journal article·2025-03

Microwave-assisted in-situ fabrication of copper reinforced with molybdenum and tungsten particles

Khalid Bashir, Dheeraj Gupta, Vivek Jain

Publisher page

Abstract

In this study, Copper-based (Cu) metal matrix composites were successfully fabricated by using a novel microwave hybrid heating (MHH) technique. The copper powder, reinforced with varying proportions of tungsten (5–15 %W) and molybdenum (5–15 %Mo) by weight fraction, was processed in a conventional 900 W maximum power and fixed 2.45 GHz domestic microwave oven. The composite samples were then evaluated for their mechanical and metallurgical properties. The average raw powder particle size used in the casting process had an approximately 30 μm. The various characterizations tools/techniques were performed like, Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), and Vicker`s microhardness testing on the developed composite casts. The microstructural analysis revealed a uniform cellular-like solidification pattern with finely recrystallized grains, representing uniform like reinforcement distribution. X-ray diffraction (XRD) analysis confirmed the presence of intermetallic combinations and typical oxide phases such as Cu 64O and CuWO 4 in Cu W, Cu 6Mo 5O 18, and MoO 2 within the composite matrix. The composite castings exhibited a maximum porosity level of 0.61 ± 0.41 %. The relative density was found 98.71 % increase in Cu + 15 %W within the casting. The Vickers`s microhardness testing revealed that the average microhardness of the Cu + 15 %W composites was 147.23 ± 7.36 HV 0.3, demonstrating a significant improvement in hardness, specifically 2.16 times higher than the microhardness of microwave-processed pure Cu and 1.47 times better than 15 %Mo reinforcement.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Bauxite Residue and Utilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (57)

