journal article·2026-01

Tailoring microstructure and performance of thick-walled SS316L through overlap control in wire arc directed energy deposition

Ramesh Mamedipaka, Amit Kumar Yadav, Sunil Sinhmar, Halid Can Yıldırım, Shivraman Thapliyal

Publisher page

Abstract

This study investigates the influence of overlapping deposition strategies (ODS) on the microstructural evolution, mechanical properties, and corrosion behaviour of thick-walled 316 L stainless steel fabricated using Wire Arc Directed Energy Deposition (Wa-DED). Multi-bead multi-layer (MBML) blocks were fabricated with two overlapping conditions representing ODS-1 (0.63 W) and ODS-2 (0.73 W) and characterized for mechanical and corrosion properties along both the overlap (OD) and transverse (TD) directions. Microstructural investigation using optical microscopy, SEM, EBSD, and synchrotron XRD revealed that ODS-2 promotes a more uniform grain size distribution (56.15–57.28 μm) and lower δ-ferrite content owing to controlled thermal gradients, while ODS-1 exhibits higher ferrite fractions and larger primary dendrite arm spacing (PDAS) from increased heat accumulation. EBSD analysis indicated a strong 〈001〉||WD texture in both conditions, with ODS-2 (OD) displaying enhanced texture intensity (24.985) and favourable {111} orientations. ODS-2 (OD) exhibited higher tensile strength (YS: 415 ± 16 MPa, UTS: 570 ± 17 MPa) than ODS-1, attributed to finer grains and higher dislocation density (∼2.12 × 1015 m−2) comparatively. Corrosion behaviour in 3.5 wt% NaCl revealed superior resistance in ODS-2 (icorr: 0.15 μA/cm2 in TD), attributed to reduced ferrite, uniform Cr/Mo distribution, and a stable passive film. These findings highlight the critical role of overlap distance in tailoring microstructural features for enhanced mechanical and corrosion performance in Wa-DED SS316L components.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Hydrogen embrittlement and corrosion behaviors in metals · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (66)

