Ait-Wahmane, H. Mouhib, B. Ydir, A. Ait Hssi, L. Atourki, A. Ihlal, and K. Bouabid, Comparison study between ZnO and TiO2 in CuO based solar cell using SCAPS-1D. Mater. Today: Proce. 52, 166 (2022).
22. S. Ahmmed, A. Aktar, S. Tabassum, M.H. Rahman, M.F. Rahman, and A.B.M. Ismail, CuO based solar cell with V2O5 BSF layer: theoretical validation of experimental data. Superlattices Microstruct. 151, 106830 (2021).10.1016/j.spmi.2021.106830 ↗
23. M. Hannachi, S. Belhadj, Z. Rouabah, N. Bouarissa, and A. Zoukel,Numerical study of a novel heterojunction solar cell a-Si: H (p)/CuO (P)/a-Si: H (n). Mater. Chem. Phys. 334, 130495 (2025).10.1016/j.matchemphys.2025.130495 ↗
24. J. Husna, P.S. Menon, P. Chelvanathan, M.A. Mohamed, S.K. Tripathy, and T.R. Lenka, Numerical study of semi-transparent thin film heterojunction p-CuO/n-ZnO/AZO/ITO solar cells device model using SCAPS-1D. Chalcogenide Lett. 18(11), 667 (2021).10.15251/CL.2021.1811.667 ↗
25. Z. El Hafidi, N. Outaleb, and Y. Naimi, Electrodeposition of ZnO thin films at low temperature: effects of deposition potential on properties for ZnO/CuO heterojunction solar cells. J. Mater. Sci.: Mater. Electron. 35(28), 1861 (2024).
26. R. Singh and S. Dutta, The role of pH and nitrate concentration in the wet chemical growth of nano-rods shaped ZnO photocatalyst. Nano-Struct. Nano-Objects 18, 100250 (2019).
27. M.M. Rahman, M.H. Ali, M.D. Haque, and A. Islam, Numerical modeling and extensive analysis of an extremely efficient RbGeI3-based perovskite solar cell by incorporating a variety of ETL and HTL materials to enhance PV performance. Energy Adv. 3(9), 2377 (2024).10.1039/D4YA00323C ↗
28. A. Saidarsan, S. Guruprasad, A. Malik, P. Basumatary, and D.S. Ghsh, A critical review of unrealistic results in SCAPS-1D simulations: Causes, practical solutions and roadmap ahead. Sol. Energy Mater. Sol. Cells 279, 113230 (2025).10.1016/j.solmat.2024.113230 ↗
29. S.G. Yiğit, A. Houimi, and H.Ş Kiliç, Comparison of electrical and photovoltaic parameters of the hetero-junction solar cells based on CZTS and CIGS ultrathin films. Mater. Technol. 37(10), 1573 (2022).10.1080/10667857.2021.1964215 ↗
30. A. Bhatnagar, A. Johari, and V. Janyani, Performance analysis of thin film CIGS solar cell at different values of thickness, bandgap and temperature through numerical simulation, in Nanoengineering: Fabrication, Properties, Optics, Thin Films, and Devices XVII. SPIE (2020)10.1117/12.2567882 ↗
31. S.Y. Gezgin, Modelling and investigation of the electrical properties of CIGS/n-Si heterojunction solar cells. Opt. Mater. 131, 112738 (2022).
32. S.Y. Gezgin and H.Ş Kiliç, The effect of Ag and Au contacts on the efficiency of CZTS/n-Si solar cell: the confirmation of experimental and theoretical results by SCAPS simulation. Braz. J. Phys. 52(4), 148 (2022).10.1007/s13538-022-01145-0 ↗
33. S. Heo, S.K. Sharma, S. Lee, Y. Lee, C. Kim, B. Lee, H. Lee, and D.Y. Kim, Effects of Y contents on surface, structural, optical, and electrical properties for Y-doped ZnO thin films. Thin Solid Films 558, 27 (2014).10.1016/j.tsf.2014.02.025 ↗
34. B.D. Cullity and R. Smoluchowski, Elements of X-ray Diffraction. Phys. Today 10(3), 50 (1957).10.1063/1.3060306 ↗
35. L. Vimala Devi, T. Selvalakshmi, S. Sellaiyan, P.S. Murphin Kumar, and S. Sankar, Combustion derived Y doped CuO nanoparticle: its structural, morphological and optical properties. J. Mater. Sci.: Mater. Electron. 29, 9387 (2018).
