journal article·2021-01

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

Yinghui Zhou, Xin Lin, Nan Kang, Weidong Huang, Zhennan Wang

Publisher page

Abstract

Abstract The dense 2219 Al alloy was successfully fabricated by the Wire + Arc additive manufacturing (WAAM) technology. It was subsequently processed through solution and aging (T6) heat treatment to improve its performance. There were some θ' phase precipitated because of the thermal cycling during the WAAM forming process. Then, the supersaturation of copper in the α-Al matrix was reduced. The influence of solution temperature on the precipitation behavior of the θ″ phase and the microstructure evolution were investigated in detail. The experimental and calculative results demonstrate that the precipitation strengthening of the θ″ phase improves with the increasing solution temperature, and the strengthening contribution of θ″ phase is 202.1 MPa, 165.2 MPa, and 150.3 MPa corresponding to the solution temperature at 540 °C, 530 °C, and 520 °C, respectively. The average ultimate tensile strength, yield strength, elongation, and micro-hardness of the WAAM processed samples were obtained after T6 treatment with 540 °C, 45 min/Water quenching +180 °C, 6 h/Water quenching, which is 397 ± 4 MPa, 303 ± 5 MPa, 5.3 ± 1%, and 139 ± 6 HV respectively. Compared to the casting + T6 treated 2219 Al alloy, the samples in this research present a similar tensile strength and slightly lower ductility.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Microstructural evolution of Al2Cu phase and mechanical properties of the large-scale Al alloy components under different consecutive manufacturing processes10.1016/j.jallcom.2019.07.346 ↗
2. Improvement of high temperature strength of 2219 alloy by Sc and Zr addition through a novel three-stage heat treatment route10.1016/j.msea.2018.07.003 ↗
3. Multi-response optimization of process parameters for MIG welding of AA2219-T87 by Taguchi Grey relational analysis
4. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
5. Microstructures and mechanical properties of laser additive manufactured Al-5Si-1Cu-mg alloy with different layer thicknesses10.1016/j.jallcom.2019.03.101 ↗
6. Microstructure and mechanical properties of a heat-treatable Al-3.5Cu-1.5Mg-1Si alloy produced by selective laser melting10.1016/j.msea.2017.11.063 ↗
7. Aging behavior of high-strength Al alloy 2618 produced by selective laser melting10.1007/s11661-016-3883-y ↗
8. Wire + arc additive manufacturing10.1179/1743284715Y.0000000073 ↗
9. A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement10.1016/j.jmapro.2018.08.001 ↗
10. Workpiece vibration augmented wire arc additive manufacturing of high strength aluminum alloy10.1016/j.jmatprotec.2019.03.028 ↗
11. The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 231910.1016/j.jmatprotec.2018.07.030 ↗
12. Optimization of wire feed for GTAW based additive manufacturing10.1016/j.jmatprotec.2016.11.027 ↗
13. Mechanical properties and fracture behaviors of GTA-additive manufactured 2219-Al after an especial heat treatment10.1007/s11665-017-2627-5 ↗
14. Strengthening mechanism in laser-welded 2219 aluminium alloy under the cooperative effects of aging treatment and pulsed electromagnetic loadings10.1016/j.msea.2017.12.081 ↗
15. The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy10.1016/j.msea.2015.10.101 ↗
16. Mechanical Properties and Fracture Behaviors of GTA-Additive Manufactured 2219-Al After an Especial Heat Treatment10.1007/s11665-017-2627-5 ↗
17. Multiple precipitation reactions and formation of θ’-phase in a pre-deformed Al–Cu alloy10.1016/j.msea.2018.07.039 ↗
18. A coupled EBSD/TEM study on the interfacial structure of Al/Mg/Al laminates10.1016/j.jallcom.2018.11.366 ↗
19. Precipitation behavior of aluminum alloy 2139 fabricated using additive manufacturing10.1016/j.msea.2015.08.088 ↗
20. Mao · 2020
21. Plate-like precipitate effects on plasticity of Al-Cu alloys at micrometer to sub-micrometer scales10.1016/j.matdes.2019.108444 ↗
22. Effects of thermomechanical treatment on grain refinement, second-phase particle dissolution, and mechanical properties of 2219 Al alloy10.1016/j.jmatprotec.2019.116506 ↗
23. Structure and energetics of the coherent interface between the θ’ precipitate phase and aluminium in Al–Cu10.1016/j.actamat.2011.07.059 ↗
24. Thermal modeling and characterization of wire arc additive manufactured duplex stainless steel10.1016/j.jmatprotec.2019.05.003 ↗
25. Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy10.1016/j.jmst.2019.06.016 ↗
26. Influence of pre-deformation and subsequent ageing on the hardening behavior and microstructure of 2219 aluminum alloy forgings10.1016/j.jallcom.2016.06.111 ↗
27. Stress-level-dependency and bimodal precipitation behaviors during creep ageing of Al-Cu alloy: experiments and modeling10.1016/j.ijplas.2018.07.001 ↗
28. Thermodynamic assessment of the Al–Cu–Zn system, part II: Al–cu binary system10.1016/j.calphad.2015.10.004 ↗
29. Effects of cold predeformation on dissolution of second-phase Al2Cu particles during solution treatment of 2219 Al-cu alloy forgings10.1016/j.matchar.2017.10.026 ↗
30. Strengthening effect of unshearable particles of finite size: A computer experimental study10.1016/S1359-6454(99)00179-2 ↗
31. A Model for Precipitation Kinetics and Strengthening in Al-Cu-Mg Alloys10.1016/j.msea.2007.03.033 ↗
32. The influence of laves phases on the room temperature tensile properties of Inconel 718 fabricated by powder feeding laser additive manufacturing10.1016/j.actamat.2018.10.032 ↗