journal article·2024-04

Effect of Mn addition in W-Ni-Cu heavy alloy processed through hot press sintering techniques on microstructure, microtexture and grain boundary character evolution

Manikandan R, Raja Annamalai A

Publisher page

Abstract

In this current study, the impact of manganese addition to 93 W-4.9Ni-2.1Cu-xMn (where x = 1, 2, 3, and 4 Wt%) on the microstructure, texture development, and grain boundary character distribution of tungsten heavy alloy (WHAs) was examined. The samples were produced through a vacuum hot press sintering, with parameters 50 MPa pressure, 10 °C/min heating rate, and 1450 °C sintering temperature for 20 min holding duration. To study the influence of manganese on the texture development and microstructure in conventional WHAs, electron backscatter diffraction (EBSD) was employed. The important findings from the EBSD analysis reveal that fibre texture (001) 〈111〉 and a higher fraction of low-angle grain boundaries in the Mn unalloyed compact resulted from extensive atomic jumps between the particles at elevated temperatures. Further texture analysis on the Mn-added compacts reveals that manganese oxide (MnO) formation during liquid phase sintering led to lower densification and randomized weak fibre texture development in manganese-alloyed compacts. In addition, the texture degradation in Mn-added compacts is mainly caused by recrystallization followed by sub-structural recovery during liquid phase sintering. This study indicates that increasing manganese content in WHAs stoichiometry led to a heterogeneous distribution of binder matrix (Ni Cu) in the sintered compact. As a result, W-4.9Ni-2.1Cu-4Mn alloy revealed decreased relative density (90.70%), microhardness (389.5 HV 0.5 ), and electrical conductivity (15.74% of IACS).
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Fusion materials and technologies · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. German · 2021
2. Effect of Fe addition in W-Ni-cu heavy alloy processed through powder metallurgy on microstructure and mechanical properties10.1016/j.jallcom.2023.172578 ↗
3. Microstructure and mechanical properties of tungsten heavy alloy prepared using tungsten metal powder produced from heavy alloy scrap10.14429/dsj.73.18722 ↗
4. Preparation and penetration behavior of the reactive fine-grained tungsten heavy alloy
5. High entropy alloy: a promising matrix for high-performance tungsten heavy alloys10.1016/j.jallcom.2018.11.089 ↗
6. Development and properties of new tungsten-based composites for penetrators
7. Microstructural study of adiabatic shear bands formed by high-speed impact in a tungsten heavy alloy penetrator mater10.1016/S0921-5093(98)00565-6 ↗
8. Effect of two-time spark plasma sintering on microstructure and mechanical properties of W–6Ni–4Mn alloy10.1016/j.msea.2018.12.109 ↗
9. Young, Timothy Howard · 2012
10. Development of a new W-Ni-Mn heavy alloy
11. Effects of atmosphere temperature and composition on densification of nickel-tungsten-manganese alloys10.1016/0026-0657(92)91935-D ↗
12. Manikandan · 2022
13. A study on the improvement of the sintered density of W-Ni-Mn heavy alloy10.1007/s11663-997-0011-9 ↗
14. Hong · US Patent No. · 1999 · 5 · 970,307
15. Texture and structure evolution of tantalum powder samples during spark plasma sintering and conventional hot-pressing10.1016/j.ijrmhm.2006.10.001 ↗
16. A boundary-based approach to the multiscale microstructural characterization of a W-Ni-Fe tungsten heavy alloy10.1016/j.scriptamat.2022.114587 ↗
17. Crystallographic texture and grain boundary character development of hot-press sintered tungsten heavy alloy: the effect of rhenium concentration10.1016/j.matchemphys.2023.128621 ↗
18. The roles of oriented nucleation and oriented growth on recrystallization textures in commercial purity aluminium