36. S. Sellaiyan, L.V. Devi, K. Sako, A. Uedono, and K. Sivaji, Effect of dopant concentration and annealing of Yttrium doped CuO nanocrystallites studied by positron annihilation spectroscopy. J. Alloy. Compd. 788, 549 (2019).10.1016/j.jallcom.2019.02.247 ↗
37. M. Thirumoorthi and J.T.J. Prakash, Structural, morphological characteristics and optical properties of Y doped ZnO thin films by sol–gel spin coating method. Superlattices Microstruct. 85, 237 (2015).10.1016/j.spmi.2015.05.005 ↗
38. Z.N. Kayani, M. Anjum, S. Riaz, S. Naseem, and T. Zeeshan, Role of Mn in biological, optical, and magnetic properties ZnO nano-particles. Appl. Phys. A 126, 1 (2020).10.1007/s00339-019-3176-6 ↗
39. Z.N. Kayani, W. Chaudhry, R. Sagheer, M. Anjum, S. Riaz, and S. Naseem, Effect of Ce doping on crystallite size, band gap, dielectric and antibacterial properties of photocatalyst copper oxide Nano-structured thin films. Mater. Sci. Eng., B 283, 115799 (2022).
40. T. Jan, J. Iqbal, Q. Mansoor, M. Ismail, M.S.H. Naqvi, A. Gul, S.F.H. Naqvi, and F. Abbasynthesis, Synthesis, physical properties and antibacterial activity of Ce doped CuO: a novel nanomaterial. J. Phys. D Appl. Phys. 47(35), 355301 (2014).
41. S.A. Vanalakar, G.L. Agawane, A.S. Kamble, C.W. Hong, P.S. Patil, and J.H. Kim, Fabrication of Cu2SnS3 thin film solar cells using pulsed laser deposition technique. Sol. Energy Mater. Sol. Cells 138, 1 (2015).10.1016/j.solmat.2015.02.031 ↗
42. S. Yiğit Gezgin and H.Ş Kiliç, The effect of Ag plasmonic nanoparticles on the efficiency of CZTS solar cell: an experimental investigation and numerical modelling. Indian J. Phys. 97(3), 779 (2023).10.1007/s12648-022-02453-6 ↗
43. M. Alla, V. Manjunath, E. Choudhary, M. Samtham, S. Sharma, P.A. Shaikh, M. Rouchdi, and B. Fares, Evaluating the potential of lead-free Nontoxic Cs2BiAgI6-based double perovskite solar cell. Physica Status Solidi (A) 220(2), 2200642 (2023).10.1002/pssa.202200642 ↗
44. M.R. Mahbub, S. Islam, F. Anwar, S.S. Satter, and S.M. Ullah. Simulation of CZTS thin film solar cell for different buffer layers for high efficiency performance. South Asian J. Eng.Technol. 2(52), 1 (2016).
45. T.D. Veal, D.O. Scanlon, R. Kostecki, and E. Arca Accelerating the development of new solar absorbers by photoemission characterization coupled with density functional theory. J. Phys.: Energy 3(3), 032001 (2021).
