journal article·2024-11

On the influence of austenite content in orientation selectivity and shear texture evolution during hot rolling of Fe-3 wt% Si grain-oriented electrical steel

Rahul Kumar Rai, Vikash Kumar Sahu, S.K. Pradhan, V. Rajinikanth, B.K. Sahoo, Poulami Maji, Snehashish Tripathy, Sandip Ghosh Chowdhury

Publisher page

Abstract

A systematic investigation of the development of shear textures during hot rolling of Fe – 3 wt% Si steel has been carried out in the present work with a special focus on the influence of austenite in preferential orientation selectivity. This orientation selectivity was anticipated owing to the fact that texture evolution during thermomechanical processing is entirely an effect of crystallographic rotations and such rotations may experience constraining effects because of surrounding austenite. The influence of austenite on shear texture evolution was studied over a range of finish rolling temperatures (FRTs). The evolution of microstructure and microtexture within the surface-subsurface zone was studied adopting EBSD. Sharp Goss orientation was observed at lower FRT, while texture intensities of Brass and Copper were observed to be high at higher FRT. Additionally, it was inferred that in the surface-subsurface zone, next to the austenite, the ease of rotation about ND contributed to the higher observed frequency of the Brass orientation despite of its overall lesser fraction as compared to Copper orientation. The less observed frequency of Copper orientation near the austenite has been attributed to the resistance offered by the austenite to its adjacent ferrite grains while rotating about TD. This constraining effect of austenite has been shown to be consistent over the entire range of studied FRTs. Moreover, it has been shown that at higher rolling temperatures, the lower constraining effect by austenite paves the way for Goss orientation formation, which acts as the precursor to the formation of Brass at the FRT.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnetic Properties and Applications · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (95)

