journal article·2022-08

Cryogenically martensitic transformation and its effects on tempering behaviors of bearing steel

Zeju Weng, Kaixuan Gu, Jianpeng Zheng, Chen Cui, Mingli Zhang, Junjie Wang

Publisher page

Abstract

Herein, the cryogenically martensitic transformation and its effects on the tempering behaviors of bearing steel was investigated. An in-situ magnetic method was used for obtaining the thermodynamics of the martensitic transformation at sub-zero Celsius temperature from in respects of athermal and isothermal conditions. Microstructure evolution was also characterized systematically to investigate the mechanisms of the martensitic transformation. The results showed that the athermally martensitic transformation of samples experienced three different stages, where the martensite formed slowly at 300–230 K, rapidly at 230–120 K, and slowly again at 120–77 K during the continuous cooling process. With the increase of cooling rate, both the start and finish temperatures of the transformation rise, while the maximum transformed rate decreases. The content of retained austenite transformed isothermally is much smaller as compared to the athermal condition. The amount of isothermally formed martensite does not show linear relationship with the temperature, where an optimal isothermal temperature for GCr15 steel is 193 K in this work. XRD measurement result showed that the content of retained austenite decreased with the decrease of treating temperature in practical DCT, where the content was reduced up to 4.2% after DCT at the lowest temperature combined with tempering. DCT enhanced the precipitation of θ-carbides during tempering and altered the precipitation behavior by advancing the precipitated temperature of θ-carbides from 340 °C to 315 °C. The tempered hardness of samples was improved by DCT, which can be attributed to the enhanced carbides precipitation during tempering and lower content of retained austenite after DCT. The improvement was also affected by tempering and austenitizing temperatures. It was concluded that the performance improvement induced by DCT was most evident if DCT was conducted between higher temperature quenching and lower temperature tempering. DCT also affected the decomposition of retained austenite during tempering by decreasing the activation energy of decomposition by up to 38.13 KJ/mol, which indicated a lower thermal stability of retained austenite after DCT. Microstructure observation indicated that the substructure of the new formed martensite was dominated by ultra-fine twins, which derived from the accommodated strain induced by martensitic transformation during DCT. The transformation strain induced by DCT also causes more dislocations in the microstructure, which provides more nucleation sites for the precipitation of θ-carbides during tempering.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Effect of cryogenic treatment on tensile behavior of case carburized steel-815M1710.1016/j.matchar.2006.06.019 ↗
2. Effect of deep cryogenic treatment on structure-property relationship in an ultrahigh strength Mn-Si-Cr bainite/martensite multiphase rail steel10.1016/j.msea.2016.12.100 ↗
3. Juha Siiriainen, influence of shallow and deep cryogenic treatment on the residual state of stress of 4140 steel10.1016/j.jmatprotec.2010.10.018 ↗
4. Kurdjumov · 1948 · vol. 61
5. Isothermal martensitic transformation in sensitized SUS304 austenitic stainless steel at cryogenic temperature10.2320/matertrans.MBW200804 ↗
6. Isothermal martensite formation at sub-zero Celsius temperatures
7. Isothermal transformation of a CMnSi Steel below the Ms temperature10.1007/s11661-010-0557-z ↗
8. Stojko · 2006
9. The physical metallurgy of maraging steels
10. Isothermal martensitic transformation in Fe-Ni and Fe-Ni-C alloys at subzero temperatures10.1007/BF02647102 ↗
11. Villa · 2013
12. Kinetics of martensite formation in substitutional Fe-Al alloys: Dilatometric analysis10.1007/s11661-012-1497-6 ↗
13. Microstructure of low C steel isothermally transformaed in the Ms to Mf temperature range10.1007/s11661-012-1338-7 ↗
14. In situ investigation of the martensitic transformation in Fe–12 wt.%Ni–0.6 wt.%C steel at subzero temperatures10.1016/j.jallcom.2011.12.162 ↗
