Effect of dislocation and residual stress on etching performance of 12 μm thick rolled copper foil during pre-stretching
Source abstract
Abstract
With the rapid development of new electronic information industry in 5G era, the development of various electronic components towards high speed and multi-functionality, and higher requirements have been put forward on the precision of circuit boards, the quality and rate of signal transmission. The 12 μm thick rolled copper foil is the thinnest rolled copper foil that can be stably produced, which is essential for the manufacture of high-end Flexible Printed Circuit (FPC) boards. The different microstructure and stress states of 12 μm thick rolled copper foil was obtained through different degrees of pre-stretching. And then the effect of dislocation and residual stress on the etching performance of copper foil was systematically investigated. The results show that the etching rate of copper foil increases and then decreases with the increasing of pre-stretching strain. And the etching rate of copper foil increases rapidly when the pre-stretching strain increases from 0.67% to 0.83%. For the dislocation, the rolled copper foil has higher dislocation density , and the dislocation density gradually increases with the increasing of pre-stretching strain. For the residual stress, the rolled copper foil has higher residual compressive stress. The residual compressive stress decreases and then turns into residual tensile stress with the increasing of pre-stretching strain. The residual compressive stress and dislocation reduce the etching rate of copper foil, and the residual tensile stress increases the etching rate of copper foil within a certain range. The four stages of etching rate variation of copper foil during pre-stretching were clarified, and the calculating model of etching rate was constructed when the dislocation density or residual stress acts as a single factor or dual factors.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Microstructure and mechanical properties · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Effect of post-annealing on the microstructure and mechanical properties of nanostructured copper10.1016/j.msea.2020.140666 ↗
2. Microstructural response of copper foil to a novel double-cross rolling process10.1016/j.jmrt.2020.11.003 ↗
3. Direct bonding of copper foil and liquid crystal polymer by laser etching and welding10.1016/j.optlaseng.2020.106509 ↗
4. Experimental characterization of rolled annealed copper film used in flexible printed circuit boards: identification of the elastic-plastic and low-cycle fatigue behaviors10.1016/j.microrel.2020.113976 ↗
5. Impact of plasma etching on fabrication technology of liquid crystal polymer printed circuit board10.1007/s10854-009-0024-z ↗
6. Influence of copper foil polycrystalline structure on graphene anisotropic etching10.1016/j.apsusc.2016.10.018 ↗
7. Development of flexible and functional sequins using subtractive technology and 3d printing for embroidered wearable textile applications10.3390/ma14102633 ↗
8. Effect of cupric ion concentration on the etching behavior of copper in Electrogenerated chemical polishing (EGCP)10.1016/j.precisioneng.2018.08.009 ↗
9. Recrystallization mechanisms and microstructure development in emerging metallic materials: a review10.1016/j.jsamd.2018.12.007 ↗
10. A novel severe plastic deformation method and its effect on microstructure, texture and mechanical properties of Mg-Gd-Y-Zn-Zr alloy10.1016/j.jallcom.2020.153698 ↗
11. Unique deformation behavior and microstructure evolution in high temperature processing of HfNbTaTiZr refractory high entropy alloy10.1016/j.actamat.2019.04.018 ↗
12. Twin evolution and work-hardening phenomenon of a bulk ultrafine grained copper with high thermal stability and strength-ductility synergy10.1016/j.msea.2020.140622 ↗
13. Improvement of mechanical property and corrosion resistance of Mg-Zn-Nd alloy by bi-direction drawing10.1016/j.jmst.2020.11.060 ↗
14. The effect of pre-deformation on corrosion resistance of the passive film formed on 2205 duplex stainless steel10.1016/j.jallcom.2016.06.003 ↗
15. Effects of pre-strain on the surface residual stress and corrosion behavior of an Al-Zn-Mg-Cu alloy plate10.1016/j.matchar.2020.110129 ↗
16. Effect of pre-strain on microstructure and stress corrosion cracking of over-aged 7050 aluminum alloy10.1016/j.jallcom.2008.01.137 ↗
17. Influence of pre-stretching and aging processes on comprehensive performance of aluminum alloy10.1080/10426914.2016.1221087 ↗
18. Effect of residual tensile stress and crystallographic structure on corrosion behavior of AZ31 Mg alloy rolled sheets
19. Atmospheric corrosion of field-exposed AZ31 magnesium in a tropical marine environment10.1016/j.corsci.2013.06.047 ↗
20. Corrosion of hot extrusion AZ91 magnesium alloy: I-relation between the microstructure and corrosion behavior10.1016/j.corsci.2011.02.015 ↗
21. Effects of deep cryogenic treatment on the microstructure and properties of rolled cu foil10.3390/ma14195498 ↗
22. Controllable fabrication of a carbide-containing FeCoCrNiMn high-entropy alloy: microstructure and mechanical properties10.1080/02670836.2017.1342367 ↗
23. Thermal stability of Cu-Nb microcomposite wires10.1016/j.actamat.2015.08.032 ↗
24. Effect of stacking fault energy on mechanical properties and annealing behavior of brasses10.1016/j.jallcom.2016.04.083 ↗