Show source-provided references
1. Energy efficient electrical steels: magnetic performance prediction and optimization10.1016/j.scriptamat.2012.02.027 ↗
2. On magnetization of single crystals of iron
3. Development of low-loss grain-oriented silicon steel10.1007/BF02649332 ↗
4. Effect of aluminum and nitrogen on the magnetic properties of non-oriented semi-processed electrical steel sheet10.1016/S0304-8853(00)00005-6 ↗
5. On the correlation of crystallographic macro-texture and magnetic magnetization anisotropy in non-oriented electrical steel10.1016/j.jmmm.2019.165485 ↗
6. Effect of texture and grain size on magnetic flux density and core loss in non-oriented electrical steel containing 3.15% Si10.1016/j.jmmm.2013.11.030 ↗
7. Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting10.1016/j.matchar.2019.02.001 ↗
8. De Cooman · 2007
9. The orientation of crystals in silicon iron
10. Recent development of technology of grain oriented silicon steel10.4028/www.scientific.net/MSF.204-206.143 ↗
11. 2000
12. Recent technology developments in the production of grain-oriented electrical steel10.1002/srin.200506030 ↗
13. Influence of intermediate annealing on final Goss texture formation in low temperature reheated Fe-3% Si steel10.1016/j.msea.2010.10.079 ↗
14. A note on grain size dependent pinning10.1016/j.scriptamat.2005.02.021 ↗
15. Abnormal growth of Goss grains in grain-oriented electrical steels10.1016/S1005-0302(10)60120-X ↗
16. Primary recrystallization characteristics and magnetic properties improvement of high permeability grain-oriented silicon steel by trace Cr addition10.1016/j.jmmm.2020.166849 ↗
17. Structure analysis of aluminium silicon manganese nitride precipitates formed in grain-oriented electrical steels10.1016/j.matchar.2013.09.014 ↗
18. The Goss texture formation in silicon steels–growth selection or oriented nucleation?10.4028/www.scientific.net/SSP.105.29 ↗
19. Effects of topology on abnormal grain growth in silicon steel
20. Influence of primary-recrystallization texture on selective growth of goss grains10.2320/matertrans.M2012303 ↗
21. The role of grain boundary character distribution in Goss texture development in electrical steels10.1016/0304-8853(96)00141-2 ↗
22. The role of grain boundary character distribution in secondary recrystallization of electrical steels10.1016/S1359-6454(96)00251-0 ↗
23. Coincidence grain boundary and texture evolution in Fe-3% Si10.1016/0001-6160(89)90118-1 ↗
24. Texture evolution by grain growth in the presence of MnS and AlN precipitates in Fe-3% Si alloy10.1016/0956-7151(90)90107-R ↗
25. The development of grain-oriented silicon steel with high permeability10.1016/0304-8853(75)90114-6 ↗
26. A new high induction grain oriented 3% silicon-iron10.1109/TMAG.1977.1059578 ↗
27. Origin and development of through-the-thickness variations of texture in the processing of grain-oriented silicon steel10.1007/BF02650112 ↗
28. Humphreys · 2012
29. Effect of hot rolling reduction on microstructure, texture and ductility of strip-cast grain-oriented silicon steel with different solidification structures10.1016/j.msea.2014.03.052 ↗
30. Evolution of recrystallization texture in nonoriented electrical steels10.1016/S1359-6454(03)00115-0 ↗
31. Retention of the Goss orientation between microbands during cold rolling of an Fe3% Si single crystal10.1016/j.actamat.2006.11.048 ↗
32. Role of shear bands in annealing texture formation in 3% Si–Fe (111) [112] single crystals10.2355/isijinternational.29.862 ↗
33. Survival of Goss grains during cold rolling of a silicon steel single crystal10.4028/www.scientific.net/MSF.495-497.1061 ↗
34. A study of local microstructure and texture heterogeneities in a CGO Fe3% Si alloy from hot rolling to primary recrystallization10.4028/www.scientific.net/MSF.495-497.483 ↗
35. Characterization of global and local textures in hot rolled CGO Fe3% Si10.4028/www.scientific.net/MSF.509.25 ↗
36. Formation of the Goss orientation near the surface of 3 pct silicon steel during hot rolling10.1007/BF02650113 ↗
37. Cold-rolled and primary recrystallization textures in cold-rolled single crystals of silicon iron10.1016/0001-6160(54)90156-X ↗
38. On the development of the goss texture in iron-3% silicon10.1016/0001-6160(84)90161-5 ↗
39. New information on texture development in regular and high-permeability grain-oriented silicon steels10.1007/BF02650111 ↗
40. On the through-process texture evolution assessment in grain oriented Fe-3 wt% Si steel produced by a novel directional inoculation technique10.1038/s41598-021-84360-0 ↗
41. On the development of Fe – 3% Si steel hot band: hot rolling, microtexture evolution and recrystallization behaviour
42. A study of surface textures in cold-rolled single crystals of silicon iron with reference to new lubricating materials10.2355/isijinternational1966.18.99 ↗
43. Formation of cold-rolled texture and recrystallized texture in single crystals of 3% silicon Iron (part I)-cold-rolled texture10.2355/isijinternational1966.6.290 ↗
44. The effect of orientation on the recrystallization kinetics of cold-rolled single crystals
45. Effect of carbon on texture formation in electrical steel Fe–3% Si under hot rolling10.1007/s11041-015-9815-4 ↗
46. Influence of initial annealing on structure evolution and magnetic properties of 3.4% Si non-oriented steel during final annealing10.1016/j.jmmm.2015.05.058 ↗
47. Effect of initial grain size on texture evolution and magnetic properties in nonoriented electrical steels10.1016/j.jmmm.2008.12.015 ↗
48. Effect of hot-band grain size and intermediate annealing on magnetic properties and texture of non-oriented silicon steels10.1016/j.jmmm.2006.02.189 ↗