Show source-provided references
1. Tribological performance of gradient ag-multilayer graphene/TC4 alloy self-lubricating composites prepared by laser additive manufacturing10.1080/10402004.2021.1922789 ↗
2. Improving the tribological properties of AISI M50 steel using Sns/Zno solid lubricants10.1016/j.jallcom.2019.153494 ↗
3. A new M50 matrix composite sintered with a hybrid Sns/Zno nanoscale solid lubricants: an experimental investigation10.1088/2053-1591/ab4675 ↗
4. Studies on the effect of applied load, sliding speed and temperature on the wear behavior of M50 steel reinforced with Al2O3 and / or graphene nanoparticles10.1016/j.jmrt.2021.02.082 ↗
5. Enhanced strength and excellent transport properties of a superaligned carbon nanotubes reinforced copper matrix laminar composite10.1016/j.compositesa.2016.05.027 ↗
6. Interfacial microstructure evolution and weld formation during ultrasonic welding of Al alloy to cu10.1016/j.matchar.2018.03.010 ↗
7. Influence of annealed cu–Al2O3 thin film on the performance of high power LED: thermal and optical analysis10.1007/s11082-016-0454-9 ↗
8. Thermal behavior of silicon-copper micro vapor chamber for high power LEDs10.1007/s11801-016-5264-6 ↗
9. The development of molecular-based materials for electrical and electronic applications10.1007/s11837-015-1355-2 ↗
10. Advanced composite materials for heat sink applications
11. Microstructure and mechanical properties of Al2O3 - WC - co composites obtained by spark plasma sintering
12. Impact of the SiC addition on the morphological, structural and mechanical properties of cu-SiC composite powders prepared by high energy milling10.1016/j.apt.2021.06.006 ↗
13. Thermal performance of high power LED on boron doped Aluminium nitride thin film coated copper substrates10.9734/JSRR/2015/14232 ↗
14. Non-equilibrium copper-based crystalline alloy sheet having ultrahigh strength and good electrical conductivity10.1016/j.jallcom.2011.01.137 ↗
15. Improving the mechanical properties and coefficient of thermal expansion of molybdenum-reinforced copper using powder metallurgy10.1088/2053-1591/ac209a ↗
16. Activated liquid phase sintering of W-cu and Mo-cu10.1016/j.ijrmhm.2015.04.030 ↗
17. Huber · Materialia · 2020 · 9
18. Cold gas dynamic spraying of a novel micro-alloyed copper: microstructure, mechanical properties10.1016/j.jallcom.2016.06.037 ↗
19. Effect of ball-milling and graphene contents on the mechanical properties and fracture mechanisms of graphene nanosheets reinforced copper matrix composites10.1016/j.jallcom.2016.08.303 ↗
20. Effects of Zn additions on the solid-state sintering of W-cu composites10.1016/j.matdes.2011.10.006 ↗
21. A new method to investigate the sliding wear behaviour of materials based on energy dissipation: W-25wt%Cu composite10.1016/j.wear.2011.08.023 ↗
22. Optimized thermal properties in diamond particles reinforced copper-titanium matrix composites produced by gas pressure infiltration10.1016/j.compositesa.2016.10.005 ↗
23. Copper–nickel-based diamond cutting tools: stone cutting evaluation10.1007/s00170-017-0220-6 ↗
24. Microstructure and properties of rare earth-containing Cu-Cr-Zr alloy10.1016/S1003-6326(15)63717-7 ↗
25. Achieving higher strength in Cu–Ag–Zr alloy by warm/hot rolling10.1007/s12598-015-0502-9 ↗
26. Synthesis and tribological properties of copper-alumina nanocomposites prepared by coprecipitation technique10.1007/s11595-016-1500-y ↗
27. Evaluation of mechanical and Tribological behavior of Al–4 %Cu–x %SiC composites prepared through powder metallurgy technique10.1007/s12666-016-0923-7 ↗
28. High-volume-fraction Cu/Al2O3–SiC hybrid interpenetrating phase composite10.1007/s00339-015-9392-9 ↗
29. Effect of graphite and SiC addition into Cu and SiC particle size effect on fabrication of Cu–graphite–SiC MMC by powder metallurgy10.1007/s12666-016-1026-1 ↗
30. Cross-property connections for copper–graphite composites10.1007/s00707-015-1411-6 ↗
31. High temperature deformation behavior of a stainless steel fiber-reinforced copper matrix composite10.1016/j.msea.2016.03.084 ↗
32. A nanostructured Ni/graphene hybrid for enhanced electrochemical hydrogen storage10.1016/j.jallcom.2014.04.206 ↗
33. Numerical simulation of temperature field distribution for laser sintering graphene reinforced nickel matrix nanocomposites10.1016/j.jallcom.2016.07.022 ↗
34. Mechanical alloying of the immiscible Cu-60wt%Cr alloy: phase transitions, microstructure, and thermodynamic characteristics
35. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
36. Mechanical properties of titanium matrix composites fabricated via powder metallurgy method10.1016/j.matpr.2020.04.569 ↗
37. Mechanical alloying and sintering of nanostructured tungsten carbide-reinforced copper composite and its characterization10.1016/j.matdes.2011.02.025 ↗
38. Supersaturated cu-Li solid solutions produced by mechanical alloying10.1016/j.jallcom.2006.01.032 ↗
39. Effect of sintering temperature on the structure and properties of cerium-doped 0.94(Bi0.5Na0.5)TiO3-0.06BaTiO3 piezoelectric ceramics10.1016/j.jallcom.2007.04.037 ↗
40. Effects of Zr on the amorphization of cu-Ni-Zr alloys prepared by mechanical alloying10.1016/j.jallcom.2018.04.259 ↗
41. Microwave melting and processing of metal–ceramic composite castings10.1177/0954405416666900 ↗
42. Microwave processing of materials and applications in manufacturing industries: a review10.1080/10426914.2014.952028 ↗
43. Full sintering of powdered-metal bodies in a microwave field10.1038/21390 ↗
44. Microwave processing of metallic joints and their characterisation10.26634/jme.1.1.1213 ↗
45. On microstructure and flexural strength of metal-ceramic composite cladding developed through microwave heating10.1016/j.apsusc.2012.02.019 ↗
46. On processing and flexural behaviour of functionally graded clads developed through microwave irradiation10.1088/2053-1591/ab11ea ↗
47. An approach for functionally graded cladding of composite material on austenitic stainless steel substrate through microwave heating10.1177/0021998317705977 ↗
48. On surface modification of austenitic stainless steel using microwave processed Ni/Cr3C2 composite cladding10.1080/02670844.2017.1362808 ↗
49. Development of copper alloy by microwave hybrid heating technique and its characterization10.18280/ijht.360425 ↗
50. A sustainable and energy efficient approach for development of electrically conductive materials and their characterizations
51. Metrology · 2021
52. Microstructural investigation of variable tungsten reinforcement in copper-based composite microwave castings
53. Cavitation erosion behavior of microwave-processed Ni–40Cr3C2 composite clads: a parametric investigation using ultrasonic apparatus
54. Enhancing microstructural properties of copper-based composite castings through microwave-assisted reinforcement with MWCNT
55. Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: an experimental investigation on mechanical and tribological performances
56. Experimental study of microstructure, mechanical and tribological properties of cBN particulates SS316 alloy based MMCs fabricated by DMLS technique10.1007/s12206-017-0516-3 ↗
57. Processing and characterization of SS316 based metal matrix composite casting through microwave hybrid heating10.1177/09544062221104443 ↗