journal article·2023-03

Quasi-in-situ analysis of adhesion failure at reduced iron/substrate interface of advanced high strength steel

Xinyan Jin, Guangxin Wu

Publisher page

Abstract

Oxidation-reduction process is an effective way to improve the galvanizability of advanced high strength steel (AHSS). However, the adhesion failure occurred at the reduced iron/substrate interface may degrade the coating quality. To figure out the failure mechanism of reduced iron/steel interface of AHSS, a quasi-in-situ analysis of adhesion failure at reduced iron/steel interface was performed by means of dual beam focused ion beam - scanning electron microscope (FIB-SEM) and transmission electron microscope (TEM), and the interface energies of different interfaces were studied by first-principles calculations. TEM observations show that the interface bonding strength of the reduced iron/substrate interface is weakened by the predominant formation of continuous Mn and Si external oxides at the interface. The first-principles calculation results predicts that the SiO 2 /(011)Fe interface is the most unstable and prone to cracking based on its relatively the highest interface binding energy among all the considered interfaces. While the real crack was observed to initiate and propagate inside the lower amorphous SiO 2 layer instead of along the SiO 2 /Fe interface. It is considered that the defects in the actual interface oxides layer, especially the existence of a large number of pores in SiO 2, which eventually leads to cracking starting point.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Advanced high strength steels (AHSS) for automotive applications− tailored properties by smart microstructural adjustments[J]10.1002/srin.201700210 ↗
2. Third generation of advanced high-strength steels: processing routes and properties[J]
3. Tisza · 2020 · 81
4. The metallurgy of zinc-coated steel[J]10.1016/S0079-6425(98)00006-1 ↗
5. Importance of Si/Mn ratio on galvanizability of next generation advanced high strength steels[C]
6. Effect of Sn addition, process atmosphere pO2, and annealing time on the selective oxidation of a C-2Mn-1.7 Si (Wt Pct) advanced high-strength steel during continuous galvanizing[J]10.1007/s11661-019-05202-3 ↗
7. Effect of Mn and Cr on the selective oxidation, surface segregation and hot-dip Zn coatability[J]10.1016/j.surfcoat.2019.124908 ↗
8. On the reactive wetting of a medium-Mn advanced high-strength steel during continuous galvanizing[J]10.1016/j.surfcoat.2018.10.028 ↗
9. Effect of water pressure and soaking time on the selective oxidation of DP980 advanced high strength steel[J]10.1016/j.apsusc.2018.05.034 ↗
10. Improvement of the galvanized coating quality of high strength dual phase steels by pre-electroplating nickel layer[J]10.1002/srin.201000124 ↗
11. Role of dew points and Fe pre-coats on the galvanizing and galvannealing of dual phase steel[J]10.1016/j.surfcoat.2021.127573 ↗
12. Microstructural investigation of galvanized coatings with prior flash coating of copper on DP steels[J]10.1016/j.surfcoat.2015.11.043 ↗
13. Wetting behavior of Zn-Al liquid on Si-containing steel after surface oxidation and reduction treatment[J]10.1007/s11663-020-01782-3 ↗
14. Use of pre-oxidation to improve reactive wetting of high manganese alloyed steel during hot-dip galvanizing[J]10.1016/j.surfcoat.2011.07.088 ↗
15. Industrial use of preoxidation during continuous hot-dip coating of (high) alloyed steels[C]
16. Quality improvement of the galvanized strips by the oxidation/reduction process[J]
17. Influence of Fe oxidation on selective oxidation behavior of Si and Mn added in high strength sheet steel[J]10.2355/isijinternational.54.664 ↗
18. Effects of oxygen partial pressure on oxidation behavior of CMnSi TRIP steel in an oxidation-reduction scheme[J]10.14773/cst.2017.16.1.15 ↗
19. Changes and challenges of using preoxidation in hot dip galvanizing of AHSS[C]
20. Pre-oxidation of advanced high strength steels: influence of temperature, reaction time and oxygen concentration on oxide thicknesses[C]
21. Characterization of surface layers of oxidation-reduction treated Si and Mn added advanced high strength steel[J]10.1016/j.surfcoat.2019.125172 ↗
22. Investigation on the coating adhesion of galvanized AHSS treated by oxidation-reduction process[J]
23. First-principles simulation: ideas, illustrations and the CASTEP code[J]10.1088/0953-8984/14/11/301 ↗
24. Generalized gradient approximation made simple[J]10.1103/PhysRevLett.77.3865 ↗
25. Special points for Brillouin-zone integrations[J]10.1103/PhysRevB.13.5188 ↗
26. 2022
27. 2022
28. 2022
29. 2022
30. Effect of water pressure and soaking time on the selective oxidation of DP980 advanced high strength steel[J]10.1016/j.apsusc.2018.05.034 ↗
31. Influence of the oxidation-reduction process on the surface and sub-surface microstructure of Intercritically annealed CMnSi TRIP steel[J]10.2355/isijinternational.51.630 ↗
32. Selective oxidation of ternary Fe-Mn-Si alloys during annealing process[J]10.1016/j.corsci.2020.108859 ↗
33. Formation of surface and subsurface oxides during ferritic, intercritical and austenitic annealing of CMnSi TRIP steel[J]10.2355/isijinternational.48.1745 ↗
34. Study of selective oxidation behavior of a 1.2 Si-1.5 Mn TRIP steel during intercritical annealing[J]10.1149/2.050212jes ↗
35. Suppression of liquid-metal-embrittlement by twin-induced grain boundary engineering approach[J]10.1016/j.mtla.2020.100668 ↗
36. Relation between microstructure and adhesion of hot dip galvanized zinc coatings on dual phase steel[J]10.1016/j.actamat.2012.02.003 ↗
37. Mechanical properties of α-SiO2 crystal based on molecular dynamics[J]
38. Pathway to understand liquid metal embrittlement (LME) in Fe-Zn couple: from fundamentals toward application[J]10.1016/j.pmatsci.2021.100798 ↗
39. Effect of Ni doping on the embrittlement of liquid zinc at Σ5 Fe austenite grain boundary[J]10.3390/met12010027 ↗
40. Investigating AlSi coating fracture at high temperatures using acoustic emission sensors[J]10.1016/j.surfcoat.2021.127587 ↗
41. Sun · 2012
42. Influence of pores on crack initiation in monotonic tensile and cyclic loadings in lost foam casting A319 alloy by using 3D in-situ analysis[J]10.1016/j.msea.2016.07.036 ↗
43. Crack propagation behavior of die-cast AlSiMgMn alloys with in-situ SEM observation and finite element simulation[J]10.1016/j.mtcomm.2019.01.009 ↗
44. Selective oxidation of TWIP steel during continuous annealing[J]10.1002/srin.201100296 ↗
45. Interface fracture behavior of zinc coatings on steel: experiments and finite element calculations[J]10.1016/j.surfcoat.2006.08.046 ↗