Formation mechanism of the microstructural heterogeneity in a die-cast Al-Mg-Si alloy and its effect on mechanical properties
Source abstract
Abstract
Al-Mg-Si series alloys fabricated by high pressure die casting (HPDC) have a broad application prospect in the production of large-scale and thin-walled die-castings. However, the die-cast Al-Mg-Si series alloys usually exhibit obvious microstructural heterogeneity. This study investigated the microstructural heterogeneity of the die-cast Al-7 Mg-3Si alloy along the thickness direction, and the corresponding formation mechanism was verified. In this study, the die-cast sample can be divided into four distinct regions (R 1 ∼ R 4) from the surface to the center in turn according to the area fraction of the primary α-Al. Two aspects were considered to be the main reasons for the formation of microstructural heterogeneity. On the one hand, the externally solidified crystals (ESCs) preferentially formed in the shot sleeve and aggregated in the casting center. On the other hand, the cooling rates were quite different in each region, leading to different solidification behaviors. Based on the combination of the microstructural observation and calculated cooling rates, a physical model has been proposed to describe the formation mechanism of the microstructural heterogeneity. The heterogeneous microstructure of the die-cast sample resulted in the inhomogeneity of mechanical properties along the thickness direction. The R 2 exhibited the highest micro-hardness than the other regions because of its highest amount of eutectics. Moreover, the casting surface with fine grains (R 1) is conducive to improving the EL, whereas the center (R 4 ) showed the lowest tensile properties due to the existence of ESCs and porosity band.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Material Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Improvement of the high-pressure die casting alloy Al-5.7Mg-2.6Si-0.7Mn with Zn addition10.1016/j.matchar.2019.109959 ↗
2. Microstructure formation in AlSi4MgMn and AlMg5Si2Mn high-pressure die castings10.1007/s11661-009-9841-1 ↗
3. Clustering characteristics of Fe-rich intermetallics in high vacuum die cast AlSiMgMn alloys with high resolution μ-CT inspection10.1016/j.matchar.2023.113607 ↗
4. Age-hardening of high pressure die casting AlMg alloys with Zn and combined Zn and Cu additions10.1016/j.matdes.2019.107927 ↗
5. Microstructure and mechanical properties of high strength die-casting Al-Mg-Si-Mn alloy10.1016/j.matdes.2012.10.020 ↗
6. Effect of runner design on the externally solidified crystals in vacuum die-cast Mg-3.0Nd-0.3Zn-0.6Zr alloy10.1016/j.jmatprotec.2018.12.032 ↗
7. Effects of solution treatment temperature and time on the porosities and mechanical properties of vacuum die-casted and T6 heat-treated Al-Si-Mg alloy10.1016/j.vacuum.2021.110536 ↗
8. 3D characterization of pores expansion behavior in high pressure die castings during heat treatment10.1016/j.matchar.2023.112710 ↗
9. Effect of vacuum degree and T6 treatment on the microstructure and mechanical properties of Al-Si-Cu alloy die castings10.1016/j.vacuum.2019.109063 ↗
10. The influence of T6 treatment on fracture behavior of hypereutectic Al-Si HPDC casting alloy10.1016/j.jallcom.2017.10.074 ↗
11. The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy10.1016/j.msea.2021.142544 ↗
12. Effect of high pressure die casting on the castability, defects and mechanical properties of aluminium alloys in extra-large thin-wall castings10.1016/j.jmatprotec.2022.117525 ↗
13. Cell-structure and flow stress investigation of largely strained non-heat-treatable Al-alloys using dislocation based model10.1016/j.msea.2018.10.007 ↗
14. Effect of Zr, Cr and Sc on the Al–Mg–Si–Mn high-pressure die casting alloys10.1016/j.msea.2019.05.038 ↗
15. Improved tensile properties of a new aluminum alloy for high pressure die casting10.1016/j.msea.2015.10.127 ↗
16. Multi-alloying effect of Sc, Zr, Cr on the Al-Mg-Si-Mn high-pressure die casting alloys10.1016/j.matchar.2020.110537 ↗
17. Development of high strength and toughness non-heated Al-Mg-Si alloys for high-pressure die-casting10.1007/s40195-020-01174-1 ↗
