Enhancement of mechanical and wear properties in laser powder bed fusion fabricated Ti-15Zr alloys by oxygen content regulation
Source abstract
Abstract
Ti-15Zr-xO alloys (x = 0.2-0.5 wt.%) with non-toxic and biocompatibility were fabricated by laser powder bed fusion (LPBF). All as-built samples were α-hcp dominated. Increasing O content progressively intensified the texture and promoted preferential growth of selected α variants. The hierarchical lath architecture evolved from a lamella-dominated morphology toward a lamellar-cellular transitional structure, accompanied by hierarchical lath subdivision and the development of a more continuous low-angle boundary network. In addition, a small fraction of nanoscale crystalline regions was also observed in the vicinity of some grain boundaries. With increasing O content, hardness and strength increased whereas ductility decreased markedly. The strength increase is governed primarily by interstitial oxygen solid-solution strengthening, with secondary contributions from lath-domain refinement and TiO₂-assisted pinning of dislocations and interfaces. The reduction in uniform plasticity is mainly ascribed to intensified texture strengthening and microstructural coarsening. With increasing O content, wear resistance improved markedly, with a minimum wear rate of 3.80 × 10⁻⁴ mm³·N⁻¹·m⁻¹, attributed to enhanced hardness and resistance to plastic deformation, together with the protective role of fine in situ Ti-O-rich third-body particulates, accompanied by a shift from abrasive to oxidation-controlled wear.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Additive Manufacturing Materials and Processes · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (66)
Show source-provided references
1. Titanium alloys in total joint replacement—a materials science perspective10.1016/S0142-9612(97)00146-4 ↗
2. Ti based biomaterials, the ultimate choice for orthopaedic implants - a review10.1016/j.pmatsci.2008.06.004 ↗
3. A review—metastable β titanium alloy for biomedical applications10.1186/s44147-023-00196-7 ↗
4. Vanadium ionic species from degradation of Ti-6Al-4V metallic implants: in vitro cytotoxicity and speciation evaluation10.1016/j.msec.2018.11.090 ↗
5. Towards load-bearing biomedical titanium-based alloys: from essential requirements to future developments10.1016/j.pmatsci.2024.101277 ↗
6. Quantitative strengthening evaluation of powder metallurgy Ti-Zr binary alloys with high strength and ductility10.1016/j.jallcom.2020.156954 ↗
7. Local lattice distortions and the structural instabilities in bcc Nb-Ta-Ti-Hf high-entropy alloys: An ab initio computational study10.1016/j.actamat.2023.119415 ↗
8. Interplay between dislocation glide and ω precipitation in a Ti-15Mo alloy investigated by TEM10.1016/j.msea.2023.144855 ↗
9. Prediction of tribocorrosion processes in titanium-based dental implants using acoustic emission technique: initial outcome10.1016/j.msec.2021.112000 ↗
10. Effect of acidic fluoride solution on the corrosion resistance of ZrTi alloys for dental implant application10.1016/j.corsci.2014.06.042 ↗
11. Cytocompatibility of Ti-xZr alloys as dental implant materials10.1007/s10856-021-06522-w ↗
12. Fatigue behavior of Ti50Zr alloy for dental implant application10.1016/j.jallcom.2019.04.165 ↗
13. Microstructure and mechanical properties of Ti-15Zr alloy used as dental implant material10.1016/j.jmbbm.2016.05.008 ↗
14. Light element strategies in titanium: from atomic-scale solution to composite reinforcement10.1016/j.pmatsci.2025.101637 ↗
15. A high-oxygen strategy for strength-ductility synergy in powder metallurgy pure titanium via controlled TiO2 addition
16. The effects of interstitial oxygen on mechanical properties of TiZrNb medium-entropy alloy over a wide temperature range10.1016/j.jallcom.2024.174394 ↗
17. Oxygen-mediated high uniform plasticity in α-β titanium alloys10.1038/s41467-025-65851-4 ↗
18. Grain refinement in titanium prevents low temperature oxygen embrittlement10.1038/s41467-023-36030-0 ↗
19. Oxygen-dislocation interaction-mediated nanotwinned nanomartensites in ultra-strong and ductile titanium alloys10.1016/j.mattod.2024.04.003 ↗
20. Trifunctional local-range order oxygen structure enhanced strength-ductility and fatigue resistance in large-scale metastable titanium alloy10.1038/s41467-025-62646-5 ↗
21. Mechanical property enhancement of high-plasticity powder metallurgy titanium with a high oxygen concentration10.1016/j.jallcom.2021.161006 ↗
22. Wear transition of solid-solution-strengthened Ti-29Nb-13Ta-4.6Zr alloys by interstitial oxygen for biomedical applications10.1016/j.jmbbm.2015.07.001 ↗
23. Recent advances in metal additive manufacturing from a tribological perspective10.1016/j.jallcom.2025.185613 ↗
24. Recent advance in laser powder bed fusion of Ti-6Al-4V alloys: microstructure, mechanical properties and machinability10.1080/17452759.2024.2446952 ↗
25. Novel tensile deformation mode in laser powder bed fusion prepared Ti-O alloy10.1016/j.msea.2023.146057 ↗
26. Tensile property enhancement by oxygen solutes in selectively laser melted titanium materials fabricated from pre-mixed pure Ti and TiO2 powder10.1016/j.msea.2020.139983 ↗
