Effect of cooling rate on bending behavior of 6.5wt.% Si electrical steel thin sheets fabricated by strip casting and rolling
Source abstract
Abstract
Abstract Thin sheets of 6.5 wt.% Si electrical steel with the thickness of 0.35 mm were fabricated by strip casting and rolling. Influences of different cooling processes after annealing, including air cooling, water quenching, brine quenching and brine ice quenching, on the bending behavior at room temperature were systematically investigated. The results showed that with increase of the cooling rate, the room-temperature bending properties could be much improved, the fracture deflection values of the air cooled, water quenched, brine quenched and brine ice quenched specimens were measured to be 2.82 mm, 3.36 mm, 4.17 mm and 5.85 mm, respectively, moreover, obvious plastic deformation could be observed in the brine ice quenched specimen. The fracture modes of the air cooled and water quenched specimens were trans-granular cleavage fracture, while for the brine and brine ice quenched specimens, because the phosphorus segregation at grain boundary during high temperature could be preserved to room temperature by rapid quenching, the fracture modes were inter-granular fracture. The ordered phases in all specimens were observed and analyzed by TEM. The average sizes of B2 ordered domains in the air cooled, water quenched, brine quenched and brine ice quenched specimens were measured to be 107 nm, 2.7 nm, 1.6 nm, and 1.2 nm, respectively, and the DO 3 ordered domain with the average size of 2 nm could only be detected in the air cooled specimen. Therefore, the reduction of the order degree caused by fast cooling was believed to be mainly responsible for the improvement of bending properties, which might have led to significant decrease of the order-strengthening effect.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnetic Properties and Applications · Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Recent developments of new soft magnetic materials10.1016/0304-8853(94)90534-7 ↗
2. Ordering–disordering phenomena and micro-hardness characteristics of B2 phase in Fe–(5–6.5%) Si alloys10.1016/j.msea.2005.07.012 ↗
3. Effects of warm temper rolling on microstructure, texture and magnetic properties of strip-casting 6.5wt.% Si electrical steel10.1016/j.jmmm.2014.06.053 ↗
4. Microstructure and texture evolution of strip casting 3wt% Si non-oriented silicon steel with columnar structure10.1016/j.jmmm.2011.06.002 ↗
5. Formation of {001} 〈510〉 recrystallization texture and magnetic property in strip casting non-oriented electrical steel10.1016/j.matlet.2012.04.081 ↗
6. Development of λ-fiber recrystallization texture and magnetic property in Fe–6.5wt% Si thin sheet produced by strip casting and warm rolling method10.1016/j.matlet.2012.09.046 ↗
7. Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel10.1016/j.matchar.2013.11.014 ↗
8. Microstructure, texture and magnetic properties of strip casting Fe–6.2wt% Si steel sheet10.1016/j.jmatprotec.2012.04.015 ↗
9. Mathematical modeling of fluid flow, heat transfer, and solidification in two-roll melt drag thin strip casting of steel10.2355/isijinternational.40.144 ↗
10. Effect of coiling operation on strip quality of 4.5% Si steel in twin-roll casting process10.2355/isijinternational.39.463 ↗
11. Texture and magnetic properties of rolled Fe–6.5wt.% Si thin sheets10.1007/s11664-013-2842-2 ↗
12. Deformation twinning feature and its effects on significant enhancement of tensile ductility in columnar-grained Fe–6.5wt.% Si alloy at intermediate temperatures10.1016/j.intermet.2011.12.011 ↗
13. Deformation twinning in an Fe–6.5wt.% Si alloy with columnar grains during intermediate temperature compression10.1016/j.msea.2012.01.050 ↗
14. Directional recrystallization and microstructures of an Fe–6.5wt% Si alloy10.1557/jmr.2009.0303 ↗
15. Effects of order–disorder reactions on rapidly quenched Fe–6.5% Si alloy10.1016/j.jallcom.2012.09.074 ↗
16. Study of the brittle behaviour of annealed Fe–6.5wt% Si ribbons produced by planar flow casting10.1016/0921-5093(96)10188-X ↗
17. The influence of quench sensitivity on residual stresses in the aluminium alloys 7010 and 707510.1016/j.matchar.2012.01.005 ↗
18. Flow behavior and microstructures of large-grained Fe3Si during high temperature deformation10.1016/S0925-8388(02)00763-6 ↗
19. Influence of cooling rate on iron loss behavior in 6.5wt% grain-oriented silicon steel10.1016/j.jmmm.2013.10.004 ↗
20. Effect of DO3 ordered phase on total loss of 6.5wt% grain-oriented silicon steel10.1109/TMAG.2012.2206015 ↗
21. Effect of quench cooling rate on residual stress, microstructure and mechanical property of an Fe–6.5Si alloy10.1016/j.msea.2011.10.013 ↗
22. Prediction of residual stresses in quenched aluminum blocks and their reduction through cold working processes10.1016/j.jmatprotec.2006.02.007 ↗
23. Residual stress in 7449 aluminium alloy forgings10.1016/j.msea.2009.12.022 ↗
24. The effect of heat treatments and Si contents on B2 ordering reaction in high-silicon steels10.1016/S0921-5093(00)01960-2 ↗
25. Plastic deformation in Fe–Si alloys10.1007/BF02643136 ↗
26. The nature of dislocations and effect of order in rapidly solidified Fe-(5.5–7.5)wt.% Si alloys10.1016/0921-5093(93)90432-E ↗
27. Direct observation of antiphase boundaries in the Fe3Al superlattice10.1063/1.1702463 ↗
28. Theoretical analysis of plastic deformation in superlattices based on the body-centered cubic structure10.1063/1.1702703 ↗
29. Solute segregation at grain boundaries10.1007/BF00194704 ↗
30. Effect of phosphorus segregation on fracture properties of 2.25 Cr–1 Mo pressure vessel steel10.1361/105994903770343079 ↗