journal article·2016-04

An investigation on effect of heating mode and temperature on sintering of Fe-P alloys

A. Muthuchamy, Rajiv Kumar, A. Raja Annamalai, Dinesh K. Agrawal, Anish Upadhyaya

Publisher page

Abstract

Abstract The present study examines the effect of sintering temperature and heating mode on densification, microstructure and mechanical properties of Fe-P alloys. The green compacts were heated conventionally and in microwave under 95%N2–5%H2 (forming gas) at 1120 °C and 1250 °C for 60 min. Both the compositions (Fe-1.5P and Fe-3P in wt%) were found to couple well in microwave field with rapid heating (~ 40 °C min− 1) and resulted in reduction of overall processing time by about 90% in comparison of conventional heating. Microwave sintering resulted in higher densification in case of Fe-P alloys. Moreover, an important feature of microwave and conventionally sintered samples was that their microstructures exhibited distinctly rounded pores. This resulted into improved corrosion and mechanical properties in general.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microwave-Assisted Synthesis and Applications · Advanced materials and composites · Materials Engineering and Processing

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. Upadhyaya · 1999 · 1
2. German · 1994
3. German · 1985
4. Microwave sintering, brazing and melting of metallic materials
5. Full sintering of powdered-metal bodies in a microwave field10.1038/21390 ↗
6. Effect of sintering parameters on magnetic properties of Fe-0.45P sintered materials10.1179/pom.1992.35.4.292 ↗
7. Sintering and microstructure of phosphorous steels10.1179/pom.1992.35.4.285 ↗
8. On phosphorous as additive in iron based soft PM magnets10.1179/003258904225020819 ↗
9. Microwave processing: fundamentals and applications10.1016/S1359-835X(99)00020-2 ↗
10. High temperature microwave processing of materials10.1088/0022-3727/34/13/201 ↗
11. Microwave sintering of ferrous PM materials
12. Improved mechanical properties and microstructural development of microwave sintered copper and nickel steel PM parts10.1179/003258905X37657 ↗
13. Microwave sintering of iron, cobalt, nickel, copper and stainless steel powders10.1016/j.scriptamat.2005.11.006 ↗
14. Microwave sintering: a new approach to fine-grain tungsten-I
15. Microwave sintering of W-Ni-Fe alloy10.1016/j.scriptamat.2006.09.010 ↗
16. Effect of heating mode on the densification and microstructural homogenization response of premixed bronze10.1016/j.scriptamat.2006.11.031 ↗
17. Microwave synthesis and characterization of metastable (Al/Ti) and hybrid (Al/Ti+SiC) composites10.1016/j.msea.2006.10.156 ↗
18. Development of Mg/Cu nanocomposites using microwave assisted rapid sintering10.1016/j.compscitech.2006.07.015 ↗
19. Mondal · Mater Sci Eng A · 2010 · 527 · 687010.1016/j.msea.2010.07.074 ↗
20. Padmavathi · Mater Chem Phys · 2011 · 130 · 44910.1016/j.matchemphys.2011.07.008 ↗
21. Effect of heating mode on sinterability of Fe-Ni steels10.1080/08327823.2011.11689811 ↗
22. Effect of Fe3P addition on magnetic properties and structure of sintered iron10.1179/pom.1980.23.4.210 ↗
23. Pert · J Am Ceram Soc · 2001 · 84 · 198110.1111/j.1151-2916.2001.tb00946.x ↗
24. 1998
25. 1997
26. 2004 · Vol 9 · 1017
27. MPIF Standard 10: “Tension test specimens for pressed and sintered metal powders”,.
28. Structure and corrosion behavior of iron-based metallic glass coatings prepared by LPPS10.1016/j.apsusc.2012.02.015 ↗
29. Bardal · 2004 · 9
30. Effect of heating mode on the densification and microstructural homogenization response of premixed bronze10.1016/j.scriptamat.2006.11.031 ↗
31. Mechanical behavior of novel phosphoric irons for concrete reinforcement applications10.1016/j.scriptamat.2006.09.031 ↗
32. On the corrosion resistance of the Delhi iron pillar10.1016/S0010-938X(00)00046-9 ↗
33. Characterization of Delhi iron pillar rust by X-ray diffraction, Fourier Transform Infrared Spectroscopy and Mössbauer Spectroscopy10.1016/S0010-938X(00)00045-7 ↗
34. Enhanced sintering for ferrous components
35. 1991
36. Sintering of 434L ferritic stainless steel containing Al2O3 particles
37. Corrosion and protection of sintered metal parts10.1179/pom.1977.20.4.227 ↗