journal article·2022-06Open access

Highly transparent and conductive MoO3/Ag/MoO3 multilayer films via air annealing of the MoO3 layer for ITO-free organic solar cells

Po-Ching Kao, Ching-Jui Hsu, Ze-Hui Chen, Sy-Hann Chen

Abstract

Air annealing of MoO 3 bottom layer is a simple and highly efficient surface treatment method to prepare ultrathin, continuous, and smooth Ag layers in MoO 3 /Ag/MoO 3 (MAM) transparent conductive films (TCFs) for indium tin oxide (ITO)-free organic solar cells (OSCs). Air annealing can readily oxidize MoO 3 surface and increase surface energy of the MoO 3 layer, which significantly enhances the adhesion between Ag and MoO 3 . When the MoO 3 bottom layer is annealed at 200 °C, moreover, the treatment yields a flatter MoO 3 surface, which positively influences the growth of Ag nanostructures . Eventually, an almost homogeneous, smooth, and continuous surface morphology of the ultrathin Ag films with a thickness of 6.5 nm was obtained. By employing air-annealed MoO 3 bottom layer, the MoO 3 (200 °C, 10 min)/Ag (6.5 nm)/MoO 3 TCF had higher optical transmittance (T av = 83.6%) and lower sheet resistance (R s = 6.5 Ω/sq) than unannealed MAM or commercial ITO TCFs, thereby obtaining the higher value of figure of merit (F TC = 2.6 ×10 −2 Ω −1 ). When used as the transparent electrode in organic solar cells (OSCs), the improved optoelectrical properties of the MoO 3 (200 °C, 10 min)/Ag (6.5 nm)/MoO 3 electrode result in increased short-circuit current density (J sc = 2.27 mA cm −2 ) and fill factor (FF = 54.8%) of OSCs in comparison to devices based on unannealed MAM and ITO electrodes, leading to an improvement in power conversion efficiency (PCE = 0.62%). From the results of photocurrent measurements, air annealing MoO 3 increases exciton generation in active layers and reduces the carrier back-transfer induced recombination at the anode contact, yielding the enhanced photovoltaic performance .
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Perovskite Materials and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Charge photogeneration in organic solar cells10.1021/cr900271s ↗
2. Organic solar cell materials toward commercialization10.1002/smll.201801793 ↗
3. Morphology control in organic solar cells10.1002/aenm.201703147 ↗
4. Transparent electrodes for organic optoelectronic devices: a review10.1117/1.JPE.4.040990 ↗
5. Enhancement of light extraction efficiency of organic light emitting diodes using nanostructured indium tin oxide10.1364/OL.37.000575 ↗
6. Avoiding indium10.1038/nphoton.2011.46 ↗
7. Development of inverted OLED with top ITO anode by plasma damage-free sputtering
8. Performance of flexible polymeric light-emitting diodes under bending conditions10.1063/1.1574400 ↗
9. ZnO/Ag/ZnO multilayer transparent electrode for highly-efficient ITO-Free polymer solar cells10.1016/j.cap.2020.01.003 ↗
10. Promising ITO-free perovskite solar cells with WO3-Ag-SnO2 as transparent conductive oxide10.1039/C8TA08287A ↗
11. High performance organic light-emitting diodes employing ITO-free and flexible TiOx/Ag/Al:ZnO electrodes10.1039/D1RA02214H ↗
12. Low-temperature oxide/metal/oxide multilayer films as highly transparent conductive electrodes for optoelectronic devices10.1021/acsaem.1c00586 ↗
13. TCO/metal/TCO structures for energy and flexible electronics10.1016/j.tsf.2011.06.091 ↗
14. Toward indium-free optoelectronic devices: dielectric/metal/dielectric alternative conductive transparent electrode in organic photovoltaic cells
15. Roll-to-Roll sputtered ITO/Cu/ITO multilayer electrode for flexible, transparent thin film heaters and electrochromic applications10.1038/srep33868 ↗
16. Improvement of transparent metal top electrodes for organic solar cells by introducing a high surface energy seed layer10.1002/aenm.201200903 ↗
