journal article·2018-03

Influence of annealing temperature on microstructure and tensile property of cold-rolled Fe-0.2C-11Mn-6Al steel

Z.H. Cai, H.Y. Li, S.Y. Jing, Z.C. Li, H. Ding, Z.Y. Tang, R.D.K. Misra

Publisher page

Abstract

Abstract To fully realize the potential of austenite characterized by strip-like and equiaxed structure and enhance the comprehensive mechanical properties of medium-Mn steel, the as-hot-rolled Fe-0.2C-11Mn-6Al steel was subjected to cold roll annealing to refine the grain size. The ultimate tensile strength of the cold-rolled steel annealed at 650 °C was significantly enhanced, while the total elongation was markedly decreased. The variation in tensile properties of the annealed cold-rolled steel was due to weakening of transformation induced plasticity (TRIP) effect and enhanced twinning induced plasticity (TWIP) effect with increase in quenching temperature. Furthermore, austenite had two different morphologies, strip-like and granular. Though the grain size of granular austenite increased with increased annealing temperature, the austenite stability increased with increase in quenching temperature, which is contrary to the expectations. This is attributed to refinement of large austenite strips induced by recrystallization.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Experimental and numerical analysis on formation of stable austenite during the intercritical annealing of 5Mn steel10.1016/j.actamat.2011.03.025 ↗
2. Low-carbon manganese TRIP steels10.4028/www.scientific.net/MSF.539-543.4327 ↗
3. Enhanced work-hardening behaviors and mechanical properties in ultrafine-grained steels with large-fractioned metastable austenite10.1016/j.scriptamat.2010.06.023 ↗
4. Austenite stability of ultrafine-grained transformation-induced plasticity steel with Mn partitioning10.1016/j.scriptamat.2011.04.010 ↗
5. Fe–Al–Mn–C lightweight structural alloys: a review on the microstructures and mechanical properties10.1088/1468-6996/14/1/014205 ↗
6. Element partitioning effect on microstructure and mechanical property of the micro-laminated Fe–Mn–Al–C dual phase steel10.1016/j.msea.2015.12.029 ↗
7. Mechanical properties and austenite stability in hot-rolled 0.2C–1.6/3.2Al–6Mn–Fe TRIP steel10.1016/j.msea.2015.05.061 ↗
8. Influence of Al on the microstructural evolution and mechanical behavior of low-carbon, manganese transformation-induced-plasticity steel10.1007/s11661-009-0124-7 ↗
9. Microstructure and tensile behavior of duplex low-density steel containing 5 mass% aluminum10.1016/j.scriptamat.2012.09.030 ↗
10. Mechanistic contribution of the interplay between microstructure and plastic deformation in hot-rolled Fe–11Mn–2/4Al–0.2C steel10.1016/j.msea.2015.11.084 ↗
11. Microstructural evolution and mechanical properties of hot-rolled 11% manganese TRIP steel10.1016/j.msea.2012.09.083 ↗
12. Microstructure and deformation behavior of the hot-rolled medium manganese steels with varying aluminum-content10.1016/j.msea.2016.08.119 ↗
13. A model for the microstructure of some advanced bainitic steels10.2320/matertrans1989.32.689 ↗
14. Effect of grain size on strain-induced martensitic transformation start temperature in an ultrafine grained metastable austenitic steel10.1007/s12540-011-0804-x ↗
15. Bainite in silicon steels: new composition–property approach. Part 110.1179/030634583790420600 ↗
16. Effect of microstructure on retained austenite stability and work hardening of TRIP steels10.1016/j.msea.2011.02.032 ↗
17. Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content10.1016/j.actamat.2014.10.052 ↗
18. Work hardening behavior of ultrafine-grained Mn transformation-induced plasticity steel10.1016/j.actamat.2011.08.030 ↗
19. Microstructural and mechanical characterization of C–Mn–Al–Si cold-rolled TRIP-aided steel10.1016/j.msea.2006.09.101 ↗
20. Effect of isothermal bainitic transformation temperature on retained austenite fraction in C-Mn-Si-Al-Nb-Ti TRIP-type steel
21. Effect of austenite grain size on martensitic transformation of a low alloy steel10.4028/www.scientific.net/MSF.475-479.3169 ↗
22. Evaluation of intragranular misorientation parameters measured by EBSD in a hot worked austenitic stainless steel10.1111/j.1365-2818.2007.01850.x ↗
23. Microstructure, texture and mechanical properties of friction stir welded butt joints of 2A97 Al Li alloy ultra-thin sheets10.1016/j.jallcom.2016.08.330 ↗
24. Steel-based composites: driving forces and classifications10.1146/annurev-matsci-070909-104438 ↗
25. A model for strain-induced martensitic transformation of TRIP steel with strain rate10.1016/j.commatsci.2006.11.006 ↗
26. Annealing temperature dependence of the tensile behavior of 10 pct Mn multi-phase TWIP-TRIP steel10.1007/s11661-014-2540-6 ↗
27. The respective hardening contributions of dislocations and twins to the flow stress of a twinning-induced plasticity steel10.1016/j.scriptamat.2015.09.003 ↗
28. Measurement of microstructural parameters of nanocrystalline Fe–30 wt.% Ni alloy produced by surface mechanical attrition treatment10.1016/j.jallcom.2008.06.136 ↗
29. Comparison of dislocation densities of primary and secondary recrystallization grains of Si-Fe10.1016/0001-6160(57)90122-0 ↗
30. The estimation of dislocation densities in metals from X-ray data10.1016/0001-6160(53)90106-0 ↗
31. Tensile properties and twinning behavior of high manganese austenitic steel with fine-grained structure10.1016/j.scriptamat.2008.06.050 ↗
32. The effect of grain size on the twin initiation stress in a TWIP steel10.1016/j.actamat.2015.02.008 ↗