journal article·2024-06

A laser powder bed fusion–based methodology for repairing damaged nickel-based turbine blades: Investigation of interfacial characteristics and hot isostatic pressing treatment

Di Wang, Zhenyu Liu, Guowei Deng, Xin Zhou, Sheng Li, Haoliang Wang, Yongqiang Yang, Changjun Han

Publisher page

Abstract

This study presents a methodology for repairing a damaged nickel-based turbine blade via laser powder bed fusion (LPBF) additive manufacturing. Specifically, the CM247LC nickel-based alloy was utilized to repair a damaged SRR99 nickel-based blade with LPBF, followed by hot isostatic pressing (HIP) post-treatment. The LPBF repair process achieved crack-free metallurgical bonding at the CM247LC/SRR99 interface with large epitaxially grown grains. Furthermore, HIP facilitated the formation of γ/γ’ phases with comparable dimensions at the interface as well as in the CM247LC and SRR99 regions through recrystallization. Additionally, the columnar grains in the LPBF-printed CM247LC region transformed into coarse equiaxed grains after HIP, accompanied by precipitation of nanoscale Hf-rich carbides. Meanwhile, microcracks in the LPBF-printed CM247LC region and shrinkage pores in the cast SRR99 region were effectively eliminated. The LPBF-printed CM247LC exhibited an 8.62% higher hardness compared to that of SRR99. The repaired samples showed an ultimate tensile strength of 791 MPa, with fracture occurring at the SRR99 side, indicating a reasonable metallurgical bonding strength at the CM247LC/SRR99 interface. The findings offer a novel alternative for the industrial application of repairing damaged nickel-based turbine blades.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. The effect of porosity size and oxidation on the HCF property of nickel-based single crystal superalloy at 980 degrees C10.1016/j.tafmec.2022.103423 ↗
2. Creep feed grinding induced gradient microstructures in the superficial layer of turbine blade root of single crystal nickel-based superalloy
3. Probability-based service safety life prediction approach of raw and treated turbine blades regarding combined cycle fatigue10.1016/j.ast.2021.106513 ↗
4. The springer model for lifetime prediction of wind turbine blade leading edge protection systems: a review and sensitivity study10.3390/ma15031170 ↗
5. Effect study and application to improve high cycle fatigue resistance of TC11 titanium alloy by laser shock peening with multiple impacts10.1016/j.surfcoat.2014.05.015 ↗
6. Assessment of the impact of shot-peening on the fatigue life of a compressor blade subjected to resonance vibrations10.3390/ma13245726 ↗
7. Microstructural characteristics and mechanical properties of repaired titanium alloy blade by arc additive manufacturing process10.1002/adem.202000187 ↗
8. Microstructure evolution and mechanical properties of a nickel-based superalloy repaired using wire and arc additive manufacturing10.1016/j.matchar.2022.112315 ↗
9. Zhou · 2023
10. Advanced additive remanufacturing technology
11. Additive manufacturing and its societal impact: a literature review10.1007/s00170-012-4558-5 ↗
12. Scaling up metal additive manufacturing process to fabricate molds for composite manufacturing(star;)
13. Towards additive manufacturing of compressor impellers: 3D modeling of multilayer laser solid freeform fabrication of nickel alloy 625 powder mixed with nano-CeO2 on AISI 4140
14. Review: the impact of metal additive manufacturing on the aerospace industry
15. Assessment of laser cladding as an option for repairing/enhancing rails10.1016/j.wear.2015.02.027 ↗
16. The role of laser additive manufacturing methods of metals in repair, refurbishment and remanufacturing–enabling circular economy10.1016/j.phpro.2016.08.077 ↗
17. Process development for tip repair of complex shaped turbine blades with IN71810.1016/j.promfg.2020.04.114 ↗
18. Optimization of STL model and layer shape for laser cladding forming10.1007/s00170-018-2714-2 ↗
19. Generating the tool path directly with point cloud for aero-engine blades repair10.1177/0954405420970915 ↗
20. Damage detection and reconstruction algorithm in repairing compressor blade by direct metal deposition10.1007/s00170-017-1413-8 ↗
21. Cracking, microstructure and tribological properties of laser formed and remelted K417G Ni-based superalloy
22. Laser engineered net shape (LENS) technology for the repair of Ni-base superalloy turbine components10.1007/s11661-014-2397-8 ↗
23. Laser remelting process simulation and optimization for additive manufacturing of nickel-based super alloys
24. Comparative energy, resource and recycling lifecycle analysis of the industrial repair process of gas turbine burners using conventional machining and additive manufacturing10.1111/jiec.12637 ↗
25. Energy · 2021
26. Additive manufacturing of ITER first wall panel parts by two approaches: selective laser melting and electron beam melting10.1016/j.fusengdes.2017.01.032 ↗
27. Role of heterogenous microstructure and deformation behavior in achieving superior strength-ductility synergy in zinc fabricated via laser powder bed fusion
28. Metal additive manufacturing: A review of mechanical properties
29. Cracking behavior and control of beta-solidifying Ti-40Al-9V-0.5Y alloy produced by selective laser melting10.1016/j.jmst.2019.08.026 ↗
