Comparative assessment of gas and water atomized powders for additive manufacturing of 316 L stainless steel: Microstructure, mechanical properties, and corrosion resistance
Source abstract
Abstract
In this study, the microstructure, and mechanical properties of 316 L stainless steel (SS316L) produced by laser powder bed fusion (LPBF) using water-atomized (WA) and gas-atomized (GA) powders were compared. The results showed that the use of WA powder, with a finer average particle size and better spreadability, led to significantly higher values of tensile strength (UTS), yield strength (YS), elongation (El%), and toughness in the WA samples (728 MPa, 580 MPa, 31.8%, and 215 J/m 3 , respectively) compared to the GA sample (602 MPa, 503 MPa, 25.2%, 145 J/m 3 , respectively). The WA samples also exhibited a non-uniform hardness distribution and superior work-hardening rate due to the presence of multiple inclusions that tightly bound to the matrix and created stress fields, increasing the required energy for dislocation motion . The higher solidification rate of melt pools in the WA sample left more intensive residual stress with distorted grains, exhibiting a higher grain orientation spread (GOS). Additionally, a multitude of geometrically necessary dislocations (GNDs) formed around the boundaries of elongated grains with tilted boundaries to maintain lattice continuity, resulting in a higher kernel average misorientation (KAM) and congestion of low-angle grain boundaries (LAGBs), particularly in the WA sample. XRD patterns confirmed the higher lattice distortion in the WA sample, and the smaller cellular structures observed in SEM images were consistent with the higher dislocation density observed in the WA specimens. Finally, the WA sample exhibited lower surface roughness and rather higher resistance to corrosive media containing chlorides.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Additive manufacturing of nano-oxide decorated AlSi10Mg composites: a comparative study on Gd2O3 and Er2O3 additions
2. Effect of particle size distribution on the packing of powder beds: a critical discussion relevant to additive manufacturing
3. In situ alloying of AlSi10Mg-5 wt% Ni through laser powder bed fusion and subsequent heat treatment10.1016/j.jallcom.2022.164081 ↗
4. Solidification pattern, microstructure and texture development in laser powder bed fusion (LPBF) of Al10SiMg alloy10.1016/j.matchar.2018.08.025 ↗
5. Measurement of powder characteristics and quality for additive manufacturing in aerospace alloys
6. Treatment of ferrous melts for the improvement of the sphericity of water atomized powders10.1016/j.matdes.2016.12.059 ↗
7. Effect of input powder attributes on optimized processing and as-built tensile properties in laser powder bed fusion of AlSi10Mg alloy10.1016/j.jmapro.2021.02.024 ↗
8. Effects of powder characteristics on selective laser melting of 316L stainless steel powder
9. Atomization processes of metal powders for 3D printing
10. A comparative study of water and gas atomized low alloy steel powders for additive manufacturing10.1016/j.addma.2020.101675 ↗
11. On the recycling of water atomized powder and the effects on properties of L-PBF processed 4130 low-alloy steel10.3390/ma15010336 ↗
12. Binding mechanisms in selective laser sintering and selective laser melting10.1108/13552540510573365 ↗
13. Fabrication of NiTi through additive manufacturing: a review10.1016/j.pmatsci.2016.08.001 ↗
14. Effect of powder characteristics on production of oxide dispersion strengthened Fe14Cr steel by laser powder bed fusion10.1016/j.powtec.2019.11.022 ↗
15. Selective laser sintering/melting (SLS/SLM) of pure Al, Al–Mg, and Al–Si powders: effect of processing conditions and powder properties10.1016/j.jmatprotec.2013.03.009 ↗
16. Selective laser melting of pure Zn with high density for biodegradable implant manufacturing
17. Metal powders in additive manufacturing: a review on reusability and recyclability of common titanium, nickel and aluminum alloys10.1016/j.addma.2021.102017 ↗
18. Microstructural evolution and mechanical properties of differently heat-treated binder jet printed samples from gas-and water-atomized alloy 625 powders10.1016/j.actamat.2016.11.021 ↗
19. Processability of different IN738LC powder batches by selective laser melting10.1016/j.jmatprotec.2015.09.046 ↗
20. Additive manufacturing of high entropy alloys: a practical review10.1016/j.jmst.2020.11.029 ↗
21. Additive manufacturing of metals10.1016/j.actamat.2016.07.019 ↗
22. J. Schrage, J.H. Schleifenbaum, M. Manfi, Influence of Powder Application Parameters on Powder Bed Properties and on Productivity of Laser Powder Bed Fusion (L-PBF), Proceedings of the 4th Metal Additive Manufacturing Conference, Orebro, Sweden. pp. 25-27. 2019.