15. In-situ investigation of martensite formation in AISI 52100 bearing steel at sub-zero Celsius temperature
16. Thermally activated growth of lath martensite in Fe–Cr–Ni–Al stainless steel10.1179/1743284714Y.0000000583 ↗
17. Cryogenic treatment of an AISI D2 steel: the role of isothermal martensite formation and “martensite conditioning”10.1016/j.cryogenics.2020.103131 ↗
18. Activation energy of time-dependent martensite formation in steel10.1007/978-3-319-76968-4_2 ↗
19. Thermally activated martensite formation in ferrous alloys10.1016/j.scriptamat.2017.08.024 ↗
20. Martensite formation from reverted austenite at sub-zero Celsius temperature10.1007/s11661-018-4887-6 ↗
21. In Situ X-Ray diffraction analysis of microstructure evolution during deep cryogenic treatment and tempering of tool steels10.1002/srin.202100076 ↗
22. Tempering effects of athermal martensite during quenching and reheating of a SAE 52100 bearing steel
23. Effect of minimum temperature on the mechanical properties and reversed austenite content of 9%Ni steel subjected to cryogenic treatment10.1016/S1875-5372(18)30232-7 ↗
24. Effect of deep cryogenic treatment on the mechanical properties of tool steels10.1016/S0924-0136(01)00973-6 ↗
25. The reinforcement role of deep cryogenic treatment on the strength and toughness of alloy structural steel10.1016/j.msea.2019.138698 ↗
26. Carbide precipitation during tempering of a tool steel subjected to deep cryogenic treatment10.1007/s11661-014-2202-8 ↗
27. Low-temperature martensitic transformation in tool steels in relation to their deep cryogenic treatment10.1016/j.actamat.2012.11.045 ↗
28. Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel10.1016/j.msea.2020.139520 ↗
29. Martensitic transformation and stress partitioning in a high-carbon steel10.1016/j.scriptamat.2012.06.027 ↗
30. Evolution of compressive strains in retained austenite during sub-zero Celsius martensite formation and tempering10.1016/j.actamat.2013.11.007 ↗
31. Low-temperature martensitic transformation and deep cryogenic treatment of a tool steel10.1016/j.msea.2010.07.056 ↗
32. Effect of isothermal quenching on microstructure and hardness of GCr15 steel10.1016/j.jmrt.2021.09.096 ↗
33. A review on machinability aspects for AISI 52100 bearing steel
34. Steels for bearings10.1016/j.pmatsci.2011.06.002 ↗
35. Review analysis of the kinetics of phase transformation10.1007/BF01105093 ↗
36. On the magnetic investigation of the amount of retained austenite in quenched steels
37. Effect of deep cryogenic treatment on the fracture toughness and wear resistance of WC-Co cemented carbides10.1016/j.ijrmhm.2019.105059 ↗
38. Reaction kinetics in differential thermal analysis10.1021/ac60131a045 ↗
39. Analysis of the kinetics of phase transformations10.1007/BF01105093 ↗
40. Kinetics of isothermal martensitic transformation10.1016/0079-6425(86)90002-2 ↗
41. Rate of propagation of martensite
42. Real-time martensitic transformation kinetics in maraging steel under high magnetic fields10.1016/j.msea.2010.04.085 ↗
43. Unified model for plate and lath martensite with athermal kinetics10.1007/s11661-010-0239-x ↗
44. Kostorz · 2001
45. Stress-induced martensitic transformations in Cu-Zn-Al and Cu-ZnGa alloys10.1051/jphyscol:19824101 ↗
46. Defect-induced heterogeneous transformations and thermal growth in athermal martensite10.1103/PhysRevB.41.11319 ↗
47. The kinetics of martensite formation in steel10.1007/BF02814877 ↗
48. Direct observation of the gamma yields alpha prime isohtermal martensitic transformation of iron alloys in electron microscope10.2355/isijinternational1966.15.175 ↗
49. A new model explainable for both the athermal and isothermal natures of martensitic transformation in Fe-Ni-Mn alloys10.2320/matertrans1989.34.423 ↗
50. 2.47 GPa grade ultra-strong 15Co-12Ni secondary hardening steel with superior ductility and fracture toughness10.1016/j.jmst.2020.06.014 ↗
51. Tempering behavior of a direct laser deposited hot work tool steel: influence of quenching on secondary hardening and microstructure10.1016/j.msea.2021.141126 ↗
52. Nanoprecipitation in bearing steels10.1016/j.actamat.2011.08.007 ↗
53. Honeycombe · 1995