25. Deformation behaviors and cyclic strength assessment of AZ31B magnesium alloy based on steady ratcheting effect10.1016/j.msea.2018.03.023 ↗
26. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
27. Microstructure design to achieve optimal strength, thermal stability, and electrical conductivity of Al-7.5wt.%Y alloy10.1016/j.msea.2022.143700 ↗
28. Defect engineering in development of low thermal conductivity materials: a review10.1016/j.jeurceramsoc.2016.07.036 ↗
29. Combining severe plastic deformation and precipitation to enhance mechanical strength and electrical conductivity of Cu-0.65Cr-0.08Zr alloy10.1016/j.jmrt.2020.03.124 ↗
30. Variations of microstructure and properties of 690MPa grade low carbon bainitic steel after tempering10.1016/j.msea.2012.07.113 ↗
31. New insight into the role of microscale residual stresses on initial corrosion behavior of Ti35 alloy10.1016/j.corsci.2022.110491 ↗
32. Residual stress measurement of new and in-service X70 pipelines by X-ray diffraction method10.1016/j.ndteint.2011.03.003 ↗
33. Rolled electrodeposited copper foil with modified surface morphology as anode current collector for high corrosion resistance in lithium-ion battery electrolyte10.1016/j.surfcoat.2021.127369 ↗
34. FEM simulation of quenching process in A357 aluminum alloy cylindrical bars and reduction of quench residual stress through cold stretching process10.1016/j.commatsci.2012.11.024 ↗
35. Effect of pre-stretching on residual stresses and microstructures of inconel 718 superalloy10.3390/met11040614 ↗
36. Effect of tensile deformation on residual stress of GH4169 alloy10.3390/ma14071773 ↗
37. Influence of nano-SiC on microstructure and property of MAO coating formed on AZ91D magnesium alloy10.1016/S1003-6326(15)63800-6 ↗
38. Two-part epoxy-siloxane hybrid corrosion protection coatings for carbon steel10.1016/j.tsf.2009.03.114 ↗
39. Effect of electrolyte additives on performance of plasma electrolytic oxidation films formed on magnesium alloy AZ91D10.1016/j.electacta.2006.10.066 ↗
40. Role of β phase during microarc oxidation of Mg alloy AZ91D and corrosion resistance of the oxidation coating10.1016/j.jmst.2013.10.014 ↗
41. Corrosion behavior of Mg-2.4Zn alloy micro-alloyed with Ag and Ca10.1016/j.corsci.2013.09.012 ↗
42. Effects of voltage on microstructure and corrosion resistance of micro-arc oxidation ceramic coatings formed on KBM10 magnesium alloy10.1007/s11665-017-3088-6 ↗
43. Inhibition performance of 2-(Dibutylamino)-4,6-Dimercapto- 1,3,5-Triazine self-assembled film for copper corrosion in 3.5 wt% NaCl solutions10.20964/2019.08.46 ↗
44. Corrosion behavior of AZ31 magnesium alloy in the chloride solution containing ammonium nitrate10.1016/j.electacta.2018.05.059 ↗
45. Stainless steel surface structure and initial oxidation at nanometric and atomic scales10.1016/j.apsusc.2019.07.166 ↗
46. Orientation dependence of the electrochemical corrosion properties of electrodeposited Cu foils10.1016/j.corsci.2013.04.046 ↗
47. A green hydrothermal route to nanocrystalline CuCl10.1016/j.matlet.2006.12.041 ↗
48. Relationship between microstructure and etching performance of 12 μm thick rolled copper foil10.1016/j.jmrt.2022.10.009 ↗
49. Fractional brownian motion of dislocations during creep deformation of metals10.1016/j.msea.2020.140013 ↗
50. The role of texture and morphology in optimizing the corrosion resistance of zinc-based electrogalvanized coatings10.1016/S0010-938X(97)00148-0 ↗
51. Rapid assessment of anisotropic surface processes: experiments on the corrosion of Inconel 60010.1016/j.susc.2003.07.009 ↗
52. The role of overloading on the reduction of residual stress by cyclic loading in cold-drawn prestressing steelwires10.3390/app7010084 ↗
53. Prediction of residual stresses in quenched aluminum blocks and their reduction through cold working processes10.1016/j.jmatprotec.2006.02.007 ↗
54. Liu · 2004 · 46 · 405
55. Liu · 2006 · 48 · 3309
56. Fatigue performance rejuvenation of corroded 7075-T651 aluminum alloy through ultrasonic nanocrystal surface modification10.1016/j.ijfatigue.2021.106463 ↗
57. Massive parallel laser shock peening: simulation, analysis, and validation10.1016/j.ijfatigue.2007.01.033 ↗
58. Enhanced corrosion resistance of the surface modified Ti-13Nb-13Zr alloy by ultrasonic shot peening10.1016/j.corsci.2021.109597 ↗
59. E ff ectiveness of using low-temperature coolants in machining to enhance durability of AISI 316L stainless steel for reusable biomedical devices10.1016/j.jmapro.2019.02.003 ↗
60. The effect of residual stress on the electrochemical corrosion behavior of Fe-based amorphous coatings in chloride-containing solutions10.1016/j.surfcoat.2016.05.034 ↗
61. Influence of residual stresses on the fatigue crack growth from surface anomalies in a nickel-based superalloy10.1016/j.msea.2015.07.077 ↗
62. Evaluating the influence of residual stresses and surface damage on fatigue life of nickel superalloys10.1016/j.ijfatigue.2017.08.015 ↗
63. Experimental measurement of residual stress and distortion in additively manufactured stainless steel components with various dimensions10.1016/j.msea.2017.09.108 ↗
64. The influence of the support structure on residual stress and distortion in SLM Inconel 718 parts10.1007/s11661-018-4653-9 ↗
65. Investigating fatigue life prediction of rubber asphalt mixture based on damage evolution using residual strain analysis approach10.1016/j.conbuildmat.2020.119476 ↗