23. Spheroidisation of stainless steel powder for additive manufacturing10.3390/met11071081 ↗
24. Spheroidization behavior of water-atomized 316 stainless steel powder by inductively-coupled thermal plasma
25. A review on binder jet additive manufacturing of 316L stainless steel
26. Effects of atomizing media and post processing on mechanical properties of 17-4 PH stainless steel manufactured via selective laser melting10.1016/j.addma.2018.05.011 ↗
27. The influence of particle shape, powder Flowability, and powder layer density on part density in laser powder bed fusion10.3390/met11030418 ↗
28. Influence of the atomization medium on the properties of stainless steel SLM parts10.1016/j.addma.2020.101509 ↗
29. Comparison of the master sinter curves of water-and gas-atomized AISI 4340 low-alloy steel in binder jetting additive manufacturing10.1016/j.addma.2021.102381 ↗
30. Laser-based additive manufacturing technologies for aerospace applications10.1002/adem.201900617 ↗
31. In-situ characterization of laser-powder interaction and cooling rates through high-speed imaging of powder bed fusion additive manufacturing10.1016/j.matdes.2017.09.044 ↗
32. The effects of particle size distribution on the rheological properties of the powder and the mechanical properties of additively manufactured 17-4 PH stainless steel10.1016/j.addma.2021.101851 ↗
33. Effects of particle characteristics on the microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser-powder bed fusion10.1016/j.powtec.2018.03.025 ↗
34. On the effect of rapid annealing on the microstructure and mechanical behavior of additively manufactured stainless steel by laser powder bed fusion10.1016/j.msea.2021.142109 ↗
35. In-situ alloying of stainless steel 316L by co-inoculation of Ti and Mn using LPBF additive manufacturing: microstructural evolution and mechanical properties10.1016/j.msea.2022.144114 ↗
36. Additive manufacturing using water atomized steel powders10.1016/j.mprp.2017.01.004 ↗
37. Direct additive laser manufacturing using gas- and water-atomised H13 tool steel powders10.1007/s00170-003-1844-2 ↗
38. Talako · 2017 · 95
39. Effect of water atomization on properties of type 4130 steel processed by L-PBF10.1016/j.matdes.2021.110085 ↗
40. Ultrafine 316L stainless steel particles with frozen-in magnetic structures characterized by means of electron backscattered diffraction10.1016/j.matlet.2011.04.019 ↗
41. Subgrain microstructural features in directed energy deposited stainless steel 316L: the influence of morphology on mechanical properties10.1016/j.msea.2023.145215 ↗
42. The microstructure, mechanical properties and corrosion resistance of 316L stainless steel fabricated using laser engineered net shaping10.1016/j.msea.2016.09.028 ↗
43. Water atomized 17-4 PH stainless steel powder as a cheaper alternative powder feedstock for selective laser melting10.4028/www.scientific.net/MSF.941.698 ↗
44. Cracking behavior and mechanical properties of austenitic stainless steel parts produced by laser metal deposition10.1016/j.matdes.2012.08.078 ↗
45. An overview of powder granulometry on feedstock and part performance in the selective laser melting process10.1016/j.addma.2017.10.011 ↗
46. 6 - measurement of powder characteristics and quality for additive manufacturing in aerospace alloys
47. Process characteristics and effects of gas- and water-atomized stainless steel powders in laser-based rapid tooling10.2351/1.1585081 ↗
48. Quantitative multiscale correlative microstructure analysis of additive manufacturing of stainless steel 316L processed by selective laser melting10.1016/j.matchar.2019.110074 ↗
49. Rationalization of anisotropic mechanical properties of Al-6061 fabricated using ultrasonic additive manufacturing10.1016/j.actamat.2016.06.048 ↗
50. Additive manufacturing of functionally graded Co–Fe and Ni–Fe magnetic materials10.1016/j.jallcom.2020.153817 ↗
51. A strong, ductile, high-entropy FeCoCrNi alloy with fine grains fabricated via additive manufacturing and a single cold deformation and annealing cycle10.1016/j.addma.2020.101591 ↗
52. Additive manufacturing of three-dimensional (3D)-architected CoCrFeNiMn high-entropy alloy with great energy absorption10.1016/j.scriptamat.2020.08.028 ↗
53. Microstructure and texture evolution in aluminum and commercially pure titanium dissimilar welds fabricated using ultrasonic additive manufacturing10.1016/j.scriptamat.2016.02.013 ↗
54. Morphological and microstructural investigation of the non-planar interface formed in solid-state metal additive manufacturing by additive friction stir deposition10.1016/j.addma.2020.101293 ↗
55. Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting10.1016/j.optlastec.2020.106147 ↗
56. Characterization of steel-ta dissimilar metal builds made using very high power ultrasonic additive manufacturing (VHP-UAM)10.1007/s11661-016-3354-5 ↗
57. Compatibility of deformation in two-phase Ti-Al alloys: dependence on microstructure and orientation relationships10.1007/BF02670762 ↗
58. Investigation of the indentation size effect through the measurement of the geometrically necessary dislocations beneath small indents of different depths using EBSD tomography10.1016/j.actamat.2008.09.039 ↗
59. Assessment of geometrically necessary dislocation levels derived by 3D EBSD10.1016/j.actamat.2015.06.051 ↗
60. On the anisotropy in room-temperature mechanical properties of laser powder bed fusion processed Ti6Al4V-ELI alloy for aerospace applications10.1007/s10853-022-07032-y ↗
61. Rheological properties of gas and water atomized 17-4PH stainless steel MIM feedstocks: effect of powder shape and size10.1016/j.powtec.2017.02.023 ↗
62. The microstructural origin of work hardening stages10.1016/j.actamat.2018.02.002 ↗
63. Effect of atomization on surface oxide composition in 316L stainless steel powders for additive manufacturing10.1002/sia.6846 ↗
64. On the microstructures and fatigue behaviors of 316L stainless steel metal injection molded with gas- and water-atomized powders10.3390/met8110893 ↗
65. In-situ observation of asymmetrical deformation around inclusion in a heterogeneous additively manufactured 316L stainless steel10.1016/j.jmst.2021.02.022 ↗
66. The effect of post-processing heat treatment on the microstructure, residual stress and mechanical properties of selective laser melted 316L stainless steel10.1016/j.msea.2021.141611 ↗
67. Orazem · 2008 · 383