journal article·2019-01Open access

Compressive performance and deformation mechanism of the dynamic gas injection aluminum foams

Ningzhen Wang, Eric Maire, Xiang Chen, Jérôme Adrien, Yanxiang Li, Yasin Amani, Lei Hu, Ying Cheng

Abstract

The dynamic gas injection method with high-speed horizontal oscillation could reduce the cell size and improve the cell quality of aluminum foams, so it is of interest to study the compressive performance and deformation mechanism of the foams produced with this process. In-situ compression in X-ray tomography was used for this research. Results have shown that the plateau stresses of bulk aluminum foams prepared by the dynamic gas injection method are in the range of 0.3 ~ 11 MPa. When the cell size is reduced to around 1 mm, the plateau stress could reach 22 MPa. In addition, the brittle deformation characteristics of aluminum foams in the quasi-static compression process are obvious. The dynamic gas injection method could greatly improve the mechanical properties of aluminum foams, and aluminum foams prepared by this method have a better compressive performance compared to that prepared by static method even at the same relative density. The uniformity of the cell size and sphericity also affects the mechanical properties. The result of in-situ compression shows that there are two main failure modes for cell walls of aluminum foams: the fracture after buckles of the cell walls and the direct fracture of the cell walls. The aluminum foams prepared by the dynamic gas injection method could have a wide application prospect due to its superior compressive performance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Cellular and Composite Structures · Pickering emulsions and particle stabilization · Polymer Foaming and Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Light-metal foams-history of innovation and technological challenges10.1002/adem.201200217 ↗
2. Manufacture, characterisation and application of cellular metals and metal foams10.1016/S0079-6425(00)00002-5 ↗
3. Gibson · 1997
4. Compressive and tensile behaviour of aluminum foams10.1016/S0921-5093(99)00170-7 ↗
5. Microstructure and mechanical properties of ALPORAS closed-cell aluminium foam10.1016/j.matchar.2015.07.012 ↗
6. Mechanical behaviour and energy absorption of closed-cell aluminium foam panels in uniaxial compression10.1016/j.msea.2009.03.067 ↗
7. Effects of cell wall property on compressive performance of aluminum foams10.1016/S1003-6326(15)63766-9 ↗
8. Compressive response of a closed-cell aluminum foam at high strain rate10.1016/j.scriptamat.2005.10.062 ↗
9. Comparison of quasi-static and dynamic compression behavior of closed-cell aluminum foam10.1016/j.msea.2009.07.017 ↗
10. Porous metals and metallic foams: current status and recent developments10.1002/adem.200800241 ↗
11. Modeling of macro-deformation behavior of thin-walled aluminum foam by gas injection method10.1007/s11665-017-2766-8 ↗
12. Foaming process and properties of 6063 aluminum foams by melt foaming method10.2320/matertrans.M2016244 ↗
13. The influence of pure Al and hypoeutectic Al-Si alloy base materials on the cell structures of aluminum foams produced by gas injection foaming process
14. The effect of cell wall microstructure on the deformation and fracture of aluminium-based foams10.1016/S1359-6454(01)00072-6 ↗
15. Micro–macro investigation of deformation and failure in closed-cell aluminum foams10.1016/j.commatsci.2013.10.017 ↗
16. Effects of cell size and cell wall thickness variations on the strength of closed-cell foams10.1016/j.ijengsci.2017.08.006 ↗
17. On the mechanical performance of closed cell Al alloy foams10.1016/S1359-6454(97)00148-1 ↗
18. Comparison of aluminium foams produced by melt foaming and gas injection processes
19. Aluminum foams produced by liquid-state processes10.1016/S1359-6454(98)00017-2 ↗
20. 2D and 3D characterization of metal foams using X-ray tomography10.1002/1527-2648(20021014)4:10<803::AID-ADEM803>3.0.CO;2-D ↗
21. Development of a foaming process for particulate reinforced aluminum melts10.1002/1527-2648(20021014)4:10<735::AID-ADEM735>3.0.CO;2-Y ↗
22. I. Jin, L. D. Kenny, H. Sang, Method of producing lightweight foamed metal, USA Patent 4973358 (1990).
23. The stability of aluminum foams at accumulation and condensation stages in gas injection foaming process10.1016/j.colsurfa.2015.06.043 ↗
24. Properties of aluminum foam prepared by gas injection method
25. Foamability of particle reinforced aluminum melt10.1002/mawe.200390011 ↗
26. H. Sang, L.D. Kenny, I. Jin, Process for producing shaped slabs of particle stabilized foamed metal, USA Patent 5334236 (1994).
27. Babcsán · 2012
28. Sub-mm sized bubbles injected into metallic melts10.1016/j.colsurfa.2014.12.038 ↗
29. The cell size reduction of aluminum foam with dynamic gas injection based on the improved foamable melt10.1016/j.colsurfa.2017.05.023 ↗
30. Compressive properties of aluminum foams by gas injection method
31. Pilot production and properties of ALUHAB aluminium foams, procedia
32. Cell structure and compressive behavior of an aluminum foam10.1007/s10853-005-2852-4 ↗
33. Macro and micro collapse mechanisms of closed-cell aluminium foams during quasi-static compression10.1016/j.matdes.2017.01.011 ↗
34. In-situ quasistatic compression and microstructural characterization of aluminium foams of different cell topology
35. Deformation mechanisms of closed-cell aluminum foam in compression10.1016/j.scriptamat.2010.05.041 ↗
36. Fracture mechanisms and size effects of brittle metallic foams: in situ compression tests inside SEM10.1016/j.compscitech.2008.04.023 ↗
37. Finite element simulation of the plastic collapse of closed-cell aluminum foams with X-ray computed tomography10.1016/j.mechmat.2010.01.003 ↗
38. Two-scale study of the fracture of an aluminum foam by X-ray tomography and finite element modeling10.1016/j.matdes.2017.02.009 ↗
39. Preparation and compressive performance of an A356 matrix syntactic foam
40. In situ experiments with X ray tomography: an attractive tool for experimental mechanics10.1007/s11340-010-9333-7 ↗
41. Comparison of aluminium foams prepared by different methods using X-ray tomography10.1016/j.matchar.2018.02.015 ↗
42. The temperature effect on the compressive behavior of closed-cell aluminum-alloy foams10.1007/s11665-017-3098-4 ↗
43. Uniaxial stress-strain behaviour of aluminium alloy foams10.1016/S1359-6454(99)00128-7 ↗
44. Deformation characteristics of metal foams10.1023/A:1004383222228 ↗
45. The effect of structural defects on the compressive behavior of closed-cell Al foam10.1016/j.actamat.2005.04.010 ↗