Show source-provided references
1. Wire-feed additive manufacturing of metal components: technologies, developments and future interests10.1007/s00170-015-7077-3 ↗
2. A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement10.1016/j.jmapro.2018.08.001 ↗
3. A review on microstructural and tribological performance of additively manufactured parts10.1007/s10853-022-07736-1 ↗
4. A layers-overlapping strategy for robotic wire and arc additive manufacturing of multi-layer multi-bead components with homogeneous layers10.1007/s00170-018-1786-3 ↗
5. Data-driven model for predicting tensile properties of wire arc additive manufactured 316L steels and its validation
6. Investigating the microstructure and mechanical behavior of optimized eutectic Al – Si alloy developed by direct energy deposition10.1016/j.jmapro.2024.01.002 ↗
7. Strategy for developing aluminum alloy-based solid structure with homogeneous properties in the overlapping direction using wire arc additive manufacturing10.1080/01694243.2024.2352270 ↗
8. Generalised overlapping model for multi-material wire arc additive manufacturing (WAAM)10.1080/17452759.2023.2210541 ↗
9. A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)10.1016/j.rcim.2014.08.008 ↗
10. Investigation of the overlapping parameters of MPAW-based rapid prototyping10.1108/13552540610670744 ↗
11. Weld bead modeling and process optimization in hybrid layered manufacturing10.1016/j.cad.2011.01.006 ↗
12. Enhanced beads overlapping model for wire and arc additive manufacturing of multi-layer multi-bead metallic parts10.1016/j.jmatprotec.2017.10.017 ↗
13. Multi-bead overlapping model with varying cross-section profile for robotic GMAW-based additive manufacturing10.1007/s10845-019-01501-z ↗
14. Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel10.1016/j.msea.2019.02.078 ↗
15. Microstructural characterisation of thick-walled wire arc additively manufactured stainless steel10.1016/j.jmatprotec.2021.117373 ↗
16. Anisotropy of microstructure and corrosion resistance of 316L stainless steel fabricated by wire and arc additive manufacturing10.1016/j.corsci.2022.110549 ↗
17. Adjusting microstructure and improving mechanical property of additive manufacturing 316L based on process optimization10.1016/j.msea.2023.144824 ↗
18. On the anisotropy of thick-walled wire arc additively manufactured stainless steel parts10.1016/j.msea.2022.144538 ↗
19. In-situ observation of deformation behavior of the periodic structure in 316L stainless steel fabricated by wire and arc additive manufacturing10.1016/j.matchar.2023.113162 ↗
20. Effects of the thermal history on the microstructural and the mechanical properties of stainless steel 316L parts produced by wire-based laser metal deposition10.1016/j.msea.2023.145862 ↗
21. Enhancing microstructural integrity and mechanical performance of thick wire-arc directed energy deposited eutectic aluminum-silicon solid structure through continuous multi-pass friction stir processing10.1016/j.msea.2024.147155 ↗
22. Influence of the printing strategy on the microstructure and mechanical properties of thick-walled wire arc additive manufactured stainless steels10.1016/j.jmatprotec.2023.118275 ↗
23. Strengthening mechanisms in selective laser melted 316L stainless steel10.1016/j.msea.2021.142434 ↗
24. Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel | Cementação sob plasma à baixa temperatura do aço inoxidável austenítico AISI 316L e do aço inoxidável duplex AISI F5110.1590/S0370-44672013000200011 ↗
25. Dislocation microstructure and its influence on corrosion behavior in laser additively manufactured 316L stainless steel
26. Microstructural heterogeneity and exceptional mechanical properties in a wire-arc additively manufactured stainless steel10.1016/j.msea.2023.145473 ↗
27. Investigation of surface nanostructuring, mechanical performance and deformation mechanisms of AISI 316L stainless steel treated by surface mechanical impact treatment10.1007/s12540-022-01286-6 ↗
28. Effect of geometrically necessary dislocations induced strain on the corrosion behavior of Ni coatings with different surfactants10.1016/j.mtla.2022.101431 ↗
29. On the pitting corrosion of 2205 duplex stainless steel produced by laser powder bed fusion additive manufacturing in the as-built and post-processed conditions10.1016/j.matdes.2021.110260 ↗
30. Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes10.1016/j.jmst.2019.03.003 ↗
31. Investigation of corrosion and electrical resistance in laser welded Al-cu joints for EV batteries10.1016/j.est.2024.114436 ↗
32. Influence of scanning strategy and building direction on microstructure and corrosion behaviour of selective laser melted 316L stainless steel10.1016/j.matdes.2021.109999 ↗
33. Inhibiting corrosion of aluminum alloy 7075 beneath a thin liquid film containing aspergillus terreus10.1016/j.corsci.2025.112912 ↗
34. Effects of crystallographic orientation on the corrosion behavior of stainless steel 316L manufactured by laser powder bed fusion10.1016/j.corsci.2021.110009 ↗
35. Microstructure and corrosion behavior of a novel additively manufactured maraging stainless steel10.1016/j.electacta.2020.135925 ↗
36. Effect of build orientation and annealing on corrosion resistance of additively manufactured duplex stainless steel in 3.5% NaCl10.1149/1945-7111/abc5dd ↗
37. The analysis of electrode impedances complicated by the presence of a constant phase element10.1016/S0022-0728(84)80324-1 ↗
38. Concernng the conversion of the constant phase element parameter Y0 into a capacitance10.5006/1.3280607 ↗
39. Determination of effective capacitance and film thickness from constant-phase-element parameters10.1016/j.electacta.2009.10.065 ↗
40. Closed loop control of melt pool width in robotized laser powder–directed energy deposition process10.1007/s00170-019-04195-y ↗
41. Machine learning-assisted wire arc additive manufacturing and heat input effect on mechanical and corrosion behaviour of 316 L stainless steels10.1016/j.istruc.2024.107126 ↗
42. Investigation on thermal stress evolution induced by wire and arc additive manufacturing for circular thin-walled parts10.1016/j.jmapro.2019.03.006 ↗
43. A digital twin for rapid qualification of 3D printed metallic components10.1016/j.apmt.2018.11.003 ↗
44. Laser-arc hybrid additive manufacturing of stainless steel with beam oscillation
45. Modelling and experimental observation of the deposition geometry and microstructure evolution of aluminum alloy fabricated by wire-arc additive manufacturing10.1016/j.jmapro.2021.01.037 ↗
46. Effect of heat treatment on microstructure, mechanical and corrosion properties of austenitic stainless steel 316L using arc additive manufacturing10.1016/j.msea.2017.10.002 ↗
47. The role of side-branching in microstructure development in laser powder-bed fusion10.1038/s41467-020-14453-3 ↗
48. Morphological stability of solid-liquid interfaces under additive manufacturing conditions10.1016/j.actamat.2023.118858 ↗
49. Columnar-to-equiaxed transition in laser fusion additive manufacturing10.1016/j.scriptamat.2025.116565 ↗
50. The rapid solidification processing of materials: science, principles, technology, advances, and applications10.1007/s10853-009-3995-5 ↗
51. Towards understanding grain nucleation under additive manufacturing solidification conditions10.1016/j.actamat.2020.05.012 ↗
52. A novel mechanism to generate metallic single crystals10.1038/s41598-021-04235-2 ↗
53. Electron beam additive manufacturing of SS316L with a stochastic scan strategy: microstructure, texture evolution, and mechanical properties10.3390/met14111278 ↗
54. Orientation dependent tensile properties of a selective-laser-melt 316L stainless steel10.1016/j.msea.2021.141808 ↗
55. Crystallographic-orientation-dependent tensile behaviours of stainless steel 316L fabricated by laser powder bed fusion10.1016/j.msea.2019.138395 ↗
56. Synchrotron diffraction characterization of dislocation density in additively manufactured IN 718 superalloy10.1016/j.matchar.2021.111379 ↗
57. The effect of dislocation contrast on x-ray line broadening: a new approach to line profile analysis10.1063/1.117951 ↗
58. High strength and ductility of additively manufactured 316L stainless steel explained10.1007/s11661-018-4607-2 ↗
59. An improved X-ray diffraction analysis method to characterize dislocation density in lath martensitic structures10.1016/j.msea.2015.05.003 ↗
60. Mechanisms of inclusion-induced pitting of stainless steels: a review10.1016/j.jmst.2023.06.008 ↗
61. Correlation between growth texture, crystallite size, lattice strain and corrosion behavior of copper-carbon nanotube composite coatings10.1016/j.surfcoat.2020.126596 ↗
62. Electrochemical insight into the passivity and corrosion of 316 L stainless steel fabricated through wire arc additive manufacturing10.1016/j.colsurfa.2024.134085 ↗
63. Effects of linear heat input on microstructure and corrosion behavior of an austenitic stainless steel processed by wire arc additive manufacturing10.1016/j.vacuum.2019.109131 ↗
64. Corrosion mechanism of additively manufactured 316 L stainless steel in 3.5 wt.% NaCl solution
65. On the enhanced corrosion resistance of a selective laser melted austenitic stainless steel10.1016/j.scriptamat.2017.07.037 ↗
66. A novel understanding of dislocation density effect on the corrosion resistance of 316L stainless steel with passive film nucleation growth kinetic calculation10.1016/j.corsci.2025.112810 ↗