46. A.S. Najm, P. Chelvanathan, S.K. Tiong, M.T. Ferdaous, S.A. Shahahmadi, Y. Yusoff, K. Sopian, and N. Amin, Numerical insights into the influence of electrical properties of n-CdS buffer layer on the performance of SLG/Mo/p-absorber/n-CdS/n-ZnO/Ag configured thin film photovoltaic devices. Coatings 11(1), 52 (2021).10.3390/coatings11010052 ↗
47. K. Kaur and M. Kumar, Progress and prospects of CZTSSe/CdS interface engineering to combat high open-circuit voltage deficit of kesterite photovoltaics: a critical review. J. Mater. Chem. A 8(41), 21547 (2020).10.1039/D0TA06450E ↗
48. A. Melliti, Numerical prediction and optimization of the performance of CCTS-based thin film solar cell. Optik 281, 170837 (2023).10.1016/j.ijleo.2023.170837 ↗
49. C. Tamin, D. Chaumont, O. Heintz, R. Chassagnon, A. Leray, N. Geoffroy, M. Guerineau, and M. Adnane, Investigation of absorber and heterojunction in the pure sulphide kesterite. Boletín de la Sociedad Española de Cerámica y Vidrio 60(6), 380 (2021).10.1016/j.bsecv.2020.05.004 ↗
50. D.A. Fentahun, A. Tyagi, and K.K. Kar, Numerically investigating the AZO/Cu2O heterojunction solar cell using ZnO/CdS buffer layer. Optik 228, 166228 (2021).10.1016/j.ijleo.2020.166228 ↗
51. R. Malani, T. Pansuriya, and V. Kheraj, A study on influence of potential defects and optimization of device structure for CuSbS2 based thin film solar cell using SCAPS–1D simulator. Opt. Mater. 133, 112910 (2022).10.1016/j.optmat.2022.112910 ↗
52. R. Malani, T. Pansuriya, and V. Kheraj, A numerical simulation of high efficiency CdS/CdTe based solar cell using NiO HTL and ZnO TCO. Optik 223, 165625 (2020).
53. A. Živković and N.H. de Leeuw, Exploring the formation of intrinsic p-type and n-type defects in CuO. Phys. Rev. Mater. 4(7), 074606 (2020).
54. N.K. Singh, A. Agarwal, and T. Kanumuri, Investigation of electrical parameters of CdTe photovoltaic devices by computational analysis. Physica Status Solidi (A) 219(3), 2100326 (2022).10.1002/pssa.202100326 ↗
55. R. Jaiswal, R. Ranjan, N. Srivastava, A.K. Sharma, M. Yoshimura, L. Chang, and R.N. Tiwari, Numerical study of eco-friendly Sn-based perovskite solar cell with 25.48% efficiency using SCAPS-1D. J. Mater. Sci. Mater. Electron. 34(8), 753 (2023).10.1007/s10854-023-10171-w ↗
56. S.R. Hosseini, M. Bahramgour, P.Y. Sefidi, A.T. Mashayekh, A. Moradi, N. Delibas, M.G. Hosseini, and A. Niaei, Investigating the effect of non-ideal conditions on the performance of a planar CH3NH3PbI3-based perovskite solar cell through SCAPS-1D simulation. Heliyon (2022). https://doi.org/10.1016/j.heliyon.2022.e11471.10.1016/j.heliyon.2022.e11471 ↗
57. S. Paul, R. Lopez, M.D. Mia, C.H. Swartz, and J.V. LiA, A simulation study on radiative recombination analysis in CIGS Solar cell, in 2017 IEEE 44th Photovoltaic Specialist Conference (PVSC). 2017.10.1109/PVSC.2017.8521498 ↗