49. Contribution of shear banding to origin of Goss texture in silicon iron10.1179/030634584790420258 ↗
50. The influence of shear bands on final structure and magnetic properties of 3% Si non-oriented silicon steel10.1016/j.jmmm.2008.04.050 ↗
51. The development of rolling textures in low-carbon steels10.1155/TSM.1.129 ↗
52. Cold-rolled textures of silicon-iron crystals10.1007/BF03377518 ↗
53. Texture evolution of columnar grains in electrical steel during hot rolling10.1016/S1006-706X(13)60184-3 ↗
54. Effect of {110}< 229> and {110}〈112〉 grains on texture evolution during cold rolling and annealing of electrical steel10.2355/isijinternational.ISIJINT-2016-145 ↗
55. Behaviors of brass texture and its influence on Goss texture in grain oriented electrical steels10.3724/SP.J.1037.2011.00421 ↗
56. Influence of primary recrystallization texture through thickness to secondary texture on grain oriented silicon steel10.2355/isijinternational.43.400 ↗
57. Texture evolution of a 2.8 wt% Si non-oriented electrical steel during hot band annealing10.1088/1757-899X/375/1/012014 ↗
58. Relationship between the initial {100} textures and the shear textures developed in sheet surface during hot rolling of non-oriented silicon steel10.1016/j.matchar.2021.111534 ↗
59. Study of local microstructure and texture heterogeneities in hot rolled CGO Fe-3% Si sheets10.4028/www.scientific.net/MSF.467-470.123 ↗
60. Recent developments in grain-oriented silicon-steel10.1016/0304-8853(96)00126-6 ↗
61. 1981
62. 1968
63. Hot deformation and recrystallization of 3% silicon steel part 1: microstructure, flow stress and recrystallization characteristics10.2355/isijinternational.45.1666 ↗
64. The influence of normalisation temperatures on different texture components and magnetic properties of nonoriented electrical steels10.1002/srin.202000361 ↗
65. Analysis of dynamic static recrystallization microstructure and orientations in a hot-compressed electrical steel
66. Secondary recrystallization textures and their origin in cold-rolled single crystals of silicon iron10.1016/0001-6160(53)90055-8 ↗
67. Secondary recrystallization in silicon iron
68. Effects of hot rolling on microstructures and magnetic properties10.4283/JMAG.2006.11.3.111 ↗
69. Texture evolution in grain-oriented electrical steel during hot band annealing and cold rolling10.1111/j.1365-2818.2008.02001.x ↗
70. Effect of carbon content on the grain refinement of locally produced plain carbon steel by thermal cycling
71. Effect of carbon content on microstructure and mechanical properties of dual phase steels10.1016/j.mspro.2015.04.167 ↗
72. Flow curve correction and processing map of 2050 Al-Li alloy10.1016/S1003-6326(18)64674-6 ↗
73. Analysis of deformation textures of asymmetrically rolled steel sheets10.1016/S0020-7403(01)00025-X ↗
74. Texture evolution in twin-roll strip cast non-oriented electrical steel with strong cube and Goss texture10.1016/j.actamat.2020.08.048 ↗
75. Adaptive domain misorientation approach for the EBSD measurement of deformation induced dislocation sub-structures10.1016/j.ultramic.2021.113203 ↗
76. Texture, misorientation and mechanical anisotropy in a deformed dual phase stainless steel weld joint10.1016/j.msea.2013.03.018 ↗
77. A comparison of EBSD based strain indicators for the study of Fe-3Si steel subjected to cyclic loading10.1016/j.matchar.2016.03.020 ↗
78. Effect of composition and deformation on coarse-grained austenite transformation in Nb-Mo microalloyed steels10.1007/s11661-011-0624-0 ↗
79. Orientation evolutions during hot rolling of electrical steel containing initial columnar grains
80. Finite element modelling of effects of roll gap geometry in hot rolling10.1179/174328405X47546 ↗
81. On the grain boundary character evolution in non equiatomic high entropy alloy during hot rolling induced dynamic recrystallization10.1016/j.jallcom.2022.166126 ↗
82. The formation of the {112}〈111〉 shear texture in hot-rolled sheets of electrical steels10.1002/srin.202200939 ↗
83. Grain refinement by high temperature plane-strain compression of Fe-2% Si steel10.4028/www.scientific.net/MSF.503-504.977 ↗
84. Effects of rolling reduction and annealing temperature on the recrystallization structure of solidified columnar crystals in a 19% Cr ferritic stainless steel10.2355/isijinternational.34.1008 ↗
85. Some applications of the Taylor theory of polycrystal plasticity10.1002/crat.19700050112 ↗
86. The deformation behaviour of hard and soft grains in RR1000 nickel-based superalloy10.1088/1757-899X/82/1/012033 ↗
87. Geometrically necessary dislocation and size-dependent plasticity10.1016/S1359-6462(02)00329-9 ↗
88. Preface to the viewpoint set on: geometrically necessary dislocations and size dependent plasticity10.1016/S1359-6462(02)00336-6 ↗
89. Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues10.1016/S1359-6462(02)00335-4 ↗
90. An objective study of substructural boundary alignment in aluminium10.1016/S1359-6454(03)00277-5 ↗
91. Strain mapping near a triple junction in strained Ni-based alloy using EBSD and biaxial nanogauges10.1016/j.actamat.2011.01.051 ↗
92. A new approach for determining GND and SSD densities based on indentation size effect: an application to additive-manufactured Hastelloy X10.1016/j.jmst.2021.05.005 ↗
93. Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density10.1016/S1359-6454(99)00020-8 ↗
94. Scaling of the spacing of deformation induced dislocation boundaries10.1016/S1359-6454(99)00474-7 ↗
95. High-temperature stress and strain partitioning in duplex stainless steel