18. The effects of microstructure heterogeneities and casting defects on the mechanical properties of high-pressure die-cast AlSi9Cu3(Fe) alloys10.1007/s11661-014-2515-7 ↗
19. Macro-heterogeneities in microstructures, concentrations, defects and tensile properties of die cast Al-Mg-Si alloys10.1080/02670836.2017.1334309 ↗
20. Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties10.1016/j.jmatprotec.2021.117299 ↗
21. Microstructural evolution and solidification behavior of Al-Mg-Si alloy in high-pressure die casting10.1007/s11661-013-1663-5 ↗
22. Influence of pore characteristics and eutectic particles on the tensile properties of Al-Si-Mn-mg high pressure die casting alloy10.1016/j.msea.2020.139280 ↗
23. Thermodynamic description of the Al-Mg-Si system using a new formulation for the temperature dependence of the excess Gibbs energy10.1016/j.tca.2011.10.017 ↗
24. Microstructure and mechanical properties of pseudo binary eutectic Al-Mg2Si alloy processed by laser powder bed fusion10.1016/j.jmrt.2023.03.147 ↗
25. The gradient microstructure and deformation heterogeneity in HPDC AM60 alloy10.1016/j.msea.2020.139647 ↗
26. The ductility variation of high-pressure die-cast AE44 alloy: the role of inhomogeneous microstructure10.1007/s11661-021-06220-w ↗
27. Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: crack-inhibiting and multiple strengthening mechanisms10.1016/j.actamat.2020.03.060 ↗
28. Design strategy for eliminating cracking and improving mechanical properties of Al-Mg-Si alloys fabricated by laser melting deposition
29. Phase evolution and intermittent disorder in electrochemically Lithiated graphite determined using in operando neutron diffraction10.1021/acs.chemmater.9b05145 ↗
30. Quantitative analysis of interstitial mg in Mg2Si studied by single crystal X-ray diffraction10.1016/j.jallcom.2014.07.137 ↗
31. Microstructural evolution and hardness property of in situ Al–Mg2Si composites using one-step gravity casting method10.1080/00084433.2017.1345058 ↗
32. On the porosity induced by externally solidified crystals in high-pressure die-cast of AM60B alloy and its effect on crack initiation and propagation10.1016/j.msea.2015.02.078 ↗
33. The effect of solidification dynamics on the formation of the skin in die cast Mg-Al and Mg-RE alloys10.1002/adem.201200188 ↗
34. Microstructure and mechanical properties of inertia friction welded joints between high-strength low-alloy steel and medium carbon steel10.1016/j.jmatprotec.2020.116811 ↗
35. Microstructure and mechanical properties of repair welds of low-pressure sand-cast Mg-Y-RE-Zr alloy by tungsten inert gas welding10.1016/j.jma.2020.07.009 ↗
36. Influence of melt flow in the gating system on microstructure and mechanical properties of high pressure die casting AZ91D magnesium alloy10.1016/j.msea.2018.08.090 ↗
37. Cooling rate evaluation for bulk amorphous alloys from eutectic microstructures in casting processes10.2320/matertrans.43.1670 ↗
38. Experimental determination of cooling rates in selectively laser-melted eutectic Al-33Cu
39. Thermal behavior and microstructural evolution during laser deposition with laser-engineered net shaping: part I. Numerical calculations10.1007/s11661-008-9557-7 ↗
40. Lamellar and rod eutectic growth
41. Magnetic bilayer-skyrmions without skyrmion hall effect10.1038/ncomms10293 ↗
42. Dilatant shear bands in solidifying metals10.1038/nature05426 ↗
43. Transformation mechanism of (γ + γ’) and the effect of cooling rate on the final solidification of U720Li alloy10.1007/s40195-017-0566-7 ↗
44. Epitaxial laser metal forming analysis of microstructure formation10.1016/S0921-5093(99)00202-6 ↗
45. Multi-scale simulation of columnar-to-equiaxed transition during laser selective melting of rare earth magnesium alloy10.1016/j.jmst.2021.12.029 ↗
46. Hall-Petch relation and grain boundary slipping in Al-Mg-Sc alloys with fine equiaxed grain structure10.1016/j.matchar.2022.112472 ↗
47. Porosity quantification for ductility prediction in high pressure die casting AM60 alloy using 3D X-ray tomography10.1016/j.msea.2019.138781 ↗