58. N.S. Noorasid, F. Arith, A.N. Mustafa, P. Chelvanathan, M.I. Hossain, M.A. Azam, and N. Amin, Improved performance of lead-free Perovskite solar cell incorporated with TiO2 ETL and CuI HTL using SCAPs. Appl. Phys. A 129(2), 132 (2023).10.1007/s00339-022-06356-5 ↗
59. S. Yasin, T. Al Zoubi, and M. Moustafa, Design and simulation of high efficiency lead-free heterostructure perovskite solar cell using SCAPS-1D. Optik 229, 166258 (2021).10.1016/j.ijleo.2021.166258 ↗
60. J. Singh, S. Singh, V. Srivastava, S.R.K. Yadav, P. Lohia, and D.K. Dwivedi, Performance enhancement of PbS-TBAI quantum dot solar cell with MoTe2 as hole transport layer. Physica Status Solidi (A) 220(15), 2300275 (2023).10.1002/pssa.202300275 ↗
61. F. Baig, Y.H. Khattak, B. Mari, S. Beg, A. Ahmed, and K. Khan, Efficiency enhancement of CH 3 NH 3 SnI 3 solar cells by device modeling. J. Electron. Mater. 47, 5275 (2018).10.1007/s11664-018-6406-3 ↗
62. S. Imani, S.M. Seyed-Talebi, J. Beheshtian, and E.W.G. Diau, Simulation and characterization of CH3NH3SnI3-based perovskite solar cells with different Cu-based hole transporting layers. Appl. Phys. A 129(2), 143 (2023).10.1007/s00339-023-06428-0 ↗
63. M. Moustafa, T. Al Zoubi, and S. Yasin, Numerical analysis of the role of p-MoSe2 interfacial layer in CZTSe thin-film solar cells using SCAPS simulation. Optik 247, 167885 (2021).10.1016/j.ijleo.2021.167885 ↗
64. H. Dixit, S. Porwal, B. Boro, M. Paul, S. Ghosh, S. Mishra, and T. Singh A theoretical exploration of lead-free double perovskite La2NiMnO6 based solar cell via SCAPS-1D. Opt. Mater. 131, 112611 (2022).10.1016/j.optmat.2022.112611 ↗
65. H. Kafashan and A. Bahrami, CIGS solar cells using ZrS2 as buffer layer: Numerical simulation. Optik 298, 171594 (2024).10.1016/j.ijleo.2023.171594 ↗
66. H. Dixit, N.K. Bansal, S. Porwal, D. Kumar, and T. Singh, Performance assessment of earth-abundant Kesterite and lead-free chalcogenide-based perovskite solar cells using SCAPS-1D. Optik 295, 171474 (2023).10.1016/j.ijleo.2023.171474 ↗
67. L. You, X. Zhang, Q. Ma, W. Zhu, and J. Wu, Optimization of electron transport layer-free Cs 2 TiBr 6/MASnBr 3 laminated structure perovskite solar cells by SCAPS-1D simulation. Physica Status Solidi. A Appl. Mater. Sci. (Online), 220(14): pp. 1-9 (2023)10.1002/pssa.202300071 ↗
68. A. Kaphle, E. Echeverria, D.N. Mcllroy, and P. Hari, Enhancement in the performance of nanostructured CuO–ZnO solar cells by band alignment. RSC Adv. 10(13), 7839–7854 (2020).10.1039/C9RA10771A ↗
69. R. Özmenteş, C. Temirci, A. Ozkartal, K. Ejderha, and N. Yildirim, Characterization of CuO/n-Si heterojunction solar cells produced by thermal evaporation. Mater. Sci.-Pol. 36(4), 668 (2018).10.2478/msp-2018-0092 ↗
70. S.A. Makki and H.M. Ali, Fabrication and characterization of P-Cuo/N-Si heterojunction for solar cell applications. J. Multidisc. Eng. Sci. Technol. 3, 2458 (2016).