27. Microstructure and enhanced strength and ductility of Ti-Zr-O alloys prepared by a laser powder bed fusion process
28. Selective laser melting produced Ti-6Al-4V: post-process heat treatments to achieve superior tensile properties10.3390/ma11010146 ↗
29. Formation and control of martensite in Ti-6Al-4V alloy produced by selective laser melting10.1016/j.matdes.2016.06.117 ↗
30. The effects of oxygen addition on microstructure and mechanical properties of Ti-Mo alloys for biomedical application10.3389/fbioe.2024.1380503 ↗
31. X-ray diffraction profile analysis of martensitic Ti6Al4V (ELI) parts produced by laser powder bed fusion10.1051/matecconf/202338810003 ↗
32. Surface chemical state of Ti powders and its alloys: effect of storage conditions and alloy composition10.1016/j.apsusc.2016.01.046 ↗
33. Strong and ductile titanium-oxygen-iron alloys by additive manufacturing10.1038/s41586-023-05952-6 ↗
34. Mechanical spectroscopy of interface stress relaxation in metal-matrix composites10.1016/j.msea.2006.03.129 ↗
35. Interactions between dislocations and boundaries during deformation10.3390/ma14041012 ↗
36. Direct diffusion through interpenetrating networks: oxygen in titanium10.1103/PhysRevLett.107.045504 ↗
37. Possible globularization mechanism in LPBF additively manufactured Ti-6Al-4 V alloys10.1016/j.matchar.2023.113303 ↗
38. Grain boundary α-phase precipitation and coarsening: comparing laser powder bed fusion with as-cast Ti-6Al-4V10.1016/j.scriptamat.2021.114261 ↗
39. Facile manipulation of mechanical properties of Ti-6Al-4V through composition tailoring in laser powder bed fusion10.1016/j.jallcom.2023.169022 ↗
40. Effects of process parameters and scan strategy on the microstructure and density of stainless steel 316 L produced via laser powder bed fusion
41. An improved combination of tensile strength and ductility in titanium alloys via oxygen ordering10.1016/j.msea.2023.144720 ↗
42. Oxygen interstitials make metastable β titanium alloys strong and ductile10.1016/j.actamat.2023.119165 ↗
43. Microstructure evolution and mechanical properties of Ti-O alloy fabricated via laser powder bed fusion (L-PBF)
44. Laser powder bed fusion of GH3536 nickel-based superalloys: processing parameters, microstructure and mechanical properties10.1016/j.matchar.2023.113018 ↗
45. Dependency of recrystallization kinetics on the solidification microstructure of 316L stainless steel processed by laser powder bed fusion (LPBF)10.1016/j.matchar.2022.112370 ↗
46. Thermal cycle induced solid-state phase evolution in IN718 during additive manufacturing: a physical simulation study10.1016/j.jallcom.2023.173181 ↗
47. Tailoring TA2 titanium alloy with oxygen microalloying for enhanced mechanical performance in nuclear fuel reprocessing10.1016/j.msea.2025.149359 ↗
48. Effect of oxygen content on thermal stability of grain size for nanocrystalline Fe10Cr and Fe14Cr4Hf alloy powders10.1016/j.jallcom.2017.05.261 ↗
49. Experimental assessment of variant selection rules for grain boundary α in titanium alloys10.1016/j.actamat.2015.09.021 ↗
50. 3D electron backscatter diffraction study of α lath morphology in additively manufactured Ti-6Al-4V10.1016/j.ultramic.2020.113073 ↗
51. Recrystallization mechanisms and microstructure development in emerging metallic materials: a review
52. Hot deformation mechanisms in ELI grade Ti-6a1-4V10.1016/S1359-6462(99)00163-3 ↗
53. Variant selection and intervariant crystallographic planes distribution in martensite in a Ti-6Al-4V alloy10.1016/j.actamat.2014.06.064 ↗
54. Physical metallurgy of Ti-Ni-based shape memory alloys10.1016/j.pmatsci.2004.10.001 ↗
55. Effect of oxygen addition on microstructures and mechanical properties of Ti-7.5Mo alloy10.1016/j.jallcom.2017.12.072 ↗
56. Effects of degree of deformation on the microstructure, mechanical properties and texture of hybrid-reinforced titanium matrix composites10.1016/j.actamat.2012.01.032 ↗
57. Influence of lowering basal stacking fault energy on twinning behaviours10.1016/j.actamat.2022.118637 ↗
58. Dynamic recrystallization of Ti-6Al-2Zr-1Mo-1V in β forging process10.1016/S1003-6326(11)61242-9 ↗
59. Dynamic recrystallization in a near β titanium alloy under different deformation modes - transition and correlation10.1016/j.actamat.2024.120148 ↗
60. Variation of work hardening rate by oxygen contents in pure titanium alloy10.1016/j.msea.2015.02.074 ↗
61. Yielding nature and hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures10.1016/j.scriptamat.2019.07.015 ↗
62. Exploring the limits of mechanical properties of Ti-Zr binary alloys10.1016/j.matlet.2022.132091 ↗
63. Assessment of hydrogen embrittlement via image-based techniques in Al-Zn-Mg-Cu aluminum alloys10.1016/j.actamat.2019.06.056 ↗
64. Mechanisms of fatigue crack propagation in metals, ceramics and composites: role of crack tip shielding10.1016/0025-5416(88)90547-2 ↗
65. In situ TEM observations of dislocation dynamics in α titanium: effect of the oxygen content10.1016/j.msea.2017.07.040 ↗
66. Contact and rubbing of flat surfaces10.1063/1.1721448 ↗