journal article·2023-01Open access

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Quinton C. Johnson, Peter Kenesei, Steve Petruzza, Jayden Plumb, Hemant Sharma, Jun-Sang Park, Elliott Marsden, Kristoffer Matheson, Michael W. Czabaj, Ashley D. Spear

Abstract

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography ( μ CT ) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μ CT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. A new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Cellular and Composite Structures · Automotive and Human Injury Biomechanics · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Multifunctionality of cellular metal systems10.1016/S0079-6425(98)00004-8 ↗
2. Effect of cell morphology on the compressive properties of open-cell aluminum foams10.1016/S0921-5093(00)00623-7 ↗
3. An investigation of the microstructure and strength of open-cell 6101 aluminum foams10.1007/s11661-002-0065-x ↗
4. The influence of cell-size distribution on the plastic deformation in metal foams10.1016/j.scriptamat.2003.09.046 ↗
5. Compressive response of open-cell foams. part i: Morphology and elastic properties10.1016/j.ijsolstr.2004.07.023 ↗
6. On the crushing of aluminum open-cell foams: Part i. experiments10.1016/j.ijsolstr.2008.09.008 ↗
7. The mechanics of three-dimensional cellular materials10.1098/rspa.1982.0088 ↗
8. The mechanical properties of cellular solids10.1007/BF02645546 ↗
9. Gibson · 1999
10. Effects of heat treatment on the compressive deformation behavior of open cell aluminum foams10.1016/S0921-5093(04)00933-5 ↗
11. Deformation and failure behaviour of open cell al foams under quasistatic and impact loading10.1016/j.msea.2013.08.030 ↗
12. Fracture and microstructure of open cell aluminum foam10.1007/s10853-005-4995-8 ↗
13. Influence of heat treatments on the microstructure and mechanical behaviour of open cell alsi7mg0. 3 foams on different lengthscales10.1016/j.actamat.2016.02.041 ↗
14. Two-scale study of the fracture of an aluminum foam by x-ray tomography and finite element modeling10.1016/j.matdes.2017.02.009 ↗
15. Microscale testing of the strut in open cell aluminum foams10.1007/s10853-005-6100-8 ↗
16. Grain size effects on the mechanical behavior of open-cell nickel foams10.1002/adem.200405153 ↗
17. Effect of grain size on the mechanical properties of mg foams10.1016/j.jmst.2020.03.067 ↗
18. Three-dimensional grain mapping of open-cell metallic foam by integrating synthetic data with experimental data from high-energy x-ray diffraction microscopy10.1016/j.matchar.2018.07.031 ↗
19. Review of third and next generation synchrotron light sources10.1088/0953-4075/38/9/022 ↗
20. Study of slip activity in a mg-y alloy by in situ high energy x-ray diffraction microscopy and elastic viscoplastic self-consistent modeling10.1016/j.actamat.2018.05.065 ↗
21. Quantification of cyclic twinning-detwinning behavior during low-cycle fatigue of pure magnesium using high energy x-ray diffraction10.1016/j.ijfatigue.2019.04.011 ↗
22. Modeling slip system strength evolution in ti-7al informed by in-situ grain stress measurements10.1016/j.actamat.2017.02.042 ↗
23. Investigation of fatigue crack initiation from a non-metallic inclusion via high energy x-ray diffraction microscopy10.1016/j.actamat.2017.07.027 ↗
24. Three-dimensional characterization of microstructurally small fatigue-crack evolution using quantitative fractography combined with post-mortem x-ray tomography and high-energy x-ray diffraction microscopy10.1016/j.actamat.2014.05.021 ↗
25. Forward modeling method for microstructure reconstruction using x-ray diffraction microscopy: Single-crystal verification10.1063/1.2400017 ↗
26. High-energy diffraction microscopy at the advanced photon source10.1007/s11837-011-0116-0 ↗
27. Far-field high-energy diffraction microscopy: a tool for intergranular orientation and strain analysis10.1177/0309324711405761 ↗
28. Far-field high-energy diffraction microscopy: a non-destructive tool for characterizing the microstructure and micromechanical state of polycrystalline materials10.1017/S1551929517000827 ↗
29. Overview of high-energy x-ray diffraction microscopy (hedm) for mesoscale material characterization in three-dimensions
30. High-energy x-ray diffraction microscopy in materials science10.1146/annurev-matsci-070616-124125 ↗
31. In-situ observation of bulk 3d grain evolution during plastic deformation in polycrystalline cu10.1016/j.ijplas.2014.10.013 ↗
32. Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline ti using high energy x-ray diffraction microscopy10.1016/j.actamat.2017.05.015 ↗
33. In-situ grain resolved stress characterization during damage initiation in cu-10% w alloy10.1007/s11837-019-03692-5 ↗
34. Afrl additive manufacturing modeling series: challenge 4, in situ mechanical test of an in625 sample with concurrent high-energy diffraction microscopy characterization10.1007/s40192-021-00218-3 ↗
35. New opportunities for quantitative tracking of polycrystal responses in three dimensions10.1016/j.cossms.2014.11.003 ↗
36. Understanding micromechanical material behavior using synchrotron x-rays and in situ loading10.1007/s11661-020-05888-w ↗
37. Manufacture, characterisation and application of cellular metals and metal foams10.1016/S0079-6425(00)00002-5 ↗
38. A multiscale comparison of stochastic open-cell aluminum foam produced via conventional and additive-manufacturing routes10.1016/j.msea.2017.08.102 ↗
39. Repeatability and sensitivity characterization of the far-field high-energy diffraction microscopy instrument at the advanced photon source10.1107/S1600577521008286 ↗
40. High energy x-ray micro-tomography for the characterization of thermally fatigued glidcop specimen
41. Characterization and application of a ge amorphous silicon flat panel detector in a synchrotron light source10.1016/j.nima.2007.08.103 ↗
42. Kaiser · 2007
43. On the calibration of high-energy x-ray diffraction setups. i. assessing tilt and spatial distortion of the area detector10.1107/S160057671400898X ↗
44. On the calibration of high-energy x-ray diffraction setups. ii. assessing the rotation axis and residual strains10.1107/S1600576714014290 ↗
45. Developments in synchrotron x-ray computed microtomography at the national synchrotron light source
46. U-net: Convolutional networks for biomedical image segmentation
47. Nih image to imagej: 25 years of image analysis10.1038/nmeth.2089 ↗
48. A fast methodology to determine the characteristics of thousands of grains using three-dimensional x-ray diffraction. i. overlapping diffraction peaks and parameters of the experimental setup10.1107/S0021889812025563 ↗
49. A fast methodology to determine the characteristics of thousands of grains using three-dimensional x-ray diffraction. ii. volume, centre-of-mass position, crystallographic orientation and strain state of grains10.1107/S0021889812025599 ↗
50. Dream. 3d: a digital representation environment for the analysis of microstructure in 3d10.1186/2193-9772-3-5 ↗
51. A tool to generate grain-resolved open-cell metal foam models10.1007/s40192-019-00136-5 ↗
52. Paraview: An end-user tool for large data visualization10.1016/B978-012387582-2/50038-1 ↗
53. High-throughput feature extraction for measuring attributes of deforming open-cell foams10.1109/TVCG.2019.2934620 ↗
54. Brannon · 2018
55. In-situ and ex-situ microtensile testing of individual struts of al foams and ni/al hybrid foams10.1016/j.matdes.2018.04.075 ↗
56. In-situ ebsd study of the active slip systems and lattice rotation behavior of surface grains in aluminum alloy during tensile deformation10.1016/j.msea.2013.05.046 ↗
57. Migration of grain boundaries under the influence of an external shear stress10.1016/S0921-5093(01)01193-5 ↗
58. Plane-strain compression of aluminum crystals10.1016/0001-6160(66)90196-9 ↗
59. Adaptive reconstruction method for three-dimensional orientation imaging10.1107/S0021889813005268 ↗
60. Selective laser melting (slm) of alsi12mg lattice structures10.1016/j.matdes.2016.02.127 ↗
61. Deformation and failure behaviour of ti-6al-4v lattice structures manufactured by selective laser melting
62. Effects of build orientation and heat treatment on the microstructure and mechanical properties of selective laser melted ti6al4v lattice structures
63. Inconel 625 lattice structures manufactured by selective laser melting (slm): mechanical properties, deformation and failure modes10.1016/j.matdes.2018.06.010 ↗
64. Microstructure and mechanical properties of aluminium alloy cellular lattice structures manufactured by direct metal laser sintering10.1016/j.msea.2015.01.063 ↗
65. On the microstructure of open-cell foams and its effect on elastic properties10.1016/j.ijsolstr.2007.10.008 ↗
66. Investigating the effect of grain structure on compressive response of open-cell metal foam using high-fidelity crystal-plasticity modeling10.1016/j.msea.2021.140847 ↗
67. Exploring new links between crystal plasticity models and high-energy x-ray diffraction microscopy10.1016/j.cossms.2019.07.002 ↗