17. The structure of evaporated metal films and their optical properties10.1364/JOSA.40.000203 ↗
18. Ultrathin and ultrasmooth Au films as transparent electrodes in ITO-free organic light-emitting devices10.1039/C6NR00599C ↗
19. Ultrathin silver film electrodes with ultralow optical and electrical losses for flexible organic photovoltaics10.1021/acsami.8b08578 ↗
20. Optical and structural properties of ultra-thin gold films10.1002/adom.201400345 ↗
21. Bendable solar cells from stable, flexible, and transparent conducting electrodes fabricated using a nitrogen-doped ultrathin copper film10.1002/adfm.201600392 ↗
22. Intrinsic optical properties and enhanced plasmonic response of epitaxial silver10.1002/adma.201401474 ↗
23. Design of transparent anodes for resonant cavity enhanced light harvesting in organic solar cells10.1002/adma.201104273 ↗
24. UV-ozone treated graphene oxide/PEDOT: PSS bilayer as a novel hole transport layer in highly efficient and stable organic solar cells10.1016/j.orgel.2018.12.005 ↗
25. Hydrogen plasma-treated MoSe2 nanosheets enhance the efficiency and stability of organic photovoltaics10.1039/C9NR06611J ↗
26. Physical properties of RF sputtered ITO thin films and annealing effect10.1088/0022-3727/39/1/027 ↗
27. Highly efficient inverted polymer solar cell by low temperature annealing of Cs2CO3 interlayer10.1063/1.2918983 ↗
28. Artificially MoO3 graded ITO anodes for acidic buffer layer free organic photovoltaics10.1016/j.apsusc.2015.12.171 ↗
29. Properties of MoO3 films by thermal oxidation: annealing induced phase transition10.1166/mex.2013.1114 ↗
30. Li-ion intercalation in thermal oxide thin films of MoO3 as studied by XPS, RBS, and NRA10.1021/jp800147f ↗
31. Enhanced photocatalytic activity of amorphous MoO3 thin films deposited by rf reactive magnetron sputtering10.1016/j.cattod.2018.04.065 ↗
32. Effect of a CdSe layer on the thermo- and photochromic properties of MoO3 thin films deposited by physical vapor deposition10.1021/acs.jpcc.9b02895 ↗
33. XPS and X-ray diffraction characterization of MoO3 thin films prepared by laser evaporation
34. Investigation of surface energy for organic light emitting polymers and indium tin oxide10.1016/S0040-6090(00)00994-9 ↗
35. Oxide surface cleaning by an atmospheric pressure plasma10.1016/j.surfcoat.2003.08.011 ↗
36. Growth of thin films of molybdenum oxide by atomic layer deposition10.1039/C0JM01099E ↗
37. The effect of substrate surface roughness on ZnO nanostructures growth10.1016/j.apsusc.2010.11.005 ↗
38. Optical recording characteristics of molybdenum oxide films prepared by pulsed laser deposition method10.1016/j.tsf.2008.09.060 ↗
39. The evolution of the Mo5+ oxidation state in the thermochromic effect of MoO3 thin films deposited by rf magnetron sputtering10.1016/j.jallcom.2017.06.149 ↗
40. An XPS study of the UV reduction and photochromism of MoO3 and WO310.1063/1.443047 ↗
41. New figure of merit for transparent conductors10.1063/1.323240 ↗
42. Highly flexible, conductive and transparent MoO3/Ag/MoO3 multilayer electrode for organic photovoltaic cells10.1016/j.tsf.2013.07.048 ↗
43. Indium-free multilayer semi-transparent electrodes for polymer solar cells10.1016/j.solmat.2015.10.010 ↗
44. Improvement of MoO3/Ag/MoO3 multilayer transparent electrodes for organic solar cells by using UV-ozone treated MoO3 layer10.1016/j.solmat.2018.06.031 ↗
45. Photocurrent generation in polymer-fullerene bulk heterojunctions10.1103/PhysRevLett.93.216601 ↗
46. High efficiency P3HT:PCBM solar cells with an inserted PCBM layer10.1039/c4tc00003j ↗
47. Surface plasmonic effects of metallic nanoparticles on the performance of polymer bulk heterojunction solar cells10.1021/nn102295p ↗
48. Optical and electrical effects of gold nanoparticles in the active layer of polymer solar cells10.1039/C1JM14150C ↗