19. Modeling of recrystallization textures: interaction of nucleation and growth10.1016/S1359-6454(02)00020-4 ↗
20. Model calculations of primary recrystallization textures10.1016/0956-716X(92)90141-Z ↗
21. Evolution of crystallographic texture and grain boundary character in hot press sintered tungsten heavy alloy as a function of sintering temperature10.1016/j.matlet.2023.134125 ↗
22. Microstructures and properties of 90W-4Ni-6Mn alloy prepared by vacuum sintering
23. The effect of manganese addition on the microstructure of W–Ni–Fe heavy alloy10.1007/s11661-999-0054-4 ↗
24. Structural, microstructral, mechanical and magnetic characterization of ball milled tungsten heavy alloys10.4236/ampc.2014.412027 ↗
25. J, extended x- ray absorption fine structure of metastable bcc and fcc phases in mechanically alloyed Fe–cu10.1063/1.116736 ↗
26. The effects of alloying and milling on the formation of intermetallics in ODS tungsten heavy alloys10.1016/j.intermet.2013.04.014 ↗
27. M, development of a tungsten heavy alloy: W-Ni-Mn used as kinetic energy penetrator
28. Effect of processing parameters on microstructure and mechanical properties of 90W–6Ni–4Mn heavy alloy10.1016/j.ijrmhm.2014.09.024 ↗
29. Ostwald ripening during liquid phase sintering : effect of volume fraction on coarsening kinetics10.1007/BF02644701 ↗
30. E, phase diagram of the cu-Ni-Mn system10.3103/S1067821213020065 ↗
31. Effect of Mn/Ni ratio variation on microstructure of W–Ni–Mn alloy10.1179/174329007X204885 ↗
32. Ostwald ripening kinetics of angular grains dispersed in a liquid phase by two-dimensional nucleation and abnormal grain growth10.1016/S0955-2219(01)00370-3 ↗
33. The kinetics of precipitation from supersaturated solid solutions10.1016/0022-3697(61)90054-3 ↗
34. The Manganese--Tungsten System
35. On the relationship between grain boundary character distribution and intergranular corrosion10.1016/S1359-6462(97)00018-3 ↗
36. Randle · 1996
37. Int. J. Refract. Met. Hard Mater. · 2015 · 50 · 18410.1016/j.ijrmhm.2015.01.008 ↗
38. Atomistic simulations of interactions between the 1/2〈111〉 edge dislocation and symmetric tilt grain boundaries in tungsten10.1080/14786430801894577 ↗
39. Coarsening and grain growth in sintering of two particles of different sizes10.1016/j.actamat.2004.11.029 ↗
40. The ideal tensile strength and deformation behavior of a tungsten single crystal10.1016/j.nimb.2009.06.088 ↗
41. Kumar · 2002
42. Cold rotary swaging of a tungsten heavy alloy: numerical and experimental investigations10.1016/j.ijrmhm.2016.10.005 ↗
43. Microstructure and texture of polycrystalline CVD-ZnS analyzed via EBSD10.1002/adfm.201103131 ↗
44. Influence of microstructure on crack initiation and propagation behavior in swaged tungsten heavy alloy during Charpy impact process10.1016/j.msea.2022.144219 ↗
45. Recrystallization and grain growth induced by ELMs-like transient heat loads in deformed tungsten samples10.1038/srep06845 ↗
46. Recrystallization mechanisms and microstructure development in emerging metallic materials: a review
47. Effect of tungsten content and compression on microstructure and texture evolution in liquid phase sintered heavy alloy10.1007/s11661-021-06586-x ↗
48. A boundary-based approach to the multiscale microstructural characterization of W-Ni-Fe tungsten heavy alloy10.1016/j.scriptamat.2022.114587 ↗
49. Microstructure and texture evolution in warm-rolled fine-grained tungsten
50. Neck growth kinetics during microwave sintering of nickel powder10.1016/j.jallcom.2010.10.042 ↗
51. I, texture formation in metal alloys with cubic crystal structures10.1080/02670836.2016.1231746 ↗
52. Wenk Hans Rudolf · 2013
53. Engler · 2009
54. Kocks · 2000
55. Satyam · 2014
56. Hosford · 2010