71. F. Gao, X.J. Liu, J.S. Zhang, M.Z. Song, and N. Li, Photovoltaic properties of the p-CuO/n-Si heterojunction prepared through reactive magnetron sputtering. J. Appl. Phys. (2012). https://doi.org/10.1063/1.4704382.10.1063/1.4704382 ↗
72. R. Özmenteş, Current-voltage characteristics of p-CuO/n-Si heterojunction for solar cell application. Mater. Today Proc. 46, 7010 (2021).10.1016/j.matpr.2021.03.281 ↗
73. S. Masudy-Panah, G.K. Dalapati, K. Radhakrishnan, A. Kumar, and H.R. Tan, Reduction of Cu-rich interfacial layer and improvement of bulk CuO property through two-step sputtering for p-CuO/n-Si heterojunction solar cell. J. Appl. Phys. 116(7), 074501 (2014).10.1063/1.4893321 ↗
74. S. Masudy-Panah, G.K. Dalapati, K. Radhakrishnan, A. Kumar, H.R. Tan, E.N. Kumar, C. Vijila, C.C. Tan, and D.Z. Chi, P-CuO/n-Si heterojunction solar cells with high open circuit voltage and photocurrent through interfacial engineering. Prog. Photovolt. Res. Appl. 23(5), 637 (2015).10.1002/pip.2483 ↗
75. S. Masudy-Panah, K. Radhakrishnan, T.H. Ru, R. Yi, T.I. Wong, and G.K. Dalapati, In situ codoping of a CuO absorber layer with aluminum and titanium: the impact of codoping and interface engineering on the performance of a CuO-based heterojunction solar cell. J. Phys. D Appl. Phys. 49(37), 375601 (2016).10.1088/0022-3727/49/37/375601 ↗
76. C. Jayathilaka, V. Kapaklis, W. Siripala, and S. Jayanetti, Improved efficiency of electrodeposited p-CuO/n-Cu2O heterojunction solar cell. Appl. Phys. Express 8(6), 065503 (2015).10.7567/APEX.8.065503 ↗
77. A. Bhaumik, A. Haque, P. Karnati, M.F.N. Taufique, R. Patel, and K. Ghoshoxide, based nanostructures for improved solar cell efficiency.Thin Solid Films 572, 126 (2014).10.1016/j.tsf.2014.09.056 ↗
78. V. Kumar, A. Kaphle, R. Rathnasekara, G.R. Neupane, and P. Hari, Role of Al doping in morphology and interface of Al-doped ZnO/CuO film for device performance of thin film-based heterojunction solar cells. Hybrid Adv. 5, 100148 (2024).
79. A. Kuddus, M.F. Rahman, S. Tabassum, J. Hossain, and A.B.M. Ismail, Study on the performance of ZnO/CuO Heterojunction Solar Cell Simulation and Experimental, in 2019 International Conference on Computer, Communication, Chemical, Materials and Electronic Engineering (IC4ME2). IEEE (2019)10.1109/IC4ME247184.2019.9036573 ↗
80. S.F. Hasan, O.A. Fahad, A.Z. Al-Jenaby, and A.S. Mohammed, High performances multi-function of FTO/ZnO/CuO/Al Heterojunction device: gas sensor and solar cell. J. Opt. 1 (2024)10.1007/s12596-024-02349-0 ↗
81. S.H. Lee, M. Shin, S.J. Yun, and J.W. Lim, CuOx/a-Si: H heterojunction thin-film solar cell with an n-type µc-Si: H depletion-assisting layer. Prog. Photovolt. Res. Appl. 23(11), 1642 (2015).10.1002/pip.2603 ↗
82. R. Bhunia, S. Dolai, R. Dey, S. Das, S. Hussain, R. Bhar, and A. Pal, Fabrication and characterization of cu/Cu2O/CuO/ZnO/Al–ZnO/ag heterojunction solar cells. Semicond. Sci. Technol. 33(10), 105007 (2018).10.1088/1361-6641/aad8d3 ↗
83. A.S. Mohammed, A. Ramizy, H.H. Hussain, F.A.H. Mutlak, and S.A. Thamir, Performance evaluation of Ag/WO3/CuO/Si heterojunction solar cell: the effect of window layer thickness. Plasmonics. pp 1 (2024)10.1007/s11468-024-02526-8 ↗
84. J. Sultana, S. Paul, R. Saha, S. Sikdar, A. Karmakar, and S. Chattopadhyay, Optical and electronic properties of chemical bath deposited p-CuO and n-ZnO nanowires on silicon substrates: p-CuO/n-ZnO nanowires solar cells with high open-circuit voltage and short-circuit current. Thin Solid Films 699, 137861 (2020).10.1016/j.tsf.2020.137861 ↗