30. Microstructure, cracking behavior and mechanical properties of Rene 104 superalloy fabricated by selective laser melting10.1016/j.jallcom.2020.158377 ↗
31. Microstructure and grain growth direction of SRR99 single-crystal superalloy by selective laser melting10.1016/j.jallcom.2019.151740 ↗
32. Microstructure and grain growth direction of SRR99 single-crystal superalloy by selective laser melting10.1016/j.jallcom.2019.151740 ↗
33. Process parameters and microstructure of Ni-based single crystal superalloy processed by selective laser melting
34. Crack inhibition to enhance strength-ductility of CM247LC alloy fabricated by laser powder bed fusion10.1016/j.msea.2023.145114 ↗
35. Focus shift analysis, to manufacture dense and crack-free SLM-processed CM247LC samples10.1016/j.jmatprotec.2020.116948 ↗
36. Heterogeneity of 316L/IN718 formed via selective laser melting based on laser remelting optimization process
37. Ultra-strong bond interface in additively manufactured iron-based multi-materials10.1016/j.msea.2020.140642 ↗
38. Research on a new SLM process of pre-melting and re-melting
39. Two-step heat treatment for laser powder bed fusion of a nickel-based superalloy with simultaneously enhanced tensile strength and ductility
40. Healing process of casting pores in a Ni-based superalloy by hot isostatic pressing10.1016/j.jmst.2015.07.004 ↗
41. Physics-based modeling of γ/γ’ microstructure evolution and creep constitutive relation for single crystal superalloy10.1016/j.ijplas.2020.102916 ↗
42. A quantitative role of rafting on low cycle fatigue behaviour of a directionally solidified Ni-based superalloy through a cross-correlated image processing method10.1016/j.ijfatigue.2019.105305 ↗
43. Review of γ’rafting behavior in nickel-based superalloys: crystal plasticity and phase-field simulation10.3390/cryst10121095 ↗
44. Additive manufacturing of CMSX-4 Ni-base superalloy by selective laser melting: influence of processing parameters and heat treatment
45. Rejuvenation of creep resistance of a Ni-base single-crystal superalloy by hot isostatic pressing10.1016/j.matdes.2017.08.059 ↗
46. Effect of alloying chemistry on MC carbide morphology in modified RR2072 and RR2086 SX superalloys10.1016/S1359-6462(02)00266-X ↗
47. MC carbide characterization in high refractory content powder-processed Ni-based superalloys10.1007/s11661-018-4587-2 ↗
48. Effect of Hf on carbides of FGH4096 superalloy produced by hot isostatic pressing10.1016/j.msea.2013.05.015 ↗
49. Effect of hafnium content on the microstructural evolution and stress rupture properties of K4750 nickel-based superalloy10.1016/j.jallcom.2022.165473 ↗
50. Impact of fluid flow on the dendrite growth and the formation of new grains in additive manufacturing
51. Cracking mechanism of Hastelloy X superalloy during directed energy deposition additive manufacturing
52. Electron backscatter diffraction analysis of inconel 718 parts fabricated by selective laser melting additive manufacturing10.1007/s11837-016-2198-1 ↗
53. Effects of hot isostatic pressing treatment on the microstructure and tensile properties of Ni-based superalloy CM247LC manufactured by selective laser melting10.1016/j.msea.2022.143083 ↗
54. Effect of heat treatment temperature on the microstructural evolution of CM247LC superalloy by laser powder bed fusion10.1016/j.matchar.2022.111742 ↗
55. Influence of Hf on the heat treatment response of additively manufactured Ni-base superalloy CM247LC10.1016/j.matchar.2020.110815 ↗
56. Interfacial characterization and mechanical properties of additively manufactured IN718/CoNiCrAlY laminate10.1016/j.msea.2022.143578 ↗
57. Correlation between microstructure heterogeneity and multi-scale mechanical behavior of hybrid LPBF-DED Inconel 62510.1016/j.jmatprotec.2022.117542 ↗
58. Design and development of SS316L-IN718 functionally graded materials via laser powder bed fusion10.1016/j.matlet.2023.134793 ↗
59. Characterization of multi-material 316L-Hastelloy X fabricated via laser powder-bed fusion10.1016/j.msea.2022.142749 ↗
60. Anomalous deformation behavior and twin formation of Ni-base superalloys at the intermediate temperatures10.1016/j.msea.2011.05.083 ↗
61. Orientation and temperature dependence of yielding and deformation behavior of a nickel-base single crystal superalloy10.1016/j.msea.2008.12.039 ↗
62. Microcrack nucleation and propagation investigation of inconel 740H alloy under in situ high temperature tensile test
63. Low-cycle fatigue behavior of K416B Ni-based superalloy at 650° C10.1007/s11771-021-4797-4 ↗
64. The hardness of additively manufactured alloys10.3390/ma11112070 ↗
65. Study on the strengthening and toughening mechanism of Mo-12Si-8.5B alloy with lanthanum oxide doped
66. Effect of microelement on microstructure and mechanical property of nickel-base Superalloy, journal of Netshape forming
67. Additive manufacturing of maraging steel-H13 bimetals using laser powder bed fusion technique
68. Microstructural investigation and mechanical behavior of a two-material component fabricated through selective laser melting of AlSi10Mg on an Al-Cu-Ni-Fe-Mg cast alloy substrate
69. Creep failure of low pressure turbine blade of an aircraft engine10.1016/j.engfailanal.2011.03.010 ↗
70. Nickel superalloy turbine blade parts printed by laser powder bed fusion: thermo-mechanical post-processing for enhanced surface integrity and precipitation strengthening10.1007/s11665-022-06710-x ↗